How To Program 2003 Toyota Camry Remote

Toyota / By

Five minutes are required.

  • Obtain Vehicle
  • Step 1: Enter Programming Mode

Complete the following actions in 5 seconds:

Step 2: Enter Programming Mode

DO the following things in less than 40 seconds:

  • Step 3: Enter Programming Mode
  • Step 4: Enter Programming Mode

SET the ignition to the ON position (DO NOT ENGINE CRANK) and then TURN IT OFF AGAIN. To keep the already programmed remotes and add a new remote, only do this ONCE. To ERASE ALL CURRENTLY PROGRAMMED REMOTES AND ADD NEW REMOTE, repeat this procedure TWICE. To VERIFY how many remotes are programmed to the car, repeat this process THREE times. To ERASE ALL CURRENTLY PROGRAMMED REMOTES, repeat this process FIVE times.

Step 6: Enter Programming Mode

Ignition key should be removed. When a person successfully enters programming mode, the power door locks will react by cycling between the locked and unlocked positions.

Setup the remote

Complete the following actions in 40 seconds:

a. Press and hold the remote’s LOCK and UNLOCK buttons for 2 seconds at the same time. RELEASE.

The car will react by cycling the locks from LOCK to UNLOCK to show that the remote was successfully programmed.

Programming Extra Remotes

REPEAT Step 7 to program any additional remotes, even functional ones.

  • Programming Mode EXIT
  • Try the remotes
  • Share

Please think about telling your friends and family about our website if these programming tutorials helped you save time and money so they can do the same.

Notes about programming:

  • Check the following before implementing these guidelines:
  • Keyless entry is available in your car, and
  • Your car is compatible with the key fob remote you have.
  • Securing EVERY remote transmitter for this car.
  • If your key has a transponder chip in the remote head, this process will ONLY program the remote part. The transponder key that will start the car must be cut and programmed by a professional auto locksmith.
  • This process WILL work for your car if you have a remote head key without a transponder chip.
  • For clever proximity remote key fobs, this technique DOES NOT work.

How can I set up my Toyota remote control manually?

How to Set Up a Toyota Car Remote

  • Within five seconds, turn your ignition key from “off” to “on” again.
  • Close and reopen the driver door twice in the following 40 seconds. Then, put the key in and take it out of the ignition once again.
  • Once more, make sure you finish steps 1 and 2 within 40 seconds.

How can I program the key to my 2004 Toyota Camry?

1. Start by turning off the ignition.

2. UNLOCK and OPEN the driver-side door. CLOSE the trunk and all other doors.

3. Put the key in the ignition and pull it out twice in the space of five seconds.

4. DOUBLE-CLOSE and DOUBLE-OPEN the driver-side door.

5. Turn the key in the ignition, then take it out.

6. DOUBLE-CLOSE and DOUBLE-OPEN the driver-side door.

7. Place the key in the ignition and keep it there.

8. SLIP the driver-side door shut.

9. Start the ignition and then turn it off.

10. REMOVE the ignition key.

11. The door locks will now cycle to show that the car has entered programming mode successfully.

12. When programming the first remote, PUSH and HOLD the LOCK and UNLOCK buttons for 1.5 seconds. As soon as you release, push and hold the lock button for two seconds.

13. To verify that the remote was successfully programmed, the door locks will cycle. Repeat steps 12 and 13 if you need to program any additional remotes. If not, move on to step 14.

14. OPEN the door on the driver’s side. The programming is now over.

Want a professional to configure the remote for you since you’re having problems doing it yourself? Find a qualified key fob installer in your neighborhood by typing your city or zip code in the search box below.

Was this Knowledgeable? Please consider making a gift of any kind to support this blog! Your contributions aid in the upkeep of this website. We appreciate your visit and donation.

Replace the batteries inside the key fobs

If you haven’t changed the battery in the key fob(s) in a while, do so now before continuing. When you try to reprogram a key fob with a defective battery, it can be a real pain. The batteries are often inexpensive and simple to replace. If you are unsure how to change them, consult your owner’s manual.

Get inside the car

With your car keys and the remote in hand, go in the driver’s seat and lock all the doors. Closing the doors is crucial because if you leave one open, it can disrupt the procedure.

Turn on the ignition

Once seated, turn the key to the “On” position in the ignition to turn the electrical systems on. Do not start the engine and double-check that the ignition is not in the radio mode.

Press the lock button on the remote key

Turn the key back to the “Off” position while holding down the lock button on the fob. At least three times, go through this process, finishing with the key in the “On” position. This notifies your electronic control units that the signal is coming from your key in the ignition and does save the info later. How to Start & Unlock a Car With a Dead Key Fob

Listen for a Lock Sound

You will hear the lock sound once you have completed the aforementioned steps. You have now accessed the programming mode, as indicated by this. Press the lock button once more in the following five seconds to complete the programming.

Programming additional remotes

If there are other remotes, program them successfully by pressing the “Lock” button within 10 seconds after entering the programming mode.

Step out from your car and test the result

Close all doors as you exit the vehicle and take your key fobs with you. Test the functionality of both unlocks with each of your key fobs that were programmed.

Step 3: Cycle the Ignition

Put your key in the ignition and hold down the “UNLOCK” button on your door. We will now turn the ignition on and off twice. Please take note that we are merely turning the key one notch to power the electrical systems, not starting the car.

Step 5: Hold Down the “UNLOCK and “LOCK Button on Your Fob

Press and hold the “LOCK” and “UNLOCK” buttons on the key fob simultaneously until the locks cycle one more to program your keyless-entry remote. Please be patient as this could take up to 30 seconds.

Can I set up any remote control for my car?

I’m here. As long as the key is the same for each vehicle, you can reprogram a key fob to work with that vehicle. In this situation, if the key can open the doors, you would need to take the following actions:

  • The key fob’s battery should be removed and then replaced (unless you put in a new battery)
  • After unplugging the vehicle’s battery wires, wait 30 seconds, then reconnect them (reset computer).
  • Turn the key to the ON position after inserting it into the ignition.
  • In the OFF position, turn the key.
  • Locking the door simultaneously with your hand and the remote requires turning the key to the ON position.
  • While simultaneously using the remote and your hand to unlock the door, turn the key to the ON position.
  • Remove the ignition switch’s key.
  • the driver door with the key.
  • Push the lock and unlock buttons on the key fob simultaneously with locking and unlocking the door with the key – (do this 3 times).
  • Try using the remote to unlock the doors while the door is closed after taking the key out of the lock.
  • Put the key in the ignition switch and attempt to start the engine if the doors will lock.

After completing these procedures, the key fob has been successfully reprogrammed to your car if the engine starts. If the key does not lock the doors or start the engine, it may be completely different, and you will need to get a new key. Seek out a specialist, like one from Your Mechanic, if you require more help with your keyless entry system.

How can my Toyota remote be reset?

It can be very annoying to have a broken key fob, but hopefully reprogramming the key will get you back on the road!

Reprogramming a Toyota key fob involves:

Keeping all other doors closed and the key off the ignition, start by opening the driver’s side door.

Step two is to twice insert and withdraw the key from the ignition without turning it within five seconds.

Step three: Close and open the driver’s side door twice within 40 seconds. Without twisting the key, insert and remove the key from the ignition.

Step 4: In the following 40 seconds:

  • The driver’s side door is closed and opened twice.
  • Keep the key in the ignition after inserting it.
  • Lock the door on the drivers side.
  • Without starting the engine, switch the ignition from off to on.
  • The ignition key should be removed.
  • Step five is: The doors should automatically lock and then unlock after three seconds to signal that you are in programming mode. If the doors do not lock and unlock on their own, go back and repeat steps one through four.
  • Step six is: 40 seconds after switching to programming mode:
  • On the remote, simultaneously press and hold the lock and unlock buttons for less than two seconds before letting go.
  • For two seconds, press and hold the lock button. To demonstrate that the key was successfully programmed, the doors should automatically lock and unlock.
  • The key was not successfully programmed if the doors lock and unlock twice, so you must repeat the previous two stages.
  • Step seven is: Driver’s side door, open.

You will need to order a replacement for roughly $200 if the aforementioned measures don’t work, which is pricey. Use Jerry to reduce the cost of your auto insurance if you want to save some money.

Jerry will handle the phone calls, paperwork, and renewals for your top option after giving you a thorough cross-analysis of the best plans from over 50 providers so you don’t have to. They even assist in removing your old insurance.

Why doesn’t my automobile recognize my key fob?

The most frequent cause of a keyless entry system failing to send signals is a faulty battery in the key fob. Use the extra key fob to unlock the car and turn on the ignition if one is available.

Use the key that is included in the spare fob if it is not available to unlock the door. Check your owner’s manual for information on how to start your automobile when the key fob malfunctions.

What is the cost for Toyota to program a key fob?

Visit your neighborhood Toyota shop or use a mobile vehicle locksmith in Maricopa, Arizona, to obtain a replacement Toyota Smart Key.

Toyota Smart keys will run you anywhere from $260 to $400, including programming and key cutting. Get an Instant Estimate depending on the location, year, and model of your Toyota.

Yes! Although most of the time the cost of the key is negligible in relation to the expense of programming it, if you purchased a spare key online, you can contact a local auto locksmith to do it for you.