There is a terrible noise coming from the front right of my 1999 Toyota Corolla. Only when the car is starting to drive and the engine is vibrating slightly does it make noise. I’ve been wondering that the engine vibration may be caused by the engine mounts or the exhaust pipes shifting.
But tonight I discover that the screw holding the right fender to the “A” pillar is gone. When you open the right door, you can see it. The fender is fastened to the chassis using a “L”-shaped bracket. If I put pressure on various parts of the fender, this will move and make a noise that is quite similar to the rattle I hear (this is close to where the rear view mirror, windshield pillar, and the fender meet). I can understand how the engine’s vibrations may cause the fender to tremble and produce that sound.
The only issue is that I’m not sure exactly how to remove the fender. I have to remove the fender in order to replace the L-shaped bracket, which is also missing and cannot be replaced without doing so.
What parts (bumper, turn signals, etc.) do I need to remove in order to remove the screws holding the feder to the chassis?
It wouldn’t harm to fix it even though I’m not sure whether this is what is making the noise.
You are a great help. I have a Haynes handbook, however it is missing instructions on how to remove the fender.
In This Article...
How is a Toyota fender removed?
Instructions
- the front bumper cover must be removed (see separate video)
- While the front door is open, remove the 10 mm fasteners.
- Using a flat-tip screwdriver, remove the top plastic fastener.
- Using a plastic trim stick, release the front headlight assembly, then unplug the electrical connector.
- Along the top of the fender assembly, remove three 10mm fasteners.
Is changing a fender difficult?
Pickup vehicle owners have a large social network. On a regular basis, people use my pickup to transport anything from cordwood and college students to upright pianos and snowblowers. I used to constantly ride shotgun to protect my truck while it was new, but it got stale once I realized I would always be the mover’s assistant.
Then, a friend struck a low post with the right front corner of his car by accident, causing just enough damage to the fender to exceed his financial means but not enough to surpass my deductible.
Since only the fender was damaged, I reasoned that I could easily purchase a replacement and bolt it on myself. If you’re prepared to color-sand and buff out the finish once it’s dried, modern basecoat/clearcoat paints make a professional refinishing job relatively simple with nothing more than an air compressor and spray gun.
When looking for a replacement fender, there used to be two options: purchase one from a dealer or locate a reliable used one at a wrecking yard. There are a lot more possibilities available now.
You can purchase an aftermarket fender that is less expensive than the factory fender, just as you can purchase many types of aftermarket shock absorbers or batteries for your vehicle. This is especially true for cars with the same body style over a long period of time.
It’s a good idea to paint the new fender’s hidden surfaces with something more rust-resistant than the primer used at the stamping factory after you get it home. As long as you clean and carefully sand the primer first, rattle-can enamel is acceptable. Degreasing the surface with a prep solvent is the last step before spraying any paint.
There are several different ways to remove a fender. Depending on the vehicle, this task may be simple or challenging. Consider where fasteners are and what you might need to remove first when removing any fender, such as the bumper, antenna, grille, or headlight bucket. On some cars, the interior of the fender is where the hood hinge is bolted. If so, you must prop the hood open in order to take out the fastener there. The hood may be less vulnerable to harm during the repair process if it is completely removed. If necessary, use a scribe or felt pen to record the location of the hinges’ attachment to the hood so that it will be simple to realign them later.
Remove any cladding, marker lights, or trim elements from the fender as well. Most likely, you’ll want to reuse them, so be cautious. Trimpieces in general can be challenging to remove because extremely strong double-sided tape is used to secure them. You can remove the trim without bending it by using Goof-Off, 3M Trim Adhesive Remover, or even lacquer thinner to weaken the adhesive.
Remove the rusted, old fender’s bolts. Avoid working up a sweat yanking until you are certain that all of the fasteners have been taken out because they may be in unexpected locations.
Painting isn’t as intimidating as it once was. Modern basecoat/clearcoat paints can be sprayed with ease utilizing basic tools from a home workshop.
You might also need to use a utility knife to cut through any undercoating or seam sealant that keeps the fender attached to the body. Be careful not to dent the door or hood when lifting off the fender.
Install the fender by setting it on the car and securing it with a number of loosely fastened fasteners. Most fender fasteners and their mounting locations have some flexibility while they’re loose, allowing the fender to be fitted. To produce a uniform gap at the door and hood seams while ensuring that the fender is flush with the body, tighten all fasteners to the point of fingertip tightness. Check the fit and make sure the door and hood open and close properly after tightening all bolts. Remove any components from the fender that will prevent it from being painted.
OEM and aftermarket fenders both come pre-coated with a tough primer sealer that is prepared to take paint. Mask off the hood, the door next to the fender, and the wheel and tire right below the new fender before painting. Cover the entire car with plastic sheets to stop overspray.
Use a wax remover with a solvent base to get rid of any grease, oil, dirt, and fingerprints before painting. There are probably minor handling blemishes in the primer that has already been sprayed on the fender. These must be removed with sandpaper, primed once more, and then lightly sanded over. Follow the manufacturer’s instructions while applying the basecoat. Spray the fender after lightly wiping the area to be painted with a tack cloth. Basecoats typically dry in under 30 minutes. Depending on the hue, you might need to use two or three coats to achieve sufficient coverage. Sanding between applications is strongly discouraged by the majority of paint manufacturers. Pay close attention to their advice, especially the one about using a respirator.
Following the completion of the basecoat drying process, combine the clearcoat and hardener per the manufacturer’s recommendations, apply a medium wet coat, wait for it to flash dry, and then repeat with a second coat. Remove all of the paper, plastic, and masking tape from the car after letting the clearcoat cure for a couple of hours.
A process called color sanding, followed by machine polishing, is used to eliminate dust particles and any orange peel or other flaws after the clearcoat has dried for a few days. Start by sanding the fender using 1500-grit sandpaper, keeping the area wet the entire time to clear away any dust. Avoid sanding around seams and folds to prevent sanding through the paint. Work steadily in small pieces until the entire fender has been sanded to ensure that you cover all surfaces. Look for any areas that are shining after properly drying the fender, as this suggests that additional sanding is required.
After sanding is finished, use a foam polishing pad and rubbing compound on a rotary buffing machine to enhance the paint’s sheen. Again, avoid rubbing through the paint by avoiding wrinkles and seams. By switching to a new foam pad and applying polishing compound again, followed by another pad change, another application of polishing compound, and then the application of speed glaze, you can improve the sheen and eliminate swirls. Wait a month before waxing when the job is finished polishing, then attach any final items.
The first CAPA fender that we bought online. But when we tried to put it on, getting it bolted up required a lot of bending, twisting, and choice words. When it was ultimately installed, it simply didn’t fit properly. We got a second CAPA fender locally (from a different manufacturer), and it fit exactly and was finished wonderfully. We were grateful that we hadn’t painted the fender before installing it.
For consumers who are dissatisfied, CAPA has a program to retrieve and replace parts. (To make a complaint, obtain the CAPA number from the label and dial 800-505-CAPA.) Purchasing the component from a trustworthy neighborhood parts store is a much faster option. So you can return the part and request a replacement if it doesn’t fit.
To assist users in providing their email addresses, this content was produced and maintained by a third party and imported onto this website. You might be able to discover more details on this and related material at piano.io.
What is the cost of replacing a fender?
We regret learning about your fender. Depending on the type of car you drive, front fender replacement expenses might range from $500 to $6,000.
You should expect to pay between $500 and $1,500 to replace a front fender, and between $1,500 and $4,000 to do substantial repairs. You might spend up to $6,000 if the repair is substantial, leaving the fender fully wrecked and making it difficult to operate your car.
Your fender can sustain damage even if you haven’t been in an accident. Watch out for these telltale symptoms that it might be time for a replacement:
- If your fender has visible damage like cracks or missing pieces, it could be time to repair it.
- Because of improper sizing, your tires will likely kick up debris and even harm your car’s body. Make sure to purchase the correct fender size for your car.
- UV radiation exposure results in stains on your fenders. This may diminish your car’s overall aesthetic attractiveness.
You’ll be happy you have the correct auto insurance if you wind up in a collision. Not protected? Jerry can assist!
Jerry is the quickest and best way to locate a car insurance plan that is specially tailored for you. A certified broker will provide you estimates from more than a dozen of the best insurance companies on the market right now in less than a minute. Jerry handles the rest when you’ve made your choice. They may even assist in modifying your old coverage!
How is a front fender replaced?
Wear protective glasses at all times when working on your car. When necessary, put on additional personal protective equipment (PPE), such as latex gloves or closed-toe shoes.
The fender liner retainers should be taken off. These retainers could be rivets, push-on nuts, clips, screws, or a combination of these.
The hood prop should be placed correctly after opening the hood. Remove any lighting that are affixed to the fender or the area around it. This could refer to the turn signal, park lamp, or headlamp assembly.
If a rocker molding is present, remove the front portion of it. This might be secured with screws, clips, or a combination of the two.
In order to reuse them on the new fender, take off any mud guards, moldings, rear shields, rear insulators, emblems, nameplates, or reflectors.
Check for more damage along the A-pillar and the apron behind the fender.
Reinstall any under-the-hood components, including the grille, headlamp assembly, battery, and upper radiator support.
How is an inner fender well removed?
One at a time, take off the fender liner retainers. To reach the plastic cap, use a flat screwdriver. Once you have turned the handle a quarter turn, the retainers will pop out because they are not threaded like screws. Proceed to the next one after prying off the plastic base with the screwdriver.
Can I change a fender on my own?
A damaged fender will cost a lot to fix. You might be thinking if you can replace the fender yourself because labor is so expensive. Compared to having a shop replace the fender for you, it would be much less expensive. But is the effort worthwhile?
The following variables influence the answer:
- Whether you possess the necessary tools
- If you have the necessary experience
- No matter if you can weld (applicable in a few situations only)
- Whether you have a few hours to dedicate to this task
Beginners should avoid attempting to replace a fender. So, if you have no experience at all with auto repair work, let professional auto body shop do it. For more details on this, skip to the post’s final paragraph. You might be able to replace a fender if you have some experience with auto repair. We’ll assist you in deciding whether you are capable of doing it.
How much time does a front fender replacement take?
The removal of the old fender and installation of the new fender will only take a skilled technician 35 hours. The paint job and curing, however, can add a few weeks to the overall replacement time.
How much time does it take to attach a fender?
Replacement of the Inner Fender Liner It’s a reasonably simple procedure that, on average, won’t take you more than an hour to replace your own fender liners. You can actually finish it in 15 minutes if you’re quick and have experience performing DIY auto repairs.