- Make sure the car is parked on a level surface.
- Turn off the automobile and apply the parking brakes (or emergency brake).
- Ideally, you should be able to lock the wheel that is diametrically opposed to the one you want to lift. You can perform this with a block, stone, or anything else you have on hand.
- Find the jacking locations below the car. They are situated just in front of the back tire and after the front.
- Correctly insert the jack into the jack point. The jacking point should be at the center of it.
- Take the following safety measures. When a tire jack is used incorrectly, the car could quickly drop off the jack and cause significant damage or even death. If you don’t have a jack stand handy, a smart solution is to utilize the spare tire under the car. Avoid placing any part of your body underneath the car while the jack is holding it up.
- Raise the car slowly. Make sure the jack stand is still in the right place and not moving when raising. Avoid raising the automobile higher than is required to install a jack stand or to freely remove a tire. If utilizing a jack stand, place it underneath the vehicle and slowly lower it until the vehicle is resting on the stand.
In This Article...
Warning, Do not do this when using the tire jack
- Never place something on or under the jack when elevating the car.
- Don’t raise the car any higher than is necessary to change the tire.
- Make sure nobody is anywhere near the car before lowering it. Before descending, sound a warning to any surrounding persons.
- If someone is inside the car, don’t raise it.
- If getting beneath the car is necessary, use a jack stand.
Where should the jack stands go?
The lifting point must be immediately beneath the jack stands. Every jack point ought to have ample space for the stand’s grasp. A correctly rated jack stand will support the weight of the automobile as long as the stand is flat when the hydraulic pressure from the floor jack is released. If the jack is inclined or the weight of the car doesn’t come down flush on top of the stand, issues arise. Once you are certain that the car is firmly placed against the stand, only fully lower the hydraulic jack. The stand shouldn’t move at all.
Can a car be left on jack stands?
After employing a hydraulic lift or jack lift, a heavy object can be supported by a jack stand. In order to replace a wheel, change the oil, or inspect any other component underneath a car while working on it, you would use a jack stand. We have enquired as to the maximum amount of time a car can be supported by jack stands. Here is what they gave us.
A car can be left on jack stands for however long is necessary. For days, weeks, months, or even years, your car could be left on jack stands. As long as your car is jacked on a flat surface, everything will be OK. One thing to keep in mind is that it’s preferable to put your car on concrete rather than asphalt because asphalt is softer and your jack stands risk leaving a mark if left there for an extended period of time.
Since your tires will gradually lose air if you leave your car standing on its own and you run the risk of damaging your rim, leaving it on jack stands is a smart way to store your automobile. Additionally, check the vehicle’s security to ensure that even a small bump won’t cause it to overturn. Continue reading for more details about jack stands.
We hope the links provided are helpful to you before you continue reading. We may receive a commission if you buy something after clicking on one of the links on this page, so thank you!
Are car jack stands secure?
Jack stands should be rated in pairs if they were made after 2015. In other words, a pair of three-ton jack stands should be able to sustain 6000 pounds without failing. The American Society of Mechanical Engineers (ASME) and the American National Standards Institute (ANSI) provided the ratings (ASME). The standards may also be referred to as ANSI PASE and ASME PALD (Portable Automotive Lifting Devices) (Portable Automotive Service Equipment). When tested for 10 minutes at 200 percent of their specified load, stands made to this requirements distort less than 1/8 inch. But keep in mind that testing is done by the manufacturer, not by ANSI or SAME, and it only serves to support the manufacturer’s claim that the product line is certified. Each set of stands is not tested on an assembly line.
The minimum load rating required for a pair of jack stands to support the front or rear of the car is, in theory, the weight of your car divided by two, which can be found in the owner’s manual or online. However, 1) you generally don’t want to utilize the minimal for your safety and peace of mind, and 2) weight is only one aspect. The car can shake more if the jack stands are extended higher than necessary to reach the underside of the vehicle and support the load steadily. For instance, a 6000-pound vehicle weighs 3000 pounds, so even a small pair of two-ton (4000-pound) jack stands would be heavier than that on paper. However, two-ton jack stands are often short and may not extend all the way to the truck’s frame rails.
Use the compact two-ton jack stands for small passenger cars, the three-ton stands for medium- to large automobiles or mid-sized SUVs, and the genuine five- or six-ton truck jack stands for full-sized trucks or SUVs.
I need how many jack stands.
You seem to be working on some interesting projects! The type of work you’ll be conducting will determine how many jack stands you’ll need.
Generally speaking, you’ll need two jack stands if you’re only elevating one end of your car. You’ll need four if you’re lifting the entire vehicle.
Make sure you are familiar with the best safety procedures and the ideal lift points for your specific vehicle before putting it on jack stands. Your car’s owner’s manual will tell you where to put the jacks.
Do you wish your auto insurance coverage carried out a bit more work? Jerry makes the procedure quick and simple if you’re prepared to look for better insurance options.
After you download Jerry, all you need to do is respond to a few questions that will take you around 45 seconds to do, and you’ll get car insurance rates for coverage that is identical to your current plan right away.
Can I jack up my automobile using four stands?
You’ll need two jack stands if you’re lifting just one end of your car. Use four jack stands if you’re lifting the car in its whole. They can stay upright on soft ground like asphalt or grass if the plywood is thick.
I need to change my oil, how many jack stands do I need?
There are two secure methods for lifting your car so you may change the oil. You can either drive your car onto a set of ramps or utilize two jacks positioned on either side of the front of your vehicle.
Why do jack stands deteriorate?
Working underneath a car is inherently risky. Take the following safety precautions whenever you are changing the oil or performing other maintenance that need you to operate underneath an automobile to avoid dangerous accidents and serious injuries:
- After raising the car, check to see that the jack stands are securely fastened and remain vertical. They should also make good contact with the lift points. Before climbing underneath your automobile, make sure it is stable. If something doesn’t seem right, you might jack the car up once again.
- Find the Lift Points and Jack Stand Points: To find out the optimum way to lift your car, consult the owner’s manual. Prior to jacking, confirm that your jack and jack stands are compatible with the vehicle’s lift points. In the event that any of the lift points seem damaged, don’t try to jack up your car. Consult your dealer or a reliable mechanic instead.
- Examine the Jack Stands and Car Jack for Condition: Use high-quality tools from a respected manufacturer, and carefully inspect your jack and jack stands before using them.
- Verify the Weight Rating: Verify the weight rating of the product manuals and labels to make sure the car jack and jack stands are suitable for your vehicle.
- The Best Surface for Jacking a Vehicle is a Flat, Hard Surface: A concrete garage floor or any flat, hard surface works best. Jack stands may move on soft surfaces.
- Chocks, which resemble wedges, should be used before lifting to stop a vehicle from rolling. At the end that isn’t being lifted, two should be positioned behind the wheels. You can also use a brick or a substantial piece of wood in place of chocks.
When do jack stands break down?
You might be concerned about how safe it is to get underneath your vehicle after you’ve raised it on jack stands.
The National Highway Traffic Safety Administration (NHTSA) conducted research on cases involving injuries linked to “jack failures,” and discovered that in one year, an estimated 4,822 people nationwide were treated in hospital emergency rooms for injuries brought on by the failure of a jack while participating in a motor vehicle-related activity.
In the majority of these cases, the car or jack slipped and fell, or the jack itself failed or lost pressure, causing the vehicle to plummet. A little more than three-quarters of those harmed were struck by the car as it dropped off the jack.
Be cautious of jack-stands that have been recalled due to potential failure hazards and make sure you observe all safety precautions while using them to lower your risk of suffering these types of injuries.
Do jack stands for 2 tons suffice?
Each type of automobile jack is rated to support a particular weight range, and the precise rating is listed on the jack itself in the form of a clearly visible sticker. It’s crucial to realize that you won’t be lifting your car or truck in its whole with a single jack, so you don’t need one that is rated for the vehicle’s total weight. A two-ton jack should be adequate for elevating a corner on the majority of sedans and small automobiles. In order to provide you with the necessary margin of safety, a pickup truck or SUV may need to be rated at double that weight (four tons).