Make sure that all four tires have the proper tire pressure before attempting to reset the TPMS system on your 2013 Hyundai Elantra. Usually, this will result in the light going out, and all of Your problems will be behind you. But occasionally the light remains on because the pressures don’t read correctly. This isn’t much of a problem, and it can be resolved with ease. You must operate your vehicle for at least 10 minutes at 50 mph or more. On the majority of roadways, this is safe to do; however, I wouldn’t advise it in a school zone. The light ought to be off the next time you start your automobile. You can also turn your key to the ON position. The TPMS reset button should then be pressed and held down until the light blinks three times. The vehicle should be started and left to idle for at least 20 minutes.
Make sure the tire pressure is right before starting the 2013 Hyundai Elantra to reset the TPMs. After 10 minutes, press the reset button, which is located to the right of the steering wheel. You might need to keep pressing the button until the light flashes in some circumstances.
The location of the TPMS is a mystery to me. I’m going crazy over it. My CRV makes it quite clear.
In This Article...
How Do You Reset A Hyundai Elantra’s TPMS?
You may reset the tire-pressure monitoring system in your Hyundai Elantra once you’ve found the TPMS.
The following steps will show you how to reset the TPMS on a Hyundai Elantra:
1. Turn the ignition to the “ON” position and insert the key.
2. Avoid starting the car.
3. Hold down the TPMS reset button while waiting for the tire pressure light to blink three times.
4. Let go of the TPMS button.
5. Start the vehicle.
6. Permit the sensor to reset for 20 minutes.
Your tire-pressure monitoring system will be reset by following these instructions. After putting air in your tires, it’s crucial to reset your TPMS since it keeps your knowledge of your tire pressure accurate. When your tires need to be inflated, the tire pressure monitoring system will let you know by turning on the tire pressure light.
On a 2011 Hyundai Elantra, how do you reset the tire pressure indicator?
The reset button should be visible if you look to the right lower side of your steering wheel. Once the button has been pressed, wait for 10 minutes. It should flash before being reset. Make sure the tire pressure is right before starting the 2011 Hyundai Elantra to reset the TPMs.
TPMS Tool and OBDII Module Procedure
1. Fill up each tire to the recommended level as shown on the vehicle placard.
2. In your TPMS Tool, choose a vehicle make, model, and model year that has OBDII support.
3. From your TPMS Tool’s menu, choose OBDII.
4. Beginning with the LF tire, scan each sensor using your TPMS tool in the following order: LF, RF, RR, and LR.
5. After all sensor IDs have been saved, drag the mouse underneath the letters OBD using the TPMS Tool or V button. then click the enter key.
6. With the engine off, turn the ignition to the ON position.
7. Connect the TPMS Tool and OBDII connector to the vehicle’s OBDII port. Ensure that the OBII Module’s green light is on and that your connection is safe.
8. Upload the sensor IDs by choosing Upload Car IDs from the TPMS Tool menu.
9. The IDs have been successfully uploaded when RELEARN COMPLETE / IDs UPLOADED TO CAR is shown.
10. Insert the key in the OFF position. Check each sensor again.
11. For at least 10 minutes, drive the car at a speed above 30 mph while keeping an eye on the low tire pressure monitor to make sure it isn’t blinking.
Note: Lo-line and hi-line TPMS are both used in these vehicles. Hi-line systems display to the driver the air pressure and individual tire locations for each tire. Lo-line systems merely indicate when one of the four tires is under-inflated and do not display specific tire positions. Be careful of the type of TPMS you are servicing because some models change systems in the middle of the year.
On a 2013 Hyundai Sonata, how do you reset the tire pressure indicator?
Turn the key to “on” when the car is off, but don’t let the engine run. When the tire pressure light blinks three times, release pressure on the TPMS reset button. To allow the sensors to reset, start the automobile and let it run for 20 minutes.
On a Hyundai Elantra, where is the TPMS reset button located?
Under the steering wheel is typically where you’ll find the TPMS reset button. You can refer to your owner’s manual if you can’t find it.
The Hyundai TPMS reset button is where?
Usually found somewhere under the steering wheel, the reset button for the tire pressure monitoring system. When the tire pressure monitor system light blinks three times, hold down the reset button.
What is the Hyundai Elantra’s TPMS?
Hyundai vehicles are equipped with TPMS, or tire pressure monitoring systems, which may detect low tire pressure in any of the car’s four tires and issue an alert. According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle.
According to the table below, a TPMS from one of two manufacturers is installed as a component of the valve assembly in every Hyundai vehicle. The tire pressure monitor ECU/receiver receives the data from the sensor, which detects the pressure and temperature inside the tire, together with the TPMS’s distinctive ID.
If the TPMS ID is stored with the ECU, the placard pressure is checked with it, and if there is a pressure difference, a warning light is illuminated on the dash-mounted display.
Does programming of Hyundai TPMS sensors are required?
Before being inserted in the tire, these sensors need to be programmed with the appropriate protocol/application information for the vehicle, and they then need to be retrained to the vehicle.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
Will the tire pressure light automatically turn off?
Tire pressure can be impacted by overnight temperature variations or by cold winter days. The low-pressure indicator may then display as a result of this. The pressure in your tires can change by up to 10 PSI when there are significant temperature changes between day and night.
After about 20 minutes of driving, the light may turn off on its own when the right inflation level stabilizes and the air in your tires warms and expands.
In any case, you ought to have your air checked immediately. Your tires are at least 25% underinflated, according to the TPMS light. This poses a risk to your safety, especially if the load is close to your vehicle’s maximum load capacity. There is a higher possibility of tire failure, degraded handling, and increased tire wear and tear. Your fuel economy may also suffer.
What distinguishes TPMS from low tire pressure?
A tire pressure monitoring system (TPMS) is built into your car and is intended to monitor the air pressure in each tire. The Low Tire Pressure indicator on your dash goes on automatically when the system detects a low tire. Until the tires are checked and the pressure is adjusted, this light will remain on.
On the other hand, the TPMS light is intended to turn on when there is an issue with the monitoring system itself. For instance, if a sensor in a wheel malfunctions, the TPMS light will illuminate and remain on until the issue has been resolved.
The maintenance process is not replaced by the TPMS system. Even if the indicator is not on, you should physically check your tire pressure at least once every month.
The informative nature of the aforementioned claims warrants independent verification. kindly visit our
Why are my tires fine but my TPMS light is on?
It’s likely that one or more of your tires have low air pressure if you see the tire pressure indicator turn on. However, even if your tires are in good condition, there are a number of things that could cause the sensors to go off, so you shouldn’t rely only on the data from the tire pressure monitoring system of your car.
AutoZone is able to check TPMS sensors.
You can determine if your tire pressure monitoring system is corroding or failing within your wheel with routine inspection; if so, you will need to replace it. For your repair, AutoZone carries every tire pressure monitoring system item you’ll need, enabling you to drive again efficiently and safely.
My low tire light won’t turn off; why?
If your tires are properly inflated yet the warning light continues to illuminate, you may have a leak or a TPMS issue in one or more of your tires. To determine if a tire has a leak is not difficult. Simply double-check the air pressure in each of your tires with your tire gauge. If all of the tires have the proper air pressure, one or more tire pressure sensors are likely to be at fault, necessitating repair work on your tire pressure monitoring system. You’ll need to replace or repair the tire if you notice that one or more of your tires’ air pressures have fallen.
What occurs if TPMS sensors are not replaced?
Customers who ask you to turn off their TPMS light just and leave the underlying problem unattended can put you and your business at unnecessary risk. Without addressing the problem, you are breaking the NHTSA’s “make inoperative” clause, which makes shops legally obligated to disable the TPMS. It is your duty to let the customer know this and to decline service if they don’t want the problem handled properly.
It is strongly advised to replace all sensors at once if a single sensor has reached the end of its useful life. When one sensor fails, the others are likely to follow suit quickly, just like with headlights. The same holds true for replacing an impact sensor or damaged valve stem. Your consumers should be aware of this since it will assist you give their vehicle the finest care possible. They also find it convenient.
The TPMS sensors must always be reactivated and calibrated for drivers who change their tires as the seasons change. If you don’t do this, the car’s TPMS won’t function properly and could turn on the TPMS light.
How does the TPMS identify each tire?
The anti-lock brake system’s wheel speed sensors are often used by an indirect TPMS. On-board computer systems can employ these sensors to compare wheel revolution rates between individual wheels as well as to other vehicle operation data, such as speed.
The computer can determine the relative size of the tires on your car based on how quickly each wheel rotates. The computer determines that a tire is underinflated when a wheel starts spinning more quickly than normal and warns the driver accordingly.
So a system that monitors tire pressure indirectly does not genuinely detect tire pressure. The same kind of measurement you may observe with a tire gauge is not being processed electronically. An indirect tire pressure monitor only counts the rotational speed of your tires and sends instructions to the computer to activate the indication light when something seems off with the rotation.