As part of routine maintenance, cleaning the MAF can help to lessen and/or prevent these issues. Cleaning the MAF sensor can help and frequently can solve the issue if it is that sensor that is malfunctioning. You can carry out this at home. Simply pull the part out, clean it, and then put it back on your engine’s air intake system.
In This Article...
How should a mass airflow sensor be cleaned?
The first rule is to NEITHER clean the MAF sensor while the engine is running nor even with the key in the run position. The sensor may sustain severe damage as a result. Unplug the sensor when the key is off.
Put a towel behind the MAF sensor to capture discharge. Spray the inside of the housing with ten to fifteen bursts after inserting the plastic straw into the can’s nozzle. The plate and any hot wires need to be covered. Make sure that nothing, not even the straw, touches the wires. The wires are quite fine.
Before starting the engine, reinstall the sensor in the vehicle and wait a short while for the chemicals to evaporate.
Every time you replace or clean the air filter, it is a good idea to clean the MAF sensor as well. 410 horsepower can be restored to the wheels with a clean MAF sensor, which is a considerable amount for simply cleaning a sensor.
On Karman-Vortex style air flow sensors, which are generally found in Toyota Supra turbos, Mitsubishi (including the DSM rebadged Eagle Talon and Plymouth Laser), and the majority of Lexus engines, DO NOT USE ANY MAF sensor cleansers. These unique Karman-Vortex sensors have extremely delicate parts that cannot be cleaned since doing so could seriously harm the MAF sensor. A Karman-Vortex style air flow sensor cannot be cleaned effectively by a do-it-yourselfer. Just let it be when in doubt.
Be sure to get in touch with your neighborhood NAPA Auto Parts Store or NAPA AutoCare Center if you have any reservations about handling this chore yourself.
If you need routine maintenance and repairs, turn to one of our 17,000 NAPA AutoCare facilities or browse all the chemical and lubricant items on NAPA Online. Speak to a trained specialist at your nearby NAPA AUTO PARTS shop for further details on how to clean your MAF sensor.
How can I tell if my MAF is contaminated?
Seven Symptoms That Your Mass Airflow Sensor Is Bad Or Dirty
- Red Exhaust. The black exhaust from too much fuel is one indication that your car’s MAF is failing.
- Engine check. A malfunctioning mass airflow sensor is frequently the blame for an illuminated check engine light.
- Trying Starts.
- Hesitation.
- Low gas prices.
- Rusty Idle.
- difficulty accelerating
Can I remove the MAF sensor and still clean it?
An engine that starts difficult, runs rough, and may or may not maintain a correct idle are signs that the mass air flow sensor (MAF sensor) is unclean. The MAF sensor in your car measures the volume of air entering the engine. This measurement is used by your engine control unit (ECU) to calculate how much gasoline the engine requires. For optimal performance, your MAF sensor has to be clean.
Before wasting time and money diagnosing other problems or replacing more expensive parts, it’s a good idea to try cleaning your MAF sensor. This simple remedy just requires a can of MAF sensor cleaning and the tools required to loosen your MAF sensor. View our mass air flow meters for sale here if all else fails.
Locating Your Vehicle’s MAF Sensor
You already know where to look for your vehicle’s MAF sensor if you’ve ever changed the air filter in it. On the intake system of your car, there is a medium-sized plastic box where the MAF sensor is located. It’s possible for your MAF sensor and air filter to share a housing.
If you’re having difficulties finding your MAF sensor, you can utilize Google Image Search to locate it by using a search word that is specific to your vehicle’s year, make, and model.
Loosening or Removing Your MAF Sensor
In many cases, cleaning the MAF sensor does not need removing it from the car. When performing maintenance or repairs on your car, stay away from removing and dismantling parts that aren’t necessary. To avoid going too far with the disassembly process, try to plan ahead.
TORX screws or other unusual fasteners could be used to secure your MAF sensor to your car. Before you start the repair process, make sure you have the appropriate tools available. To make sure you have the correct tools to work on your car, it is usually helpful to conduct some research beforehand.
Before exerting any effort on your tools, be sure they fit the fasteners on your car. By doing so, you’ll be able to avoid stripping or rounding off the fasteners as you carry out the required upkeep and repairs.
Cleaning Your MAF Sensor
Grab your can of MAF sensor cleanser and spray it within the housing once you have access to your MAF sensor. Aim for the flapper door or the wire element that are located in the centre of the MAF sensor. To avoid using more cleaner than necessary, spray quickly.
Never try to clean or polish the MAF sensor’s components. They are brittle and simple to harm. The MAF sensor cleaning can’s force ought to be more than sufficient to clean the components.
When working on your car, it’s a good idea to wear gloves, long sleeves, and safety eyewear. Because they are corrosive, automotive solvents can irritate your hands, eyes, and skin.
Check Your Results
Reassemble the air intake system on your car. Launch the car. After you’ve cleaned the MAF sensor on your car, it should start readily and run without any issues.
You might need to repeat the MAF sensor cleaning procedure if the car won’t start readily or operate smoothly, or you might need to run more diagnostic tests to find the real source of the issue.
Can you clean a mass air flow sensor using rubbing alcohol?
The Mass Air Flow (MAF) sensor in your car can be dirty if it isn’t running as smoothly as it once did. Numerous problems, including reduced fuel efficiency, rough idling, and even engine stalling, may result from this.
Fortunately, cleaning the MAF sensor is a rather straightforward procedure that can be carried out with a few basic tools that you probably already have at home.
By following a few simple procedures, you can clean your MAF sensor: Use pressurized air to blow any dirt or debris off the sensor. By placing alcohol on an ear stick, gently wipe the sensor while using isopropyl alcohol. To remove any dirt or grime, just moisten it with the solution and wipe.
In just a few simple steps, we’ll demonstrate how to clean the MAF sensor with alcohol in this blog post.
Why does unplugging the MAF make my car run better?
Your investigation into the root of the engine’s poor performance led you to the mass airflow sensor. The car appears to operate more smoothly without the MAF sensor than it did with it. How come this is the case?
If the MAF sensor is producing erroneous readings and the car runs better without it plugged in, the sensor needs to be cleaned or replaced.
You should read the post after this one because I’ll explain how the MAF sensor functions, why it’s crucial, and why you shouldn’t drive without one, even if the car is running better, without it.
What damage might a filthy MAF sensor do?
Your car may have poor driving characteristics due to a faulty MAF sensor, like stalling, jerking, or reluctance when accelerating. This may occur as you’re driving quickly down a city street or on a motorway onramp. These problems may result in hazardous conditions that result in mishaps and injuries.
Clean the MAF sensor
Spray the wire or plate with 10 to 15 spurts of the (MAF) mass air flow sensor cleaner.
A Mass Air Flow (MAF) sensor is what, exactly? The temperature and volume of air entering your engine are both monitored by a MAF sensor. This data is required by your onboard computer to determine the appropriate fuel dosage for all engine running scenarios.
The sensor functions by heating a thin platinum wire or plate and determining the current needed to maintain its temperature while air is being forced past it. Dust and oil stains build up over time on the hot wire or plate. Eventually, the wire/plate becomes airstream-insulated thanks to those baked-on particles. As a result, there are issues with starting, idling, acceleration, and gas mileage.
At that time, automakers like Ford and Chevrolet advise replacing the MAF sensor ($300). But if you periodically clean your car’s MAF sensor, you can save $300 in repairs and maintain peak engine performance. Mass air flow cleaner prices start as just $7! Every time you replace your air filter, we advise cleaning the MAF sensor. This is how:
Check how the MAF sensor is fastened before heading to the store by removing the air duct that runs between the air filter box and the throttle body. Buy a Torx tool and a can of CRC Mass Air Flow Sensor Cleaner if you encounter Torx screws. Use only these cleansers; all else will damage the MAF. The car parts shops at CarQuest, Advance, and O’Reilly provide everything you need.
Locate the MAF sensor in the air duct that runs between the air filter box and the throttle body while using the mass air flow cleaner and other necessary tools. Use a camera to take a picture of the sensor’s setup and connections before you remove it for future reference. Remove the electrical connector from the sensor before carefully removing it from the air duct.
Spray the wire or plate with 10 to 15 spurts with the mass air flower cleanser. Avoid cleaning the components; doing so could break the wire or harm the plate. Prior to reinserting the MAF sensor in the air duct, give it time to fully dry.
Required Tools for this Mass Airflow Sensor Project
You’ll save time and hassle if you have all the tools ready before you start this DIY project.
four-in-one screwdriver
What signs would point to a damaged mass air flow sensor?
Signs of a Malfunctioning Mass Air Flow Sensor
- It’s quite difficult to turn the engine on or off.
- Not long after starting, the engine stalls.
- While running at idle or under load, the engine hesitates or lags.
- acceleration with jerks and hesitation.
- The engine bogs down.
- Lean or very rich idling
How can I tell whether my mass airflow sensor is functioning properly?
If your car has been having issues with poor idle or intermittent faults:
- Put the parking brake on.
- Set the automated park or neutral position on the transmission (manual).
- Idle the engine after starting it.
- Open up the hood.
With the handle of a screwdriver, gently touch the electrical connector and MAF sensor. Additionally, wiggle the wires.
- The MAF sensor is probably faulty if the engine stalls, the idle is disturbed, or the idling improves.
If the engine struggles to idle or won’t start:
- Unplug the electrical connector for the MAF sensor.
- Replace the MAF sensor if the engine starts or the idle gets better.
How durable are MAF sensors?
The mass air flow sensors in your car are built to last a lifetime. In actuality, there is no set time between replacements. The sensor is typically not replaced until it fails because of this. Your mass airflow sensor should last for at least ten years, although this can change based on a number of things.
As impurities like carbon over time accumulate inside the mass airflow sensor, it becomes more difficult for air to move through. Engine performance issues will result from the sensor’s inability to effectively gauge the engine’s air levels due to the reduced air flow.