For instructions on how to replace the headlight in your specific car and which headlight bulb to buy, consult your owner’s handbook.
In This Article...
Step 4. Unscrew the old headlight
Zullo warns that every car is unique. “He claims that while you can reach the bulb with some autos, you can’t with others. Sometimes you have to remove the inner fender to reach behind it because the battery or air filter housing is in the way.
However, changing the halogen bulb is all that is required if you can get the headlight open. This entails carefully unlocking the bulb after examining how it is secured. Zullo cautions that if the clips that are being used here are broken, the entire headlight would need to be replaced. “According to him, you must first examine how it is connected, softly disassemble it, and then carefully reassemble it without touching the bulb’s glass.
Step 5. Screw in the new headlight bulb
Without touching the bulb’s glass, carefully screw in the new bulb. If you do, the oil and grime on your hands could cause the bulb to burst once it heats up. Your car’s hood should be closed. Your headlights ought to work perfectly again after installing the new bulb, allowing you to enjoy driving your automobile day or night.
Most of the time, changing a headlight is simple and doesn’t need sending your car to the shop. See what other do-it-yourself auto maintenance tasks are available.
Do the daytime running lights on the 2018 RAV4 exist?
The EntuneTM Audio system is included with the 2018 Toyota RAV4. That implies that six speakers equipped with Bluetooth wireless technology will allow drivers and their passengers to listen to their favorite music. Your iPod can also be connected. Utilize the practical technology found within the 2018 Toyota RAV4 to listen to the music you want to.
Convenient Amenities
The 2018 Toyota RAV4 comes with a number of amenities that are designed to make driving more enjoyable. It has a sleek and distinctive exterior design. With this car and its instantly identifiable look, you can make an entrance. The eye-catching Halogen Daytime Running Lights (DRL) will undoubtedly draw attention. The front windshield’s acoustic noise-reducing UV reduction glass helps you block out sounds from the outside world and the inside of the car. You can feel safe when driving and enjoying it with friends and family by using these features.
What kind of car will a 9012 bulb fit?
Chrysler 200 and 300, Dodge Dart, Ram, and Fiat all have modern car headlight upgrades.
Winter is coming, so you might wish you had waited for a car or truck with HID headlights. But what should you do if your budget is tight and you’re not satisfied with the headlights?
There are many subpar replacement bulbs on the market that overpromise and deliver. The Chrysler 200 and 300, Dodge Dart, Ram, and Fiat 500, 500L, and 500X are among the vehicles with bi-halogen projectors and HIR2 (9012) bulbs that have a relatively affordable, high-quality solution, thanks to automotive lighting expert Daniel Stern.
Up until 2015 (2016 for Fiats), the Philips 9011 HIR bulb, which costs around $19, will work perfectly; the 2016s, which utilize 9005 bulbs, can use up to the GM bulb #23342527, which costs around $16. The 9011 adds 650 lumens, bringing the total to 2,350, although the fittings must be slightly trimmed.
Never touch the glass is the golden rule, whatsoever. Wear gloves or exercise extreme caution.
Look at this bulb box. Keep in mind that it has no packaging material and says nothing about the normal size. Yes, they place the bulb in a box with loose fittings and allow it to rattle. It was shipped to me in a box by the provider, with packing paper placed above but not below the bulbs.
To grab the bulb by the base, it is best to open the box from the bottom. The bulb is now part of an assembly, not something you have to force into a socket. That may be in part because it is directional; if you insert it upside down, strange consequences will occur. Later, more on that.
It’s time to get in the automobile. We believe the 200 and Fiat have access panels with comparable designs to those on our Dart’s wheel wells. If you pull the tab in toward the center of the automobile, they open with ease. Did we mention that you should turn the wheels in when parking the car? (Or out. It makes little difference, and you can probably manage with the wheels pointed forward.)
This allows you to view two connectors and a cap that you ought to disregard. If you give the cap a small turn, it should easily come off. (We did this at night; we apologize for the flash photography.)
With the cap removed, there isn’t much to see within. With your eyes, you can see even less, so I used my phone to take these pictures of the space between the tire and the light cavity. Here’s one more.
You must now gently and slowly insert your hand through the hole to enter it. You’ll feel the old bulb dying, not see it! Determine the direction of the wires by feeling it carefully; the new one must travel in the same direction.
You can sort of wiggle and jiggle it out by rotating it just a little bit (also remembering the angle it leaves at). I can do this; it’s so simple! The initial one will probably take some time. The second will finish in a few seconds.
The connected bulb is seen here. The wiring is held in place by a clip on the rear, which is fairly simple to remove using your finger (not too hard! ), a spudger, a credit card, or other tool. The best and least-forceful option is a spudger, a plastic prying tool commonly used for computers and other items.
The bulb assembly is simple to remove in any case, and since the replacement only installs in one direction, a mistake is prevented.
The replacement one is now installed. I installed the first one upside-down with the cables pointing down out of habit. When I turned on the lights and saw how it seemed, I realized that. After finishing the second side, I found the wires exit the bulb not downward but above. Weird? Absolutely! The cables appear to be under a little more strain as a result. I’m curious why they chose that strategy. In any case, I had to crouch down next to my other wheel and fiddle with the headlight tube while trying to remove the first bulb because it was stubbornly stuck in place. It took a lot of persistence, jiggling, and wriggling until it finally came loose, allowing me to insert it properly.
If your arm recalled where (and how) the old ones came out, replacing the bulbs was rather simple. After that, all that’s left to do is put the covers on, which is fairly simple.
I made a mistake with the camera angle, but the photographs may still be compared because they were all taken with the same shutter speed and aperture. The new ones have a wider range, are less brownish, are brighter within the cutoff, and emit more light on either side. They appear to spread the light more evenly. (The abrupt shutdown is done to prevent blinding incoming drivers; high beams are used for this.)
The high beams are brighter overall, have a less eerie pattern, and spread a lot more light to the sides. Both are improvements, albeit neither is a “HIDs versus halogens” comparison, and they each cost considerably less. If you don’t make silly mistakes, the project isn’t difficult.
Are headlight bulbs replaceable at Autozone?
To be clear, buying a headlight or tail light for a vehicle at AutoZone is pretty simple if you have the part number for it or simply know the make, model, year, and occasionally even the trim of the car. When you visit a dealership or repair facility, labor is frequently added to the cost of the headlamp.
If your headlamp is easily accessible to the installer and is in most cases, Autozone will replace it.
Is it challenging to switch headlights?
Even if you have the most expensive wheels, if your headlights aren’t working, it won’t mean much (and as we know from numerous movies and cop shows, a burned-out light will lead to an unwelcome stop by a highway patrol car). Thankfully, changing a headlight bulb is a rather simple procedure.
Tools required:
- brand-new light bulb(s) Make sure you purchase the appropriate bulb type for your car (your local auto parts store should be able to match a bulb with your make and model)
- alcohol-based tissues and wipes (to clean and hold the new bulb)
- tool for Phillips screws
Instead of from the front of the automobile, you’ll access your headlight bulb via the engine compartment. Locate the headlight close to the front of the car by opening the hood. It will be housed in a bulb holder and connected to the bulb by a power connector, which typically has three wires.
Depending on your vehicle, the power cables are connected to a plug at the base of the headlamp and secured by a plastic catch, a metal clip, or a screw cap. Push down on the little lever at the top of the plastic catch as you take the plug out. Hold onto the metal clip as you draw it up and away if you’re dealing with one. When working with a screw cap, turn it counter-clockwise to unscrew it.
Holding onto the base of the old bulb, you should be able to remove the back of the headlight holder after the wires have been severed. In some circumstances, you might need to slightly spin the bulb to release it.
Use tissues or gloves to handle the replacement bulb; you don’t want your skin’s oils to get on it. Before you install it, you should give it a thorough cleaning with an alcohol wipe. When the bulb is prepared, insert it into the plug’s base. No rubber gasket will be seen if it has been placed properly. The headlight holder and power wires can be plugged back in when the bulb has been installed. Make sure to switch on your headlights to test the bulb.
Working with your headlights differs slightly from changing your rear tail lights, which include your brake lights. On some models, you may unscrew the housing that houses the bulb from the outside, while on other models, you have to do so from inside the trunk. To access the bulb after unscrewing the housing, you might need to work with tabs, screws, or tiny knobs on the tail light cover (make sure not to lose the screws if you need to remove them). The electrical wiring won’t need to be taken out, but be careful not to pull the housing out too much lest you rip the wires.
The bulb should be easy to remove by either pulling it out straight (as in most contemporary cars) or by pushing it in while simultaneously unscrewing. Replace the housing and reattach it when the replacement bulb has been installed (screws, tabs, knobs, etc.). Once more, be careful to test the bulb by turning the ignition on and using the brakes.
Do I have to unplug the battery before changing the headlight bulb?
When replacing a blown headlight bulb, always unplug the battery. The electrical system of your car is connected to the headlight bulbs. While the alternator recharges the battery, they will draw power from it. You should always disconnect the battery when working on your car’s electrical system to be safe. The battery doesn’t have to be taken out. Instead, all you have to do is unplug the ground cable (the black cable) until the blown headlight bulb has been replaced.