Push and hold the odometer button on your dashboard briefly, then quickly turn your key to the second position. Hold the odometer button down for a further 10 seconds. The maintenance light should flash and you could hear a beeping if everything is done correctly. Your Toyota Camry’s maintenance light ought to go out after doing that.
In This Article...
How do I stop the needed maintenance?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
On a 2008 Toyota Camry, how do you turn off the maintenance is necessary light?
It only takes a few minutes to get the hang of turning off the maintenance light on a Toyota Camry, but you’ll need to act quickly! To be ready for each stepthe timing might be trickywe advise reading the instructions several times before you begin.
- Switch to position one after inserting your key into the ignition. The first set before starting the engine is this.
- Turn the key to position two while pressing and holding the odometer button on the dashboard.
- When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
- Pull back on the odometer button, then turn the key.
- When you turn on your automobile, if the light is off, the procedure is finished.
- If the light is still on, try it again.
How can you turn a Toyota’s maintenance needed light back on?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
Why does my car indicate maintenance is needed following an oil change?
- Press and hold the ODO reset / readout button while the engine is off.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- If the car is on, turn it off.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Now the light will read “MAINT REQD.”
- The ODO display will briefly flash before beginning to display only zeros.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
What happens after I change the oil in my car?
Reset Oil Change Indicator
- Turn on the ignition.
- Both the stop and accelerator pedals should be fully depressed.
- Maintain firm pressure on the brake and accelerator pedals.
- A notice verifying the reset process is ongoing appears after three seconds.
Why, after an oil change, is my maintenance required light still on?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.