You must start the engine and hold down the disp or trip button until the panel reads trip A in order to reset the oil life indicator on your 2017 Toyota RAV4. When you get there, you can turn the ignition to the lock position, but you shouldn’t start the engine. Now turn the key to the OFF position while maintaining pressure on the trip button. Finally, you must release the button while turning the key back to the lock position. Your indicator should now indicate “0 miles,” and you can resume using your car normally.
You may turn off the oil light on your Toyota Highlander by following these instructions: Don’t start the engine after turning the ignition switch to the “on” position. If your vehicle has a start push button, press it without depressing the brake pedal. To see “trip a,” briefly click the odometer knob. To start, turn the ignition switch to the “on” position, then click and hold the “reset trip odometer” button. Hold down the reset trip odometer button until “000000” miles appear on the indicator and the maintenance light goes out.
In This Article...
How can I turn my Toyota RAV4’s maintenance light back on?
How to Extinguish the Toyota RAV4’s Maintenance Light
- Put the ignition on with your key. Turn the key to the first position.
- On the dashboard, press the reset trip meter button. Hold it down for a couple of seconds.
- Hold the odometer button down for another five or so seconds.
- Release the odometer button after it is off.
Why does my Rav4 indicate that maintenance is needed?
The significance of the emblem MAINT REQD is significant. The MAINT REQD light indicates when the vehicle’s scheduled maintenance is due when it illuminates. If your car is under two years old, this service can be covered by your ToyotaCare plan.
How should I respond if my maintenance light illuminates?
How Can the Maintenance Required Light Be Reset?
- Turn on your car. Look at your dashboard when your key is in the on position.
- Press the Trip Meter Reset Button after turning off the engine.
- Re-start the vehicle.
- Keep pressing the reset button.
- Reset button released
Why does my Toyota state it needs maintenance?
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Now the light will read “MAINT REQD.”
- The ODO display will briefly flash before beginning to display only zeros.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Press and hold the ODO reset / readout button while the engine is off.
- If the car is on, turn it off.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
How can my Toyota maintenance be reset?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
How can I turn off the maintenance is necessary light?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
Why, after an oil change, is my maintenance required light still on?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.