I am aware that this thread is older… I’ve done a lot of research on this and have discovered 3 viable choices. The hub bore of the Tacoma is larger even though the wheel stud spacing (6 X 5.5) is the same (106mm vs 100mm on the Xterra). Make sure the wheel is properly centered. Steel wheels may be mounted easily using your stock Nissan hubs. Steel wheels can’t use hub rings since there isn’t a counter bore for the rings to fit into, thus you must center them properly using the lug nuts (not the best option, but doable).
New lug studs must be purchased and replaced. On its aluminum wheels, Toyota uses lug shanks, also known as mag shanks. The wheels could come off if you use the standard acorn seat lug nuts (Nissan style). In fact, I’ve witnessed someone attempt this and lose a wheel while driving. Here is a picture…
If you’re set on using aluminum wheels, you can follow my lead. Go to O’Reilly Auto Parts and ask a knowledgeable employee to hunt up some lug nuts in their catalog for you (they cost about $3 apiece). You can replace ALL OF YOUR WHEEL STUDS with some that meet the following requirements:
In This Article...
What kind of bolt design is a Tacoma?
The wheel bolt pattern for vehicles with two-wheel drive and models from 2000 to 2020 is five lugs, 4.5 inches (114.3 mm) high, positive offset. A 4WD vehicle has a medium offset of 6 lugs, 5.5 inches, or 139.7 mm.
Although having this knowledge is crucial, it might not be sufficient to enable you to make the necessary adjustments when you wish to change the vehicle’s tires. Because of this, we are going to give you some additional information here. For even more accurate information, be sure to take the time to search for the model year or trim model on Vehicle History.
For a Nissan Frontier, what wheels will fit?
16×8 wheels 265/70 and 285/75 tires, which may rub or require trimming. 17×8 wheels with 5 265/70 tires. 18×9 wheels 285/60 and 265/60 tires. Popular wheel sizes for a Nissan Frontier of the second generation with a leveling kit:
16×8.\s\s 17×8.\s\s 18×9.
Does a Nissan Xterra fit Toyota wheels?
The Toyota wheels are snug. Though hubcentric spacers are available, they are not necessary. Get a good set of lug nuts, torque your wheels according to the recommended order, and you should be good to go. My vehicle was a 2002 4 runner. Are you a Hawaii native? based on the Ahis on your profile picture, I’m assuming you’re?
You might not get a response because this is an old thread, and you might be restarting an old thread. Consider starting a new thread, please.
Q: What rims are interchangeable between different cars?
Fortunately, any car has a replaceable rim available. All you need to do is make sure the new wheel’s bolt patterns, size, and offset match those on the old one.
By looking at the sticker label on the inside of the driver’s door or measuring the rim, you may determine the new wheel’s proper size. Take your car to a mechanic if you are not the do-it-yourself kind.
Q: What cars use a 5114 3 bolt pattern?
A wheel hub with 114, 3 and 5 bolts or nuts is all that a 5114 3 bolt pattern is. 5114,3 bolt designs are used by various car manufacturers and models.
What vehicles have a bolt pattern of 6×5 5?
There are many various kinds of vehicles out there, and each one has a unique bolt pattern. We’ll give a thorough explanation if you’re seeking for a new set of wheels but are unsure of which vehicles have the 65-5 bolt pattern.
The Ford F-150, Chevy Silverado 1500, GMC Sierra 1500, and Dodge Ram 1500 are common trucks having a 65-5 bolt pattern.
The Toyota, Nissan, Isuzu, Mitsubishi, Mazda, Infiniti, Lexus, Dodge, Honda, Jeep, Cadillac, Acura, Chevrolet Silverado, Ram, GMC Sierra Denali, and other cars also utilize this bolt pattern.
Fitting of Nissan Frontier with 265 75R16?
Oversized tires on a Nissan Frontier are a surefire head-turner. They need to have come with with bigger tires because the aesthetics are so good. Going with wider tires actually suits the Frontier better because it is quite a square-shaped, brutish Ute/pickup. Taller wheels help enhance break-over angles when driving off-road and provide greater obstacle clearance thanks to increased ground clearance.
What size tire can you comfortably place on a factory Nissan Frontier without making any other modifications? With a factory suspension, a Nissan Frontier can accommodate tires up to 265/75/16 in size. This tire size does not require trimming of the fender liners or create any rubbing.
Even with that 2.5 spacer, the largest size you can fit is the previously mentioned 265/75/16. Additionally, without any additional modifications, it is the biggest tire that can be mounted on the factory wheels. That size is exactly 31.6 inches, which is barely under 32. You run the risk of the wheels scratching and striking the fenders at full lock and full compression if you install an aftermarket rim with a higher negative offset.
Before adding larger tires to a stock truck or ute, the following five considerations must be made:
- Clearance for fender liners
- Backspacing
- Rim offset
- Spare-wheel room
- Articulation (Flex) (Flex)
You can get away with a 265/75/16 or a 265/70/17 when mounting a larger tire to the standard Nissan Frontier rims. Yes, it is a thinner tire than, example, a 285 width, but the 65 and 70 profile, which is taller but the same width as the original tire, offers more ground clearance.
Let’s examine the requirements in more detail as well as the consequences of a larger tire upgrade.
Does 6×5 5 equal 6×139 7?
Premium Subscriber They all follow the same bolt pattern. Although one is listed in metric and the other in standard, they are identical. Therefore, they do fit.
What does the wheel metric 6×139 7 mean?
The stud count (six) and bolt circle measurement (139.7), the notional circle determined by the studs’ centers, make up the 6×139.7 Bolt Pattern or Pitch Circle Diameter (PCD).
Vehicles from Acura, BAIC, BAW, Cadillac, Chery, Chevrolet, and Daewoo all use the 6×139.7 bolt pattern. The following is a complete list of car makes and models:
On a wheel, what does 6 139.7 stand for?
Automotive Bolt Pattern
The PCD, or more popularly, the “Bolt Circle,” is another name for the bolt pattern of a wheel or vehicle. It stands for “Pitch Circle Diameter.” The centerline measurement of the wheel studs on the mounting hub of your vehicle and the number of wheel studs are the two elements of a bolt pattern on a vehicle. The quantity and location of the bolt holes on a wheel that align with the studs when it is fitted into the hub are determined by your PCD. You will be able to decide which wheels will and won’t fit your vehicle based on the diameter of the bolt pattern.
Calculating Your Measurement
On most modern automobiles, the standard bolt pattern runs from 4 to 8 lugs. A bolt circle of 6139.7 would represent a 6-lug arrangement in a circular with a 139.7mm diameter. There are various methods for determining a bolt pattern. A measuring tape is usually a practical option, but for the most exact measurement, we suggest utilizing a bolt pattern measuring tool. Measure from the center of one wheel stud to the center of the opposing wheel stud if your car has an even number of studs. When measuring a 5-lug vehicle, take your measurement from the center of the closest stud to the outside of the furthest stud.
Inches or millimeters?
For some people, figuring out the bolt pattern on their car can be challenging. One frequently asked query is “If my car has a 54.5 bolt pattern, will these 5114.3 fit? or “Why does this wheel’s description mention 5139.7 while my car needs 55? The simple answer is yes, and there is a brief explanation of the millimeters vs. inches unit discrepancies utilized in the text. Although some may offer the measurement in inches, the most typical phrase for a bolt pattern is the metric unit. The United States used to provide measures in inches for vintage cars, and some contemporary cars and trucks still do so today. You can easily find conversion tables and other information online or by contacting your local retailer.
Fitment Assurance: The initial step in your quest to equip your car with some new wheels may be to understand your vehicle’s bolt pattern. We’d like to remind you that in addition to your bolt pattern, there are a number of other elements that affect wheel fitment and sizing. To ensure that a wheel is properly fitted to your car, it’s crucial to be aware of the tire size, wheel size, offset, and backspacing. To gain precise information regarding the fitment for the wheels you’re buying and installing on your car, check with a fitment professional, do some online research, or call a nearby shop.
For updates and the most recent information from the Factory Team, follow us on social media!