assemble everything PRIOR to beginning! For this car, you’ll need 4.4 quarts of 5/30 weight oil, a set of metric wrenches (I believe for this car it’s a 14mm drain plug), a new oil filter (go to a parts store and tell them your car’s information), a filter wrench (once you know the size of the filter find the band wrench that fits (get both at the same time), jackstands to support the car (safety first! ), new oil, new Get a small container of DOT 4 brake fluid, washer fluid, transmission fluid, pre-mixed coolant, and possibly an air filter if you want to perform a full service oil change. Even if this stuff is pricey, you’ll need it all again after 3,000 miles if you change your own oil:)
Lift the automobile up. Find a metal frame component by looking under the front of the car. Be careful not to jack it up on anything brittle. There should be a jacking point in the front center of the vehicle. If you’re unsure, check your owner’s manual; it will provide jacking points. When it is high enough for you to get under it, slowly jack it up and position the jackstands on the car’s frame behind the front wheels. Slowly!!! shrink the jack. On the jackstands, the car ought to be supported. Take a peek now under the hood. Find the oil-related cap. Get rid of it.
Pull the drain plug out. Looking directly at a bolt on an automobile, clockwise tightening and counterclockwise releasing (lefty-loosey, righty-tighty). It will be towards the lowest position on the engine and will be on a sizable curved piece of metal (your oilpan). Remove the bolt completely. Put your drainpan underneath it to prevent a mess when the oil leaks.
Put the plug back in and tighten it once the oil has drained to a trickle. Keep it from being too low! Once it feels snug, cinch it up until it feels tight. Find the oil filter by moving the drainpan now. It need to be close to the driver’s side tire. It resembles a tiny pop can. To fully remove it, completely loosen it with the filter wrench. Catch the oil in the drainpan once more. Take a look at the old oil filter’s top! There ought to be a black rubber ring around it. If it doesn’t, check the engine to see if the ring is still there where the oil filter was removed. Important! Take your new filter, dip your finger in the NEW oil, and wipe some on the rubber ring once a little more oil has drained out of the oil filter hole. After that, apply the new filter. Avoid overtightening it! Once it seems snug, give it another half to full turn to tighten it.
Return to the car’s hood at this point and add the fresh oil. Use 4 full gallons for the Toyota and then little less than 0.5 quarts for 4.4 quarts. Reinstall the oil cap after that. Before starting the car, make sure to add the oil! Pressure test the vehicle next. Make that the oil cap, filter, and drain plug are all installed. Activate the automobile. Make sure there is no oil leaking from underneath by carefully inspecting. Ten or so seconds should pass. Alternately, utilize your dashboard. Either an oil pressure gauge or an oil light should be present. Look for any leaks once the gauge reaches about halfway up or the oil light turns off. If there are leaks, immediately turn off the engine and tighten the faulty component. If there are no leaks, raise the car with the jack until the jackstand can be removed, then SLOOOWLY drop it back to the ground. To make sure the car is up to par, check the oil dipstick now. You’ve completed the oil change.
Simply check all of your fluids inside the car’s hood after changing the oil if you want to perform a full service oil change. Everything should receive a perfect score. Fill it up with the appropriate fluid if it isn’t already full. Next, check your tire pressure and air filter. Please indicate how useful you found this article.
In This Article...
What does a Corolla oil filter cost?
After reductions, the price of an oil filter for a 2020 Toyota Corolla typically ranges from $8.99 to $19.99 based on a few configurable options. The cost of labor is typically more than the filter itself.
Recommended Oil Change Intervals for Toyota Vehicles
You were supposed to replace your oil every three months or 3,000 miles, whichever came first, according to an old proverb. This is no longer the case, though, as engine technology has developed and become more effective. Toyota advises consumers to have their vehicle’s oil changed professionally or by themselves every six months or five thousand kilometers, whichever comes first.
Recommended Oil Viscosity for Toyota Models
Toyota owners who enjoy DIY projects might be interested in changing their own car’s oil. We endorse this course of action because it offers customers a lot more cost-effective option than even bringing their car to one of the more reasonably priced service facilities nearby. Make sure you are using the right oil if you plan to change your Toyota’s oil on your own. Naturally, as Toyota Genuine Motor Oils are created exclusively for use with Toyota engines, we advise using these. But another choice that is suitable as well is synthetic oil with a viscosity of 5W-30!
Can I substitute 0W-20 oil for 5w20 oil?
The 20 in 0W motor oils (also known as 0W-20) stands for the viscosity measurement value, making them appropriate for usage in 5W applications. The most important factor to match when choosing a motor oil is that value. The pumpability at cold temperatures is shown by the 0W or 5W. Consequently, a 0W would flow more freely than a 5W and might be a suitable replacement. As a result, SAE 0W-20 can be used in place of SAE 5W-20 application.
**Provides improved fuel economy and faster flow while yet offering the same level of protection as 5W.
Will 5W-30 work in a Toyota Corolla?
* Recommended viscosity (SAE): SAE 0W-20, 5W-20, or 5W-30 engine oil is advised in severely cold temperatures since SAE 10W-30 or a higher viscosity engine oil may make it difficult to start the engine.
Here is an explanation of oil viscosity using 0W-20 as an example.
The characteristic of the oil that allows for cold starting is indicated by the 0W component of the oil viscosity rating. Engine starting in cold conditions is made easier by oils having a lower value before the W.
The number 20 in 0W-20 denotes the oil’s characteristic viscosity at high temperatures. If the vehicle is run at high speeds or with a heavy load, an oil with a higher viscosity (higher value) may be more appropriate.
Does my Toyota Corolla require synthetic oil?
There are two sorts of oil in the world, regular and synthetic, apart from different viscosities. Although there is a third variety that combines the first two, you often deal with either one or the other. The best option for your Toyota? What kind of oil is used in your Toyota? We offer all the solutions you require.
Does a Toyota need a specific kind of oil?
At this point, all current Toyota vehicles either require synthetic oil or at least recommend it. You must reference your manual to be certain. However, if you only decide to use synthetic oil, it will be far better for your engine and will simplify everything.
How can a Toyota oil filter be removed without a wrench?
Toyota oil filters can be taken out using one of nearly four different techniques. To complete your necessary task in a specific fashion, you are free to choose any of the approaches.
Using Sandpaper
The Toyota oil filter can be removed at a low cost by using sandpaper. You may easily create a tight grip over the oil filter by wrapping the sandpaper over it. After ensuring that your sandpaper is well wrapped, simply pull it in the other direction. The force generated produced by doing so will enable you to remove the Toyota oil filter without the use of a wrench.
Antique timing belt and key
This article also includes another helpful technique that involves the use of a key and an old timing belt. Use both of your tools to make a lever, place the belt over the oil filter, hold it in place with a key, and then unscrew it.
Screwdriver and hammer
To remove the oil, a screwdriver and sledge can also be useful. Basically, you need to place the screwdriver’s tip on the oil channel and use a sledge to pound the screwdriver’s base into the anti-clock bearing. The Toyota oil filter would be easily removed using the sledge’s energy.
Three legs adaptor
A three-legged adapter is another tool used for this design. This adapter is included in what is most likely the best tool for removing Toyota oil filters. For this reason, we may state that this tool is the least used, but in any case, it might provide you with a better result than a wrench.
As a result, if you’re wondering How to Remove Toyota Oil Filter without Wrench, all of these tools and techniques can be used.
There is yet another approach that can be advantageous for removing the oil filter without a wrench. But before attempting any of the other ways, this one should be tried.
The first method to try
Sometimes oil filters are loosely fastened, and you can even use your hand to access a Toyota oil filter. Give it a shot and attempt to open the oil filter counterclockwise. Maybe it’d be simple to open. You should use safety precautions and attempt it for this reason. To open the Toyota oil filter with your hands, keep in mind that gloves are recommended.
We should understand the importance of changing the oil filter after learning how to completely remove a Toyota oil filter without a wrench.
Importance of changing oil filter
The requirement to remove the oil filter in order to replace it is a fundamental phenomenon. In order to preserve the car’s reputation and keep the engine in good shape, it’s crucial to change the oil filter.
Facts to remember
Everyone should be aware of a few crucial details before attempting to remove the Toyota oil filter, both with and without a tool.
Verify that your car is chilly and that it was not in drive mode prior to two hours of work.
Before attempting to remove the filter, re-oil it since occasionally it won’t unscrew if there isn’t any oil on the filter.
You should also be aware of the proper technique for removing the oil filter with any instrument. It would be more tightened rather than becoming loose if you were to remove it in the wrong way.
Can you manually remove an oil filter?
With your filter, you’ll be getting up close and personal. Before beginning, put on your gloves and glasses to protect your hands and eyes.
Jack Your Car
If you are unable to reach the filter with the car at a level angle, jack it up. Keep in mind to use caution when doing this and to position the jack correctly underneath the automobile. Once the car is elevated, the jack should be replaced with jack stands.
Position Yourself Carefully
When you have a wrench, it is simpler to avoid lubrication that is dripping. You don’t receive that advantage using the method we’re looking at. Remember to keep your body and face away from the drip zone.
Place Drainage Pan
As usual, position your drainage pan to catch any dripping oil. If there is a spill, you could simply throw some rags under the pan on the floor to prevent damage.
Grab on
Take a firm hold of the end of the filter with your dominant hand. Try to rotate in a counterclockwise direction. Put all your strength behind it.
If it had previously been hand-screwed on by you or your mechanic, it could be possible to remove it without using any further tools.
How much oil is required to replace the oil in a Toyota Corolla?
Follow these instructions to replace the oil:
- Look for the drain oil plug by climbing underneath the Corolla. It is located beneath the engine.
- Slide the drain plug with the oil collection container underneath. The drain plug should be loosened using a socket wrench and a 14-mm socket.
- You can fully loosen and remove the plug to hasten the procedure by waiting until the oil begins to drain from the engine.
- Once the oil is finished, you must find the oil filter.
- Remove the oil filter using a socket wrench or other removal tool and an oil filter socket.
- Wait until all extra oil has finished draining before emptying the oil from the filter into the pan.
- Clean the area surrounding the oil filter fitting on the engine block using a rag.
- Then, take a clean rag and dab some fresh oil on it. Wipe the new oil filter’s edges clean with this oil.
- Reverse the removal instructions to install the new oil filter.
- Reinstall the drain plug and make sure not to overtighten it while doing so.
- The oil cap is located on top of the engine when the hood is opened. Add 3 to 4 liters of fresh oil. Take your time when adding fresh oil to prevent spills and/or overfilling.
- Check the dipstick after you’ve filled it to make sure you have the right amount of oil.
The maintenance light needs to be reset, last but not least. Turn the key to the accessory (ACC) position to accomplish that. Turn off the key after setting the odometer to mileage rather than trip. As you turn the key back to ACC, press and hold the button you used to switch to trip. While you press and hold the button, the light ought to blink.