You’re probably right because key fob batteries need to be changed occasionally. To replace the battery in a Toyota RAV4 key, simply carry out the following steps:
- Carefully pry apart the two halves of the plastic key part using a flathead screwdriver.
- Take the module out of the key.
- With the flathead screwdriver or the edge of a coin, carefully pry the module open.
- Note the locations of the positive and negative ends when you remove the old battery from its housing.
- Put a fresh CR2016 battery in place of the old one.
- Replace the module inside the key after snapping it shut.
- Close the key with a snap and check the remote’s functionality.
Why not spend a little more time with Jerry discussing your insurance options while you’re learning more about your car key?
Jerry is a free insurance comparison software that checks around for the best deals with more than 50 different insurance providers. You may make adjustments at any time, receive prices instantly, and text an agent with any queries you may have.
In This Article...
What kind of battery does a key fob for a 2016 Toyota Rav4 require?
A Toyota key fob battery replacement may be necessary if your Toyota key fob suddenly stops functioning. The first step in the relatively straightforward procedure is to open the case and look for the battery. Find out below how to access a Toyota Key fob:
- A concealed key that you must remove and place in the slot intended to open the case can be found in new Toyota models.
- For older models, you’ll need to pry open the obvious notch on the case with a thin item.
Once the Toyota key fob has been opened, you should continue with the other stages in this guide to replacing the key fob’s battery:
- To make the battery visible, gently raise the circuit board.
- Note the type of battery being used and how it is positioned inside the case. A CR2032 battery, which you can get in shops and online, is used by the majority of Toyota models. These batteries are really inexpensive, usually costing less than $5.
- Replace the battery in your Toyota key fob within the casing, then cap it off.
- Check the Toyota key fob battery replacement now to make sure it’s operating. If it doesn’t work, check the connections to make sure they are clean and in contact with the battery before opening the case once more. If it still isn’t working, you might want a replacement Toyota key fob.
How long does the battery in a Toyota key fob last?
When your Toyota key fob’s battery is running lowthe typical battery life is one to two yearsan alert will sound when the engine is turned off.
The battery in my Toyota key fob has to be changed.
How to Replace the Battery in a Toyota Key Fob.
- Take the key out of the fob. Over the key portion of your key fob is a tiny metal button.
- Unlock the fob.
- Dispense with the green circuit board.
- Switch out the battery.
- Place the key inside the fob after putting the fob back together.
Which battery should I use in my 2018 Rav4 key fob?
Pull the tab containing your emergency (manual) key and depress the button on the side of your Smart Key. If your Smart Key’s battery dies, you can still unlock the vehicle using this method. The Smart Key case may be broken in half with the emergency key once the manual key has been removed, revealing the battery. The battery will pop out if you pull down on the tab keeping it in. Snap the Smart Key back together after replacing it with a fresh CR1632 battery (some models use a CR2032 battery).
A 2017 Rav4 key fob requires what kind of battery?
A CR2032 battery is typically available at big box stores and hardware stores in Watsonville. Most places have prices that are under $5. Replace the Toyota key fob batteries, then put it in the case and snap the key fob shut. Test your key fob after changing the battery.
How is a 2016 Toyota Rav4 key fob programmed?
How to Set Up a Toyota Car Remote
- Within five seconds, turn your ignition key from “off” to “on” again.
- Close and reopen the driver door twice in the following 40 seconds. Then, put the key in and take it out of the ignition once again.
- Once more, make sure you finish steps 1 and 2 within 40 seconds.
If the battery in my key dies, would my car stop?
This issue has been foreseen by automakers ever since the key fob was created. Nothing will happen if your key fob dies while you’re driving. Simply because the key fob is a locking and starting device only, the automobile will continue to run. The key fob has no influence over the ignition or engine once the automobile is moving.
Even though you’ll need to go to a general store or pharmacy to get the battery, replacing the battery in your key fob simply takes a few minutes if you’re pressed for time.
Why not take the time to renew your auto insurance at the same time as you’re replacing the batteries in your key fob?
You can access a new quotation with just a few taps on your phone screen by downloading the Jerry app and answering a few questions.
Jerry assists you in finding and comparing rates from more than 50 leading suppliers in minutes as a licensed broker. Jerry can assist you with purchasing new insurance and even canceling your existing policy when you find a lower rate.
Can a dead key fob battery still start a car?
- On your key fob’s back, search for a tiny sliding button. You can slide the key fob cover off or click a button to do so. To get it to release, you might need to use your fingernail and a little force.
- Use the mechanical key to unlock the door after you get it. If your door doesn’t have a key slot, it’s likely concealed behind the handle cover. To access the key slot, carefully remove the handle cover by using the key.
Now that you’re inside, here’s how to start the car with a dead key fob:
- Close the key fob after inserting the mechanical key once more.
- Press the START button with the key fob. Instead than pressing the button with your finger as usual, push the key fob against it. Many manufacturers utilize this backup device to make sure the car can start even if the key fob is dead.
- Some vehicles have a secret key fob slot that can be used to start the engine. For instance, the backup slot is located inside the cup holder in some Ford models. Your fob will fit perfectly in the slot. Use the push button start as usual after inserting the dead key fob into the holder.
- Check the steering column for a physical key slot if neither of these approaches succeeds (some Mazda models have this feature). To start the car, place the mechanical key within the keyhole.
If I change the battery, do I need to reprogram my key fob?
A remote key fob needs to be associated with your vehicle particularly in order to be secure.
This stops people who drive the same make and model of automobile as you from using their remote to access your car. You’ll need to reprogram the fob if changing the batteries has erased this connection or if it was somehow disrupted in order for it to once again recognize your automobile.
Standard programming sequence
Your key fob can typically be reconfigured by following this typical procedure:
Instead of starting and then returning to the locked position, turn the key into the run position. Repeat this multiple times.
You’ll typically hear a chime or other sound when you’ve cycled the key enough times. At that point, you can push the lock or unlock button on your key fob to hear another chime.