- Put the ignition on with your key. Turn the key to the first position.
- On the dashboard, press the reset trip meter button. Hold it down for a few seconds.
- Hold the odometer button down for around five seconds.
- Release the odometer button after it is off.
In This Article...
How can you turn a 2013 Toyota Rav4’s maintenance light back on?
In order to start the car, turn the ignition to position one with your key in the ignition. Turn the key to position two while pressing and holding the trip meter reset button on the dashboard. For 10 seconds, keep your finger on the odometer button. Then the light should flash, beep, and finally turn off.
Why does my Rav4 indicate that maintenance is needed?
The significance of the emblem MAINT REQD is significant. The MAINT REQD light indicates when the vehicle’s scheduled maintenance is due when it illuminates. If your car is under two years old, this service can be covered by your ToyotaCare plan.
Why does the maintenance light not go out?
The Maintenance Required Light that flashes on the instrument panel is reset using the processes that Lexus walks us through.
Keep in mind that after doing maintenance, the light should be reset using the following procedure:
- the ON position on the ignition switch
- Set the trip display to TRIP A mode on the odometer.
- Switch the ignition to the “OFF” position.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- The service reminder light for maintenance will
The Trip Meter RESET button should be released.
7. Insert the key in the OFF position.
8. Ensure the Service Maintenance Reminder Light turns off by turning the ignition to the ON position. NOTE: If the light in step 5a keeps flashing, turn off the ignition and follow the steps from step 1 again.
How can you turn a Toyota’s maintenance light back on?
A Toyota Maintenance Light Reset
- In order to start the car, turn the ignition to position one after inserting your key.
- Turn your key to position two after pressing and holding the trip meter reset button on the dashboard.
- Hold the odometer button down for a further ten seconds.
Why does my maintenance light come on after I change the oil?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
What happens after I change the oil in my car?
Reset Oil Change Indicator
- Turn on the ignition.
- Both the stop and accelerator pedals should be fully depressed.
- Maintain firm pressure on the brake and accelerator pedals.
- A notice verifying the reset process is ongoing appears after three seconds.
Why does my Toyota state it needs maintenance?
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Press and hold the ODO reset / readout button while the engine is off.
- Now the light will read “MAINT REQD.”
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- If the car is on, turn it off.
- The ODO display will briefly flash before beginning to display only zeros.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
Can I drive my automobile even though it needs maintenance?
Simply put, the flashing maintenance required light is alerting you that maintenance on your car is necessary. The indicator will come on when a predetermined period of time has passed since your car’s last service or based on how far you’ve driven it.
This light typically indicates that you should change the oil in your car. The maintenance data will be reset for you when your car has been taken in for service.
To manually reset the system to turn off the light, however, follow these instructions:
When the maintenance light comes on, you can continue to drive, but bear in mind that you are doing so at your own risk if the required or scheduled repair is skipped.
Why does my car mention that it needs maintenance?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.
What distinguishes a maintenance requirement from a check engine light?
Many people are unsure of what each of these lights means, and the check engine light and the service engine soon light are frequently confused for one another. We’ll describe how distinct they actually are despite the fact that they appear to be similar.
Authored by: Bradley Hayes, Director of Marketing at Autoscope European Car Repair and Automotive Blogger
Since Karl Benz originally unveiled his Benz Patent Motorwagen, automotive technology has advanced significantly. In fact, the notion that computers are essentially controlling our cars in today’s computer-driven society shouldn’t be shocking. In order to assure the precise right operation of your vehicle’s numerous systems and components, they regulate and track their performance. They even notify the driver when the automobile needs repair or maintenance. While technology hasn’t yet given our cars voices (like Kitt from Knight Rider), it has made it possible for them to communicate in other ways, such as through a series of backlit symbols that show up in your instrument cluster, such as a “check engine” and a “service engine” light.