There is a technique to reset the liftgate on your Toyota Highlander if it is giving you problems. Therefore, try this reset method first before taking it to the Toyota shop for repair. It simply takes a few minutes and is simple to complete.
To reset the liftgate on your Toyota Highlander, do the following:
- Put your car in park and turn it off.
- Head to the Highlander’s back.
- Liftgate button should be pressed.
- Open the liftgate.
- The liftgate button should be pressed and held.
- After pausing for a moment, it will beep twice more.
- Reopen the liftgate after it has been closed.
- The liftgate of the Highland has been reset.
By adjusting your Toyota Highlander’s liftgate back to the default position, you might have avoided a trip to the dealer and a significant repair expense. We will explain the need to reset the liftgate in this article and provide step-by-step instructions.
Continue reading for answers to more frequently asked questions about the Highlander.
In This Article...
What should I do if the trunk of my Toyota Highlander won’t close?
You always count on the power rear door to open easily for you. It can fail occasionally, which is disappointing.
The rear liftgate closure button can be pressed and held down to solve this issue quickly. It will beep repeatedly before releasing. In most circumstances, doing so will reset the liftgate and enable it to function properly.
In circumstances like this, it can be difficult to know what to do. We’ll explain that information in more detail now and let you know what to anticipate if your liftgate isn’t functioning properly. For further information and assistance, you may also look up the vehicle history.
Why won’t my power liftgate operate?
At Texas Hydraulic, we provide a fully stocked and equipped repair facility manned by a highly qualified group of technicians. But before you visit our Dallas-Fort Worth full-service repair facility, you might opt to try to solve the problem on your own.
We completely get, which is why we have written the guide below for troubleshooting the hydraulic liftgate on your truck. Here are a few of the most frequent causes of a malfunctioning box truck liftgate.
The next most likely culprit, if your motor is operating and everything else appears to be in working order, is low battery voltage. To determine whether the battery is the problem, try using a booster. As advised by the manufacturers, always make sure the truck is running before using the liftgate. If the booster doesn’t fix the problem, you could need to replace the battery; in that case, it’s advisable to seek out experts for OEM parts and skilled installation.
Make sure the hydraulic reservoir oil level is within the permitted range for your particular model by checking the level. If the level is too low, it will be difficult for the gate to raise itself to deck height. The suggested fluid level can be found in the owner’s manual for your liftgate. The liquid will purge from the reservoir’s breather cap if the tank is overfilled. Run the gate several times to drain all extra fluid.
If the problem is a squeaking sound, it is probably due to a lack of lubrication or issues with the power unit’s internal gears, pulleys, or sprockets. For chains or pivot points, try using a lubricant made for lift gates. If that doesn’t address the problem, you might need to rebuild or replace the pump.
How Do You Reset the Liftgate on a Toyota Highlander?
You can use the door control or the key fob to reset your liftgate. Ensure that all doors are closed before pressing and holding the power liftgate button for three seconds to control the doors.
Push and hold the lock and unlock buttons on the key fob simultaneously for three seconds. Your Toyota Highlander’s liftgate should now be reset.
How Do You Manually Open the Highlander trunk?
There are two ways to manually open the Highlander trunk. The first method involves using the release handle, which is situated inside the car on the cargo area’s left side.
The power liftgate button can also be pressed and held for three seconds. The liftgate will start to open a little as a result, allowing you to manually lower it.
How Do I Turn on My Power Liftgate?
Your power liftgate is simple to turn on. Make sure all doors are shut first. The power liftgate button should then be pressed and held for three seconds. This will activate the power liftgate on your Highlander.
On a rav4, how do you reset the lift gate?
Open the liftgate, then manually adjust the height to your liking. Once everything is in place, press and hold the INSIDE button for 3 seconds or until the system beeps twice, and then let go. To confirm the height modification, restart the Power Liftgate System.
How do I silence the beeping on my Toyota Highlander?
The Toyota Highlander’s dash camera, faulty seatbelt sensors, poor electrical connections, low keyfob battery, low tire pressure, broken door latches, or one of the driver aid systems are the most typical blaring causes.
Spare Keys Left in Vehicle
When you go to lock your Highlander, if you have a spare set of keys inside, you can hear a warning sound because the car assumes you are trying to lock the keys inside the truck.
Dash Camera
You’ll probably hear this beep at startup if your dashcam was installed by Toyota at the factory.
If you look behind your rearview mirror, where the dashcam is positioned, you will see the dashcam blinking, but you won’t see any warning lights appear on the dashboard.
You could realize the micro SD card has not been fully inserted into the camera if you see an error flash.
If the SD card is in, though, and it’s still beeping, hold down the “action” button as you start the car.
- Ensure that the car is totally turned off.
- Make sure your parking spot is level.
- Verify that the camera is turned off.
- Keep holding down the action button.
- then drive off in your car
Loose Connection:Seat Belt Sensors
It is important to inspect the plastic wire connectors under each seat in the car to make sure they are all tightly fastened.
Seatbelt Alarm& Weight on Seat
Your seatbelt’s fastening may not be detected by a sensor because it is malfunctioning.
As an alternative, you might have a bag of groceries or other weight on the passenger seat that is setting off an alarm.
What went wrong with my automatic trunk?
When you press the inside trunk release button on the fob or the trunk lock actuator and nothing happens, this is another common clue that there is a problem. This could be a sign of a problem with the vehicle’s battery or with the electronics connecting to the actuator, such as a shorted fuse or wire. Since there are numerous potential issues that could result in this problem, it is recommended to get in touch with a nearby mechanic so they can accurately diagnose and resolve the problem as soon as possible.
How can I activate the power on my liftgate?
- As soon as you are 6 feet away from the rear of your car, the logo projection will automatically turn on.
- Kick directly over the logo or, for earlier vehicles, at the sensor. Note: The sensor will not be activated by kicking straight within 5 inches of the bumper, sweeping the foot from side to side, or stepping on the projected logo.
- You will have time to safely exit before the liftgate opens. When the liftgate opens, the rear lights will flash and a chime will ring to let you know.
The liftgate can also be closed by kicking it:
- Kick directly at the sensor for earlier vehicles or over the projected logo.
- The liftgate will close after a 2-second delay, at which point the back lights will flash and a sound will chime.
Describe the power back door.
Whether locked* or unlocked, the power back door can be opened. The power rear door can be stopped from opening or shutting by pressing the switch. To operate the power rear door in the opposite direction, press and hold the switch once again for around one second.
Electrical system
Some aftermarket replacement windshields for Toyota Highlander models from 2014 to 2018 are being recalled by Fujian Wanda Automobile Glass Industry (Wanda). Water may flow into the wire harness that is attached to the windshields, thus damaging the engine control module of the car (ECM).
Because of the ECM damage, there is a higher chance of an accident if the engine stalls.
Wanda will inform owners, and service facilities will free of charge fix the windshields, check the ECM for damage, and replace it if needed. 2019-01-29 marked the start of the recall. Wanda customer care can be reached at 1-864-281-2760 by owners.
Service brakes, hydraulic: Fluid
Toyota Motor Engineering & Manufacturing (Toyota) is recalling a few Highlander models from the 2016 model year that were produced between May 26 and September 16, 2016. The wire harness of the brake fluid level sensor might not be attached, which would prevent the sensor from detecting the amount of braking fluid. Because of this, the Federal Motor Vehicle Safety Standard (FMVSS) No. 135, “Light Vehicle Brake Systems,” is not met by these automobiles.
Low brake fluid levels may affect braking performance and raise the possibility of a collision if they go undetected.
Owners will be informed by Toyota, and dealers will check the wire harness and connect it to the sensor for no charge if needed. Beginning on November 14, 2016, the recall. The toyota customer support number is 1-800-331-4331. For this G03, Toyota’s number.
Equipment: Other: Labels
Several vehicles from the model years 2016 Toyota Camry and Highlander, 2015-2016 Toyota Tundra, Scion FR-S, and tC are being recalled by Southeast Toyota Distributors, LLC (SET). The extra weight of the installed accessories may not be accurately reflected on the Load Carrying Capacity Modification Label. The Federal Motor Vehicle Safety Standard number 110, “Tire Selection and Rims for Passenger Cars,” is not met by these automobiles.
An inaccurate label could prompt the owner to overload the car, which would raise the crash risk.
SET will give owners notice and a free replacement label to be applied over the incorrect label. A recall was initiated on July 14, 2016. Owners can call 1-866-405-4226 to speak with SET customer care.