Directions
1) To remove the Front Panel from which I installed the USB Adapter next to the 12V 120W Socket, USB/Aux, follow the YouTube removal instructions. Taking out the radio is not necessary! – Regards, JPtheinstallguy
2) The rear console plate can be taken off by gently pulling it out. ONLY CLIPS, NO SCREWS! Clips are also used to secure the console side panel (driver). Pull gently. Inside the side panel, tuck the red wires.
3) Cut apertures for your USB Sockets on your panels using the tools at your disposal. CAUTION: Since the USB Adapters/Wires can conflict, it’s imperative to drill precisely and correctly. Before drilling openings, review. For it to work, you just have one attempt!
4) Attach the RED Wires with Female Spade Connectors on each end to each Positive + Terminal on the USB Adapter by wiring and crimping them. Take into account wiring slack!
5) Find an effective GROUND (Negative Connection). A VOM or multimeter is used to check for ground. Connect and crimp the BLACK Wire so that one end is connected to Ground with Ring Terminal and the other to each Negative – Terminal on the USB Adapter.
6) The Driver Side Is Where You’ll Find The Fuse Box (Underneath). Locate the 15A P/OUTLET fuse by removing the fuse cover. Cut the 15A fuse. The RED wire is crimped to the circuit fuse. Install (2) 15A fuses for each socket using the micro holder. Connect to the P/OUTLET fuse box.
If you want to solder the wires to spade and ring terminals, it is optional. It is advised to solder the wires/terminals outside of your car, on a workbench.
Directions
1) To remove the Front Panel, where I mounted the USB adapter next to the 12V 120W Socket, USB/Aux, please refer to the removal instructions on YouTube. Radio removal is NOT REQUIRED! – For your help, JPtheinstallguy >
2) Pulling out gently will allow you to remove the rear console plate. NOT A SCREAM, ONLY CLIPS! Also secured by clips is the console side panel (driver). Pull briskly. Insert the RED Wires inside the Side Panel.
Create apertures for your USB Sockets on your panels using the tools that are readily available. WARNING: Drilling must be done precisely and correctly since USB Adapters and Wires may cause interference. Examine before drilling apertures. To do it properly, you just have one attempt!
4) Connect each Positive + Terminal on the USB adapter with the RED Wires with Spade Connectors (Female) on either end. Consider wiring slack!
Find a strong GROUND (Negative – Connection). checking for ground with a VOM or multimeter. Connect the BLACK Wire with a ring terminal and crimp it to each of the USB adapter’s negative terminals. The other end should be connected to ground.
6) The fuse box is on the driver-side of the vehicle (Underneath). Find the 15A fuse for P/OUTLET by removing the fuse cover. Detach the 15A fuse. the RED wire to the circuit fuse with a crimp For each socket, tap the micro holder and insert a 15A fuse. Fuse Box P/OUTLET should be connected.
It is optional to solder the wires to the spade and ring terminals. It is HIGHLY RECOMMENDED that you solder the wires/terminals outside of your vehicle, on a workbench.
Complete Aftermarket Center Consoles
You can modify some free spaces in your vehicle by using aftermarket center consoles, which come in a range of sizes and designs. These typically sit on the ground or a chair.
For example, the Pilot Contractor Console can be placed immediately on a truck’s bench seat. These practical cabin modifications can be a good choice for you because many bench-seat cabins don’t have a central console at all.
Another illustration is the TSI Clutter Catcher Minivan Console, which fits in a minivan or SUV between the captain’s chairs. Adding a stand-alone aftermarket center console to the back row of your minivan might give additional passengers a front-row experience if you don’t need the extra room to move between the seats of the second row.
There are many different features available with aftermarket bench center consoles. The RAMPAGE PRODUCTS locking center console has two storage spaces with locks and cup holders for the front and back rows if you need more cup holders for your 19761995 Jeep Wrangler.