How To Remove Toyota Tacoma Headlight Assembly

Toyota / By

The lights and grill surrounding the headlights must be removed in order to replace the headlamp assembly in your Toyota Tacoma pickup, but this can be done with a few hand tools. To light up the road and the area in front of the vehicle, the headlight assemblies are made of a composite material. Moisture or debris entering the assembly can reduce bulb life if the assembly is damaged. If the headlight assemblies are stained or severely scratched, they could also need to be replaced.

Step 1

Your Tacoma’s hood may be opened, and the prop rod can be used to support it. Find the three screws holding the side marker lights in place. One screw is on the top of the light, and there are two screws in the lens. Utilizing a screwdriver, take out all three.

Step 2

Unplug the electrical connector on the back of the marker light assembly before removing it from the truck. Set away the electrical connector. On the marker light opposite, repeat this procedure.

Step 3

Find the seven clips that hold the grill in place on the truck’s front. There are three on the bottom and four along the top of the grill. Pushing the clip downward with a flat screwdriver can release it.

Step 4

Find the two clips on the grill’s lower corners. In the grill’s lowest corner, there is one on either end. To loosen these clips, reach through the opening in the marker light with a pair of long-nosed pliers.

Step 5

Remove the nine clips and the grill, then set the entire assembly aside. On the headlamp assembly, find the two nuts and one bolt. Slide the headlight assembly forward after removing them with a socket and ratchet. Remove the headlight assembly from the truck and unplug the electrical connector from the headlamp.

Step 6

Install the retention bolt and two retaining nuts after sliding the new headlight assembly into the truck and plugging in the electrical hookup. With a socket and ratchet, tighten the bolt and nuts.

Step 7

Reengage the nine clips holding the grill in place as you position it on the truck. To fasten the grill, snap the clips back onto the truck’s body. You’ll see that they secure themselves.

Step 8

Plugging the electrical connector into the back of it will allow you to install the side marker lights. With a Phillips screwdriver, attach the three retention bolts and tighten them. The lens will break if the screws are overtightened.

  • tool for Phillips screws
  • flat-head screwdriver
  • extended-nose pliers
  • Set of metric sockets

How is a complete headlamp assembly removed?

Instructions

  • First, take out the outdated headlamp assembly.
  • Disconnect the assembly in step two.
  • To remove the headlamp retaining ring from the headlamp, turn it counterclockwise.
  • Step 3: Cut off the electricity.
  • 4. Remove the previous assembly.
  • Replace the assembly in step five.
  • Connect the new assembly in step six.

How much time is required to replace a headlight assembly?

  • Pick a spot with sufficient lighting in your garage or a tidy portion of your driveway to work on your car. Be calm and give yourself plenty of time (at least two hours) to change a headlight. It can be straightforward, but it also might turn out to be trickier than you anticipated.
  • Any fasteners and retaining clips you’ve taken off should go in a container or jar. Otherwise, they’d be too simple to lose.
  • Mark the location of the wiring removal with masking tape and a felt-tip pen to ensure that it is reinstalled accurately.
  • Kneeling or working beneath the car can be made more comfortable by using an old throw rug, a rubber mat, or a sizable piece of clean cardboard to lie on.
  • When connections are made, keep an eye out for a loud click.

We anticipate that your headlight replacement efforts will succeed if you follow these advice. We also hope that you don’t need to replace as many bulbs as this guy:

Can you change a headlight’s plastic cover?

Many people choose to replace their own headlamp covers in order to save money. If money is not a concern for you, hiring an expert is usually simpler.

DIY

Pros:

  • Cheaper Labor prices won’t be an issue for you.
  • Quicker
  • There are no waiting periods like at auto repair businesses.

Cons:

  • You might not correctly attach the cover.
  • You may make mistakes and harm others.

Auto shop

  • It is correctly replaced the first time.
  • They are equipped with everything required to meet your vehicle’s specific headlight cover requirements.
  • greater expense
  • You’ll be without a vehicle for one or two days.