Before attempting to reset the airbag light on your car, you should have it checked by a mechanic to make sure there is nothing wrong with it. Additionally, you might wish to look into any active vehicle recalls. Your car’s airbags are a crucial safety feature that must always function properly.
Having said that, you may remove a fuse from your car’s dashboard and reset the airbag light on a 2006 Toyota Sienna. If doing so makes you uncomfortable, you might wish to hire a mechanic.
If so, take these instructions to turn the Sienna’s airbag light back on:
- By turning the key once in the ignition, you can put the automobile in auxiliary mode. Never start the car.
- Give the car at least five minutes to idle.
- To pry open the portion of your dashboard to the left of your steering wheel, use a flathead screwdriver. The fuses can be found here.
- You can find a diagram of the fuses on the back of the panel you just removed. Look in your owners handbook if you do not see a diagram.
- Once you’ve located the correct fuse, remove it, wait, then replace it. Your airbag light will reset as a result.
After turning off the airbag light, you’ll be able to travel with a little more confidence. Check out the Jerry app to see how much you may save on your auto insurance premium before you get back on the road.
After you download Jerry, simply respond to a few questions that should take you no longer than 45 seconds to finish, and you’ll receive car insurance rates for coverage that is comparable to your current plan right away. Customers of Jerry save $887 year on average.
In This Article...
How can you turn a Toyota’s airbag light back on?
When you experience the same problem, you should start by following this technique, which is identical to resetting the airbag light on a Toyota Camry. It needs timing the airbag light and has four straightforward stages that are simple to complete.
First, activate the ignition. Wait for the airbag light to turn on next; it typically illuminates for seven seconds before turning off automatically. After waiting three seconds, immediately flip the ignition switch off. Before starting the engine, go through the basic procedures a couple of times. Your car’s airbag light should illuminate for seven seconds before turning off permanently if everything is done correctly.
Can the airbag light be reset without a tool?
Without a scanner, most automobile models make it difficult to reset the airbag light. This is a safety warning since, when the airbag light appeared, you should always fix the problem. Fortunately, if you fix the issue, the airbag light will typically also turn off by itself in many automobile models.
However, in some older vehicles, the airbag light can be reset without a scanner by disconnecting the battery wires.
Make that there are no loose wires or rust in the connector plugs in the wiring system under the driver’s or passenger’s seat. Restart your car after spraying an electronic cleaner on the connecting plugs.
If you can’t detect any issues there, you should really invest in an OBD2 scanner or have a shop interpret the codes because otherwise you’ll have to guess what the issue is.
Headlight indicator (U.S.A.)
informs you that the headlights, taillights, instrument panel lights, parking lights, license plate lights, and side marker lights are all on.
Low fuel level warning light
notifies you when the fuel is running low. For more detailed information on how much petrol is left in your Toyota, consult the owner’s manual.
Maintenance required reminder
At our Toyota dealership in Morrow, many of the new Toyota models we have available for sale are equipped with a maintenance-required reminder light to make sure you perform the needed maintenance.
Security indicator
When the ENGINE START STOP switch is turned off in a car equipped with a smart key system, the light flashes to indicate that the system is working. The light will flash on Toyota vehicles without a Smart Key System once the key is taken out of the ignition.
Slip indicator
The slip indicator will light up when your car starts to lose traction and slide. You will be informed that the VSC/TRAC systems are operational via this.
SRS airbag on-off indicator
You can tell if the passenger air bag is on or off by looking at the AIRBAG ON and AIRBAG OFF light, which lights. To properly activate or deactivate the airbag, this device senses the conditions of the front passenger seat.
TRAC OFF Indicator & VSC Off Indicator
informs you whether TRAC and/or VSC have been turned off. TRAC and BSC can reduce engine output to the wheels if your Toyota becomes stuck in fresh snow or mud. When the system is turned off, you might be able to liberate the car by rocking it back and forth. For information on how to disable this function in your individual model, contact our Toyota service team.
What does it cost to repair the airbag light?
Reset Airbag Light, at No. 1 This procedure typically takes several hours and costs a few hundred dollars, though depending on the car, it might cost as much as $600.
Airbag Deactivated
The airbag system is usually turned off or deactivated when the airbag light first illuminates. There can be a few factors behind this over which you have no control.
A crash sensor, SRS module, or other airbag component can be malfunctioning. Alternately, it’s possible that the sensor in the passenger seatwhich decides whether or not that airbag should be activeis broken.
Seat Belt Issue
As was already said, the airbag light could turn on if you don’t fasten your seatbelt. But this light might also turn on as a result of other seat belt problems.
Maybe your seat belt won’t remain in place in the buckle and snap shut. Perhaps there is a problem with the sensors in the buckle, and they are unable to properly inform the computer that you have buckled up.
Alternately, a seat belt pre-tensioner issue may exist and necessitate repair or replacement.
Small Accident
Even if your airbags don’t deploy in a minor collision (sometimes known as a “fender bender”), the crash sensors may still go off. This means that unless you visit a car repair shop or an airbag specialist to have it fixed and the necessary parts replaced, your airbag light will remain on.
A minor collision could occur if you are traveling under 8 mph and hit something with the front of your car. The crash sensors often respond quickly to any kind of accident, no matter how serious or little.
Water Damage
The crash sensors of your airbag system may develop rust if the interior parts of your car have water damage for any reason.
Their capacity to work properly will be distorted by this corrosion, which could cause the airbag light to illuminate.
Airbag System Not Reset
Simply replacing the airbag is insufficient after an accident that causes the airbags to deploy. Additionally, replacement is required for the SRS’s crash sensors, clock spring, seat belt pretensioners, and other parts. The brains of the airbag system, the airbag monitoring unit, will also need to be reset or reprogrammed.
To allow the airbag system to function once again, you must have the SRS module reset or reprogrammed by a competent mechanic or dealership. Another option is to ship the airbag monitoring unit to some businesses, which will reset it for a price and send it back to you prepared for installation.
How can the airbag light be turned off?
You can avoid a trip to the dealer or mechanic by resetting the airbag light on your car in the garage at your house. The SRS light (supplemental restraint system), commonly known as the airbag light, illuminates on the instrument panel of the car typically only after an accident and after the airbag has been deployed. However, there are other situations that could set off the SRS light, like when a new radio is installed or when there is a problem with the airbag system itself. You can reset the airbag light yourself using a handheld computer tool that you can get from an auto parts store once all repairs have been made.
Step 2
Pay attention for the airbag light to activate. It will remain lit for seven seconds before turning off on its own. Turn the switch off right away and wait three seconds after it shuts off.
Step 3
Start the car. The SRS light should illuminate for seven seconds before going out completely. Resetting the airbag light was done.
- David; 2003. “OBD II Fault Codes Reference Guide”
- Martin; 2008, “How To Use Automotive Diagnostic Scanners (Motorbooks Workshop)”
- clock or watch with a second hand
- You run the danger of the airbag inflating unintentionally if you keep driving while the SRS light is on.