Hello, and thank you for your letter. The “lenses” or plastic coverings for the taillights are not offered for sale individually. If you wish to do that repair, you will have to buy the full taillight assembly. Now, keep in mind that you might be able to locate one used for a lot less money. In light of this, you should make sure any used parts are either inspected or are of “known good” quality. Junk yards, pull-and-pay shops (where you find and take the part on your own), and even online are common venues to find used units. Make an appointment at your home or place of business with our service department if you require help changing the taillight.
In This Article...
How much time does a tail light assembly replacement take?
Get Ready Fortunately, changing the tail light bulbs isn’t hard and shouldn’t take you more than 45 minutes to an hour. Be careful that newer models could be a little trickier to disassemble than older ones because there will be more wires.
How much does a new tail light assembly cost?
Cost of replacing a tail light Expect to pay between $200 and $500 if you elect to have a professional replace your tail light assembly. If you own a high-end luxury or performance vehicle, the cost of the job may increase.
Tail Light Assembly
The group of lights positioned on the back of your car is known as the tail light assembly. They are made up of the reverse lights, brake lights, and tail lights. Each set of lights has a specific function for nighttime conspicuity. The red tail lights are connected to switch on in conjunction with the activation of the front position lighting. When the driver applies the brakes, the brake lights turn on. On both sides of the car, these lights, which are a vivid red, are mounted in multiples of two.
In some vehicles, the brake lights and the tail lights can be merged. They can be placed as a dual-intensity bulb in these circumstances, with the brake-light having a brighter intensity. Fog lights are also used in cars to improve rear sight in heavily foggy conditions. When the driver shifts into reverse to back up the automobile, the reversing lamps turn on. For both your safety and the protection of other drivers, you must make sure the tail lights are in functioning order.
You should replace the tail light assembly if your tail lights have sustained external damage or if the lenses are dim. For every make and model of vehicle, Buy Auto Parts keeps a large selection of tail light assemblies in stock.
We offer excellent aftermarket components as well as original OEM replacements. All of our auto components are rigorously examined and backed by a warranty. Choose the correct year, make, and model of your car from our online catalog to view the components that fit it. You can purchase premium tail light assemblies at Buy Auto Parts for unbeatable pricing, plus free shipping. Contact us by email at [email protected] or over the phone at 1-888-907-7225 if you have any inquiries about our auto parts.
Can I replace my own tail light?
Anyone can learn how to replace a broken brake light. A replacement bulb costs approximately $10, and doing it yourself will save you about $20 in labor costs as well as the time it would take to drive to the shop and wait for the work to be completed.
How can I fix a broken tail light cover?
Craft glue might work if your tail light cover simply has a crack in it. However, if the damage is more significant, you should use some lens repair tape to cover the exposed region. This is available at most auto parts retailers, including this dealership.
Can you operate a vehicle with a cracked taillight cover?
It’s against the law to drive while your tail light is out. Every car must have two taillights that are functional. All tail light lenses must also be transparent. Additionally, they must be in good shape and be the original automobile manufacturer’s lenses.
Installing dark bulbs or lenses that render tail lights ineffective is another unlawful practice. Only tail lights with U.S. Department of Transportation certified bulbs should be installed on your vehicle.
How is a tail light assembly taken out?
Safety Advice
Always use safety eyewear when performing maintenance on your car. When necessary, put on additional personal protective equipment (PPE), such as latex gloves or closed-toe shoes.
On the back of your car, find the tail light assembly. When you use your brakes or turn signal, they illuminate on each corner.
Remove any mounting screws that are present on the exterior of the tail light assembly, if necessary.
O’Reilly modifies the tail lights?
While you wait, at no cost to you, our parts specialists can swiftly and easily change wiper blades because they are experts at changing headlamp and taillight bulbs.
Step One
Find out first how to get to the taillight bulb on your car. While you can access the taillight housing from the outside of some vehicles, you have to open the trunk on other cars and SUVs to get to the taillight bulb.
Consult your owner’s manual if you need help figuring out how to get to the taillight bulb.
Step Two
You can decide what equipment you’ll need now that you know how to get to the taillight bulb. Either a flathead or Phillips screwdriver will probably be required. To remove the screws keeping the taillight housing in place, gather the necessary equipment. You might not require tools if the taillight housing is accessible on your car. The cloth covering may easily be removed to reveal the bulb in its socket.
Step Three
Once the housing has been removed, decide which bulb or bulbs need to be replaced. Find the light bulb holder that contains the one you need to replace. Unscrew it by rotating it about a quarter turn and pulling it out to dislodge it.
Step Four
Pulling the bulb out of the socket slowly will allow you to remove it. The majority of them simply pull out, but others might need to be turned a quarter turn. There might be some additional screws to remove depending on how your car is set up. To avoid shattering the bulb, be gentle when doing this.
Step Five
Make sure the socket is clear of any dirt and debris before replacing the bulb. In the same way that you removed it, put the bulb back into the open socket. In order to prevent damage to the bulb, you might want to use gloves.
The procedure you used to remove the old bulb should be repeated. Reinstall the taillight housing by putting in any missing screws. If you had to remove any extra components to get to the taillight bulb, replace them.
Step Six
Find out more about high-quality lighting items, where to buy your car part, or how to locate it.
Only for entertainment and informational reasons, the information in this article should not be used as a substitute for consulting a qualified technician or mechanic for expert guidance. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.
Are brake lights replaced by AutoZone?
AutoZone will they replace brake lights? Although AutoZone doesn’t really provide brake light replacement services, our staff can answer any inquiries you may have, direct you to the necessary supplies to get started, and even lend a hand if necessary.
Are the brake light and the tail light interchangeable?
The primary distinction between brake lights and tail lights is that the latter only come on when the brake pedal is depressed, whereas the former illuminates as soon as the headlights are turned on. While both lights are red, brake lights often produce a red light that is more vivid.
What is a housing for a tail light?
The component of a vehicle’s tail light assembly that houses the bulb, wiring, and lens is called a tail light housing. To guarantee that your tail light is functioning properly, it locks and protects these vital lighting components.
Why does my tail light not function yet my brake light does?
A broken light bulb is the most frequent cause of brake lights that don’t work yet taillights that do. A busted fuse, a defective brake light switch, or problems with the wiring can also be to blame.
While the brake lights on your car should illuminate when you use the brakes, they don’t. Given that both lights’ connections effectively come from the same source, this is a peculiar issue. When you apply the brakes, either one light flashes more than the other or the taillights entirely turn off.
There is a cause for every problem, and every problem has a remedy. Why your brake light doesn’t function yet your taillights do is explained in more detail below:
Can you cover a broken tail light with red tape?
You are aware of how expensive it can be to fix a broken tail light if you have ever received a citation for it. What if, though, there was a temporary remedy you could use until you could get a replacement?
In fact, there is! To hold the broken piece in place until you can get a replacement, you can use red tape or even electrical tape.
The first step is to use some alcohol or glass cleaner to clean the area around the break. This will improve the tape’s adhesion. After that, cover the break with a piece of red tape. To make sure it’s secure, you might need to apply a couple pieces of tape.
You should apply electrical tape with the adhesive side facing the break. Then, to make sure it’s secure, wrap it around the region a few times. Although clear packaging tape works just as well, it is not as durable as electrical tape.