Until the day you put the key in the ignition and it gets stuck, your Toyota Corolla normally runs like a dream. The key simply won’t budge no matter how much you twist and jimmy it. You know you can’t keep your automobile in this condition, but you’re also unsure of what to do. How is the key removed from the ignition?
Although it varies from model to model, the following steps should help you remove your key from the ignition of your Toyota Corolla:
- Make sure you are in park.
- Verify that nothing is blocking the steering column’s locking.
- Check to see whether the key comes out by cutting off the electricity to the solenoid.
- Check to see whether your car’s battery has died.
- Test the ignition lock cylinder and the lock mechanism.
- Get a tow.
- Visit a mechanic with your vehicle.
In This Article...
Make Sure You’re in Park (parking mode)
Are you sure you’re in park? I know that sounds dumb and very, very common sense. If so, the automatic transmission in your car probably won’t let the key out unless you put it in park mode. The shift interlock, a safety mechanism, is to blame for this.
Wriggle Your Steering Wheel to Get the Locking Steering Column to Release the Key
Most cars have a locking steering column as an option. Once you take the key out of the ignition, it will lock up. That is intended to deter car thieves. If the locking steering column malfunctions, excessive pressure is applied to the ignition switch, which keeps the key in the Corolla locked.
You can get your key while your vehicle is in parking mode by turning the steering wheel.
Disconnect the Power to the Solenoid
Don’t worry if the aforementioned suggestions haven’t worked thus far. Sam Carmel, the proprietor of Corolla, claims in a “>YouTube video that the starter solenoid found in Corolla vehicles may hold the key (no pun intended) to resolving your problems. This solenoid activates the starter motor of the car by acting as an electromagnet. Two lengthy cables from the starter solenoid connect to the starter motor.
By cutting the wires, you should be able to turn off the solenoid. In the 2010 Corolla, at least, where Carmel focused for his film, the solenoid is located behind the steering wheel. He claims that modifying the solenoid is secure. Hopefully, that will produce the key.
Test Your Car Battery Life
Your Corolla can’t operate without power if the entire interior, including the ignition, is electronic. That usually means that if your automobile battery dies, your key could become seized. There are two clear signs that the problem is with the battery. Do you first notice any inside lights? Can you also start the car?
If the response to either of those two queries was no, your battery has likely died. If you’re not at home, you’ll need to acquire a jump. In order to avoid getting into another awkward situation, make sure you monitor your car battery in the future.
Confirm Your Ignition Lock Cylinder Is Properly Working
A device known as an ignition lock cylinder is found in many vehicles. This is arranged in a row with many pins. When you insert the key into the ignition, a spring inside each of these pins can be released, holding the key in place.
These pins are far from flawless, much like every component of a car. Your key won’t come out of the ignition if there is misalignment or if any of the pin springs become stuck and unable to retract. Smack your ignition lock cylinder with a small hammer, but do so very carefully. After all, you don’t want to damage it. With any luck, a few solid blows will get everything going. If not, a new ignition lock cylinder is probably in order.
A clean ignition lock mechanism is also important. You might have trouble getting your key in or out smoothly due to gunk and particles.
Call a Tow/See a Mechanic
In the worst-case scenario, you might need to call a tow truck to have your car towed and yourself sent home (or work or wherever you were going). If you tried all of the aforementioned fixes and they had no effect, then that is. Most likely, there are deeper issues at play than you can address on your own. Allow a mechanic to handle it.
My Toyota key is stuck in the ignition; why is that?
It’s likely that you inserted the wrong key if your key is stuck in the ignition and the steering wheel of your car is also locked in place. Most cars include a safety mechanism that locks the steering wheel in case the wrong key is inserted. Turning the steering wheel slowly to the left and then to the right while lightly pressing the key will quickly fix this. As soon as you apply sufficient force, you ought to be able to unlock the steering wheel and take the key out of the slot.
Why won’t my key eject from the ignition?
Most often, a broken or worn-out vehicle key or faulty ignition wafers are to blame for a car key that is stuck in the ignition and won’t come out.
The following are the three most frequent causes of stuck car keys:
- broken car key Car keys can get broken, worn out, and bent, which makes them stuck.
- Broken Wafers
- The wafers that make up your car’s ignition can bend or break, which results in a jammed key.
- Driving Wheel Lock
- The ignition may lock simultaneously with the steering wheel lock if the steering wheel lock malfunctions.
Why is the key in my ignition stuck?
We’ve worked on enough ignitions to be aware of potential problems. Among the most typical issues are:
- The steering wheel lock is one of the most likely causes of a stuck ignition key. The steering wheel may lock when a car is in park. This is fantastic for preventing theft, but it also stops the key from turning or being taken out of the ignition switch. Sometimes the issue is not with the ignition or the car. It can be a key that has become worn or broken and been stuck in the ignition switch. Pulling or yanking on the key may make it more difficult to remove and may seriously harm the ignition.
- Before beginning an ignition repair on your automobile, double-check that you’re using the right key for the right vehicle and check the key for any damage. We’re not calling you stupidwe’d never do that! Continue reading if you’re positive that the ignition is the source of the issue.
How can I remove my car’s keys?
The usage of fancy key fobs, touchpads, and remote-unlock sensors in some more recent vehicles virtually ensures that you won’t get locked out. But what about the millions of poor souls who still manually lock and unlock their vehicles? Will they always be bothered by automobile windows that are shattered and prybars?
It is entirely possible to get your keys out of a locked car with a little patience, experience, and even more patience, and you probably won’t need to go to an auto body shop nearby to have your window fixed afterward. Here are some pointers for entering your locked automobile safely. (Bad people shouldn’t read any farther.)
How can I get my 2021 Toyota Camry’s key out?
Try pressing the brake pedal and shifting between park and neutral while moving the gear shift lever. steering wheel movement is also somewhat made. All of this should be done while turning and pulling the ignition key.
How do you use a key to start a Toyota Corolla?
Using the Push-Button Start on Your Key Fob To start the engine, simply depress the brake pedal, make sure your key fob is in your pocket, and press the Start/Stop button. When you get at your location, just put your Toyota in Park mode and depress the button to turn the engine off.
How can I remove my dead car keys from the ignition?
How to Remove an Ignition-Stuck Key
- Recharge the vehicle’s battery.
- Putting the shifter in park.
- Get the steering wheel unlocked.
- Give the lock a lubrication spraying.
- Ignition jiggling
- Check the error codes.
- Check the push key and safety switch.
- Contact a repair shop.
My Toyota Camry key won’t turn; why?
The most frequent causes of a Toyota Camry key not turning include a locked or binding steering column, a malfunctioning ignition switch, or a fault with the ignition key.
How much does it cost to retrieve your car keys?
Many consumers buy roadside assistance through an auto club, a credit card company, or as supplemental coverage on an auto insurance policy for peace of mind.
How do you remove the Toyota Camry’s keys from the trunk?
If you try this procedure on your own, there’s a risk you won’t be able to put everything back in its proper place, so be sure to follow the instructions and watch the instructional video first. When your Camry’s doors can be unlocked but the alarm system prohibits you from opening the trunk and your keys are inside, it still functions.
- On the driver’s door, find the plastic plug. When the door is closed, it is level with the handle and faces the B-Column. Remove it, then store it securely.
- Peer through the gap.
- Inside is a Torx head screw. Locate the right size Torx screwdriver, then remove the screw. Although there are safeguards in place to stop the screw from hitting the door, proceed with caution just in case.
- To get to the key cylinder, pull the door handle. The key cylinder must be removed from the socket, however doing so can be challenging due to how tightly it fits. Avoid breaking off the handle or scratching the paint. As a temporary layer of security, some masking tape will be fantastic.
- The cylinder head will emerge facing the car’s rear. Once you’ve opened the trunk, you won’t be able to put it back in any other way, so keep this in mind.
- Take a look at the key cylinder’s tip. The plus-shaped lock mechanism will be visible. When you look inside the cylinder slot, you will see a plus-shaped indentation where the cylinder should fit.
- Carefully place a flathead screwdriver into the cylinder slot. Rotate it to lock the car and then to unlock it once it is positioned inside the plus-shaped indentation.
- When you push the trunk release button, the trunk instantly opens!
It is far more difficult to put the cylinder lock back in place than it was to remove it. Let’s follow the procedures to put the door back in working order.
- Slide the cylinder back in from the same angle it was inserted by raising the door handle. Take your time, be gentle, and avoid using forcethis will involve plenty of twisting, pivoting, and turning.
- Insert the key, turn it, then gradually apply pressure to the cylinder until it is facing the proper direction and the door handle can slide onto it. The cylinder should then automatically fall into position.
- Tighten the Torx screw while the key is still within the lock. If the screw isn’t holding, you’ll use the key to wriggle it into place until it does, causing everything to settle into its proper position.
- After replacing the plastic stopper, the procedure is complete.