Depending on your degree of competence and whether you’re working on two or four wheels, replacing the brake pads on your Highlander could take anywhere from one to four hours. Here’s how to do it effectively and safely at home:
- Put the parking brake on.
- The lug nuts on the wheel you’re working on should be loosened.
- Safely jack up or lift your Highlander.
- Take one of the wheels off.
- On the caliper’s side, unbolt the sliding bolts. Make sure to not touch the mounting bolts.
- The brake line mounting bracket’s 12mm bolt must be removed.
- The brake pads are visible if you pull back the caliper.
- The brake pads should be gently pry-out with a flathead screwdriver.
- Make that the brake pads are being worn evenly by inspecting them. If they aren’t, your rotor or caliper may be malfunctioning.
- Eliminate the dust inside the caliper and piston by brushing or wiping it away with an old toothbrush or rag.
- Utilizing a clamp or caliper compression tool, push the caliper piston back until it has bottomed out.
- Insert the fresh brake pads. The caliper has grooves that are intended to retain the pads in place. Simply locate these grooves, then insert the pads.
- Re-raise your caliper.
- After using a rag to clean them, lubricate the sliding bolts with brake caliper lubricant.
- Reinstall the sliding bolts, then tighten them.
- Reattach the brake line with the 12mm bolt.
- Use the lug nuts to reinstall the wheel.
- With the opposite wheel, repeat the operation (s).
In This Article...
How much do Toyota Highlander rear brakes cost?
Depending on the type of brake pads used and how much damage your old, worn-out brake pads did to the backup sections of your car, including the rotors, the cost to replace the brake pads on a Toyota Highlander can range from $150 to $300 each axle.
How are Toyota brake pads installed?
How to Replace Brake Pads in a Car:
- Step 1: Lift your vehicle. Before changing the brake pads, you must lift your automobile off the ground and remove the tires.
- Remove the caliper assembly in Step 2.
- 3. Replace the brake pads.
- 4th step: swap out the caliper assembly.
- The Finishing Touches, step 5.
How much does a Toyota Highlander’s brake replacement cost?
Depending on the type of brake pads chosen and how much damage your old, worn-out brake pads did to your car’s specific parts, including the rotors, replacing the brake pads on a Toyota Highlander can cost anywhere between $150 and $300 each axle.
How are brake pads checked on a Toyota Highlander?
Give your brake pads the eyeball testreally it’s that easy. The eyeball test entails physically checking the brake pads to determine their level of wear after removing the wheels.
How much do brake repairs cost at Toyota?
What is the price of a brake job? Depending on the type of brake pad desired, brake pads for a Toyota might cost anywhere between $150 per axle and $450 per axle. For all four brake rotors to be replaced, the cost might range from $300 to $750. The labor and parts costs are included in this estimate.
Can I replace my own brake pads?
- Depending on your vehicle and driving style, brake pads should be replaced every 25,000 to 75,000 miles. You’ll discover that most professionals and automakers advise changing your brake pads every 50,000 miles on average.
- As part of your standard inspection, ask your mechanic to check your brake pads on a regular basis. Always remember to examine your brake pads to see if they appear worn if you prefer to perform your own vehicle inspections. When you notice severe wear on your brake pads, replace them right once to keep your car safe.
- Squealing, squeaking, and grinding noises are indications of wear. It’s probably time for a replacement if your automobile pulls to one side more than the other when you press the brake pedal or if you experience bouncing when coming to a stop.
- Your car’s performance, dependability, and safety can all be enhanced by replacing the brake pads. You can tackle replacing your own brake pads as a DIY project if you’re confident performing your own vehicle maintenance. As with any auto modification or repair, check your owner’s manual for any special instructions or instructions before you start.
Is it simple to change brake pads?
It could be time to change your brake pads if they are grinding or screeching. You’ll be pleasantly delighted to learn that you can quickly, simply, and without specialized tools replace the brake pads in your car’s disc brake system. You will also spend much less money if you do it yourself.
Can I just change my brake pads and leave the rotors alone?
You can definitely replace only the worn brake pads if they haven’t been damaged or thinned past the discard thickness.
It’s the rotor minimum thickness required by the rotor or car manufacturer.
The performance and long-term wear of the brake pads are influenced by the brake rotor and vice versa.
Typical wear patterns on old rotors include brake dust left behind from an old brake pad set.
The new brake pads may not therefore properly fit the old rotor. Due to this mismatch, the new brake pads may wear unevenly and generate noise and vibration (which will lead to premature brake pad replacement).
Additionally, keep in mind that an old, worn-out rotor can eventually require replacement. The time and money you think you are saving may not be as great as you imagined.
Resurfacing entails scraping a minute layer of material off the brake disc or rotor’s front and back surfaces.
By removing any grooves, pits, and remaining friction material from worn brake pads, this procedure makes a smooth surface for new brake pads to grab onto, allowing the new brake pads to wear down evenly.
If I replace the brake pads but not the rotors, what happens?
In order to stop the car, brakes use friction created when the brake pad presses up on the rotor. The vehicle’s ability to stop will be reduced if new brake pads are applied to a vehicle with damaged rotors because the new pads won’t make good contact with the rotor surface. When a pad is rubbed against a rotor with deep grooves, the material is harmed because the deep grooves serve as a shredder or hole-puncher. When changing the brake pads, make sure to also replace the rotors.
Do rear brakes degrade more quickly?
General, everyday use, mileage accumulated, the environment, and/or the owner’s driving habits are what lead to brake pads wearing out (s).
- For instance, a driver in a metropolis will use their brakes more than a driver in a rural area or on a route with low traffic.
- Another factor is speed. More frequent, light stops at low speeds will be less demanding on the brakes than frequent, heavy stops at high speeds. Your brake pads won’t be damaged by strong braking at high speeds as much as they are by light braking. Highway congestion is the primary cause of brake pad wear because of this. Additionally, the front brake pads will degrade more quickly than the back brake pads. As you brake, a lot more weight is transferred to the front of your car, which increases wear.
- Wear on brake pads is also caused over time by heat and friction.
- How much wear and tear your brake pads endure will also depend on which axle your brakes are on. The front brakes on your car will naturally wear out sooner than the rear brakes because they receive the majority of the braking force.
It’s critical to keep in mind that predicting brake wear is not an exact science. While some drivers’ brake pads may last up to 70,000 miles, others may need to have them replaced as soon as 25,000 miles have passed. You should take into account your driving style, the type of vehicle you drive, and how you use it.