The Toyota RAV4 has a maintenance reminder that can be reset in two different ways. Please adhere to the instructions listed below for your particular car’s trim level.
In this first lesson, I’ll demonstrate how to turn off the maintenance light on a RAV4 with a monochrome screen. So, the following is how to reset it:
- Next, switch the light off.
- By continually pressing the DISP button, navigate to TRIP A.
- Hold down the DISP button while waiting for the maintenance light to turn off.
- While restarting the ignition, press and hold the DISP button.
- Activate the ignition switch without starting the engine.
In This Article...
On a Toyota Rav4, how can you reset the maintenance?
How to Extinguish the Toyota RAV4’s Maintenance Light
- Put the ignition on with your key. Turn the key to the first position.
- On the dashboard, press the reset trip meter button. Hold it down for a couple of seconds.
- Hold the odometer button down for another five or so seconds.
- Release the odometer button after it is off.
How can I dim the maintenance is necessary light?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
How can I turn off the Toyota maintenance is required light?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
Why does my Rav4 indicate that maintenance is soon needed?
The significance of the emblem MAINT REQD is significant. The MAINT REQD light indicates when the vehicle’s scheduled maintenance is due when it illuminates. If your car is under two years old, this service can be covered by your ToyotaCare plan.
Why does my maintenance light come on after I change the oil?
- Now the light will read “MAINT REQD.”
- Press and hold the ODO reset / readout button while the engine is off.
- The ODO display will briefly flash before beginning to display only zeros.
- If the car is on, turn it off.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
On a 2013 Toyota Tundra, how do you turn the maintenance light back on?
- Without starting the engine, turn the ignition to the “On position. If your car has a push-button ignition, press “Start” without depressing the brake pedal.
- By pushing the display change button or “Trip button,” you can change the display to “Trip A.”
- Completely shut off the car.
- Keep holding down the “Trip button.”
- Hold the “Trip button down while turning the ignition to “On without starting the car.
- Release the “Trip button” whenever the trip meter reads “all zeros.”
How should I respond if my maintenance light illuminates?
How Can the Maintenance Required Light Be Reset?
- Turn on your car. Look at your dashboard when your key is in the on position.
- Press the Trip Meter Reset Button after turning off the engine.
- Re-start the vehicle.
- Keep pressing the reset button.
- Reset button released
Why does my Toyota indicate that maintenance is soon needed?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.