This step-by-step manual is based on Sienna models from 2011 and after. If you have an older Sienna model, you can still try to follow the instructions, but they might not be correct.
Here is how to replace the side door cable assembly in your Sienna without further ado:
- Remove the seat that is most near the broken sliding door. (Optional; it merely provides you with extra space to work on the door.)
- The window on the broken door should be rolled down.
- A hex screw keeping the plastic panel in place is located on the side of the door. Get rid of the screw.
- Reposition the lock so that it is in the open position. (This stops the lock from coming out when the plastic panel is removed.)
- Pry the plastic panel off gently. The panel is held in place by tiny white plastic retaining clips. Make every effort to properly pop them out.
- Pull off the entire plastic panel after closing the door (while still inside the van). Reach behind the panel and unplug the power window connector before you can remove it entirely.
- Once outside, turn your back on the door and lower the window. There is a window molding there. Pull out the window molding after prying off the clip holding it in place. To get it out, you might need to move it back and forth.
- Go to the quarter window in the back. The side door cable is hidden beneath the window by a plastic cover. Pry it away.
- Slide the cable assembly out of the bracket after removing the nut that was keeping it there.
- Three bolts inside the door hold the cable arrangement in place (where the cable makes a right angle turn). Remove each of the three bolts.
- Two additional bolts are located underneath the arm that holds the door to the van body. Take them both out. Removing these bolts might be challenging due to the constrained space underneath the arm. Use a 10mm ratchet, an impact driver, or an extension arm for the best results.
- In the bottom corner of the door, there is a pulley system with a Sienna side door release actuator. (The pulley system is in the bottom right corner if you are working on the right door; the bottom left corner if you are working on the left door.) All of the screws keeping it in place should be removed.
- the side door cable assembly should be slid out.
- Reverse the removal process when installing the replacement side door cable assembly.
In This Article...
What does it cost to replace a door on a Toyota Sienna?
Cost estimation for replacing the power sliding door motor in a Toyota Sienna. Between $1,589 and $1,661 is the typical price range for a Toyota Sienna power sliding door motor replacement. Between $276 and $348 is projected to be spent on labor, while $1,313 is the cost of the parts.
How can you unlock a jammed sliding door on a Toyota Sienna?
You may be wondering, “Why the heck is this happening? ” when your Sienna side door refuses to open or close.
Several such causes come to mind:
Latch Motor Failure
When you push the button to automatically open the side door, it could occasionally be difficult to open. It frequently makes noise while attempting to open but ultimately failing to do so. The door can only be opened by pulling the handle and holding it for two to three seconds.
This occurs when the latch motor malfunctions, which affects Toyota Siennas pretty frequently. Fortunately, changing merely the latch motor is a quick and affordable fix.
Circuit Overload
A circuit overload is one possibility if your Sienna side door won’t close. When the power sliding door can’t properly latch on, this occurs (due to something blocking it). The circuit for the electric motor will overload, trip the fuse, and prevent the door from fully closing.
You should start with diagnosing this problem because it’s rather simple to do so. Just check to see if the upper and lower tracks are blocked.
My Toyota Sienna is beeping, why?
The dash camera, faulty seatbelt sensors, loose electrical connections, low keyfob battery, low tire pressure, poor door latches, a malfunctioning rack and pinion, or one of the driver aid systems are the most typical causes of beeping on a Toyota Sienna.
While moving or parked, the following beeps could sound:
Check Everything is Shut Properly.
The vehicle will beep if any doors, the back hatch, or the hood are not correctly closed.
Even though it might seem obvious, it is advisable to confirm all of these before moving forward.
Spare Keys Left in Vehicle
If you have an extra set of keys in your Sienna, it may beep at you when you go to lock the car because it believes you are trying to lock the keys inside the van.
Dash Camera
You’ll probably hear this beep at startup if your dashcam was installed by Toyota at the factory.
If you look behind your rearview mirror, where the dashcam is positioned, you will see the dashcam blinking, but you won’t see any warning lights appear on the dashboard.
You could realize the micro SD card has not been fully inserted into the camera if you see an error flash.
Press and hold the “action” button while turning on the van if the SD card is in but still blaring.
- Ensure that the car is totally turned off.
- Make sure your parking spot is level.
- Verify that the camera is turned off.
- Keep holding down the action button.
- then drive off in your car
Loose Connection:Seat Belt Sensors
It is important to inspect the plastic wire connectors under each seat in the car to make sure they are all tightly fastened.
Seatbelt Alarm& Weight on Seat
Your seatbelt’s fastening may not be detected by a sensor because it is malfunctioning.
As an alternative, you might have a bag of groceries or other weight on the passenger seat that is setting off an alarm.
BSM
When you start to reverse, the Blind Spot Monitor should flash a warning light in your rearview mirror and emit a beeping sound to alert you to the presence of someone in your blind spot or if they are approaching from behind your car.
Faulty Switches
The beeping could be caused by a broken ignition switch or a broken headlight switch.
One of these switches may have a loose connection or be malfunctioning since the chime will only play when the headlights are on or the key is in the ignition.
Without a key, how do you unlock a Toyota Sienna?
I’m sorry you’ve locked yourself out! Even the best of us experience it. Fortunately, Toyota Sienna models made in 2017 and later come with a technology that prevents lockouts.
Grab the handle on your driver’s side door to turn this function on. On the interior of the handle, there ought to be a sensor. The automobile will open the door for you once it detects your fingerprint.
Having stated that, you will have to have pre-programmed this feature. If not, call a locksmith for assistance getting back into your car. You can receive a replacement car key as well as same-day emergency services from a locksmith to get back into your locked automobile.
To obtain an additional key, you might also try contacting your local Toyota dealership or repair facility.
Make sure you’re ready for any eventuality once you’re back in your car by using the Jerry app.
Jerry is a private auto insurance agent who resides in your wallet. After you download Jerry, simply respond to a few questions that should only take you 45 seconds to finish, and you’ll have car insurance rates for the coverage you require right now. Customers of Jerry save $887 year on average.
Can sliding glass door tracks be oiled with WD40?
It is necessary to check, clean, and lubricate the upper roller and the door track that it is connected to. It’s crucial to occasionally adjust patio doors. With a screwdriver, remove the upper door coverings that conceal the sliding system on both sides of the door to gain access to this mechanism. To get rid of dirt, dust, and other debris, use a vacuum cleaner. Apply WD-40 Specialist Long-Lasting Grease Spray next, allowing the dense, quick-acting formula to provide long-lasting lubrication along the sliding door track, wheels, and rollers. It doesn’t drip and stays fastened to the base. It lessens friction and makes it easier for any moving metal parts to function. It is also perfect for metal parts that cannot be regularly greased. Reapply the upper covers once you are satisfied with the lubrication of the patio door tracks. Use enough soap, a vacuum, and some blotting paper to remove any tracks that are ingrained in the floor.
Lubricate Accordion Door Tracks
These doors gather on the side of the entryway rather than fitting into a hidden shell. Accordion doors’ panels can have different thicknesses. They are made of internal perimeter frames formed by special profiles in galvanized steel 20/10 thick or drummed steel, and they can also be completely smooth or have surfaces that resemble wood, with no visible joints or welding points. The coating of the outer surface is made of smooth sheet 8/10 thick that has first been hot-dip galvanized and then undergone additional treatments. The cleaning and lubrication procedures to be carried out are the same as those already mentioned because the sliding mechanism is comparable to those of sliding doors. Applying WD-40 Specialist Long-Lasting Grease Spray along the hinges of the different door segments might be helpful since it makes movement easier and keeps the joints clean.
Lubricate Overhead Doors
A common style of sliding door that can be operated manually or electrically is an overhead door. They have a number of joints, rotation, and lifting mechanisms, all of which are often accessible. WD-40 Specialist Fact-Acting Degreaser, which eliminates old grease that has been combined with dust and other foreign objects, may be needed as a preventative measure on these parts. Then apply WD-40 Grease Spray to lubricate.
Lubricating Corner Sliding Doors
Sliding door systems can be created to meet in a corner at two different heights, just as dual threshold door systems. As a result, moving the doors back enables for the display of an open-angle setup without any discernible corner posts (models with static corner posts are also available). In these situations, it’s crucial to lubricate the track sliding guides in accordance with the previous instructions.
Why does my automobile keep beeping?
Your car’s beeping is an indication that something isn’t right. While some of these problems may be simple, others could need the assistance of mechanics. Let’s look at each of these in turn below:
Unbuckled Seat Belt
The most frequent cause of an automobile beep is an unbuckled seatbelt. The vehicle is attempting to alert you that this feature is inoperative.
Rebuckling the seat belt can be all that is necessary to resolve this problem. Before utilizing the vehicle once more, the buckle must be changed if it appears to be broken.
When you are the only person in the car and the unbuckled seat belt light starts to beep, there may be something heavy on the seat. Check to see what is causing the light to be on.
Open Door
Another frequent cause of your automobile beeping is an open door. After being opened, the automobile will continue to beep for a short while.
This can happen when a door is left partially open or not completely closed. This might happen, for instance, if the door was opened accidently or ran into something else. It may only take closing and locking the door once more to resolve this situation.
Open Trunk
Another common cause of your automobile beeping is an open trunk. After being opened, the automobile will continue to beep for a short while.
This can happen if the trunk is not completely closed before restarting the car or is left open. Re-closing and locking the trunk may be all that is necessary to resolve this problem.
It’s also conceivable that the trunk door latch is damaged, making it impossible for the trunk to close all the way. If so, it must be fixed or replaced before the vehicle can be used once again.
Open Hood
Another frequent cause of your automobile beeping is opening the hood while it is running. This can happen if someone leaves the hood open or forgets that they left it open in the past.
Simply closing the hood once again will solve this problem. The hood latch will need to be changed, though, if it appears to be damaged. The last thing you want to happen while driving is for your hood to fly open.
Electrical Issue
Another reason your automobile may beep randomly is due to an electrical problem. When the battery is running low or there is another electrical issue, this will happen.
This issue could also be brought on by the possibility that your car’s alarm system was activated. In either scenario, it will need to be examined by a reliable mechanic.
Low Coolant Levels
Your automobile beeping may occasionally be caused by low coolant levels or other engine overheating problems. This can be the result of an engine issue or a low coolant level. To avoid doing serious harm to your engine, have this examined by a mechanic.
The Parking Brake is on
Your automobile may still have the parking brake engaged if it beeps when you put it in drive. This may happen if the parking brake is accidentally or habitually engaged.
To avoid major harm to your back brakes and other parts as a result of this problem, this will need to be examined by a mechanic.
Lights are on
Your automobile may beep as a result if your headlights are still on. This happens as a result of the sensors checking to see if the lights are on and beeping when this function is on.
To resolve this problem, you can either turn off or set the headlights to AUTO. Disconnecting the battery is an additional choice because it will instantly reset all of your electrical equipment and deactivate any alarms that may have been triggered.
Faulty Security Immobilizer
Your car’s security immobilizer or anti-theft system could be broken. To avoid any harm from developing as a result of this problem, this needs to be checked by a reliable mechanic.