When you experience the same problem, you should start by following this technique, which is identical to resetting the airbag light on a Toyota Camry. It needs timing the airbag light and has four straightforward stages that are simple to complete.
First, activate the ignition. Wait for the airbag light to turn on next; it typically illuminates for seven seconds before automatically turning off. After waiting three seconds, immediately flip the ignition switch off. Before starting the engine, go through the basic procedures a couple of times. Your car’s airbag light should illuminate for seven seconds before turning off permanently if everything is done correctly.
In This Article...
Step 2: Use an OBD2 scanner to read the issue codes
Working with your airbag system is essential, therefore always use an OBD2 scanner to read the fault codes to determine where to begin troubleshooting. Never resolve the issue brought on by the airbag light before clearing the trouble codes. Continue the diagnostic by reading the codes to learn what might be the issue’s cause.
benvei
There is no doubt that you should check your airbag control module; something must have turned on that light. You might have harmed some of the yellow airbag wiring while installing your radio. I believe the airbag wiring to the passenger side airbag is located directly behind the radio.
With an OBD-II scanner that can examine the airbag module (not the $5 ones on eBay), you can reset the code. I don’t think it’s a smart idea to simply reset it without looking into what caused it. Personally, I wouldn’t interfere with the airbag system; instead, I’d let the dealer check it out to make sure everything is in order. OBD Scanners that can check ABS, Airbag, and other things are not cheap, so perhaps that is also the less expensive option.
Airbag Light Stays On in a Hyundai Santa Fe: Diagnosis
The computer system in your Hyundai Santa Fe performs a self-diagnostic check on all major systems each time you turn it on. A diagnostic warning light for the associated system will appear on the dashboard if any of these checks are unsuccessful. The airbag light will come on if the airbag system fails this test.
You might see something along the lines of SRS, a picture of a human with the airbag deployed, or the term airbag, depending on the model year and the nation you happen to be in. Consider each of these to be an airbag light.
The airbag light on your Santa Fe is there to alert you to an issue with the airbag system. It is perfectly normal and a standard part of the diagnostic cycle if it turns on briefly as the car begins. When it stays on, though, there might be an issue.
Can my airbag be reset?
After receiving your repaired module from us, you won’t need to take it to the dealership for additional programming because we reset all fault codes.
Except for modules that were harmed by a flood, fire, or another type of hardware damage, all airbag control modules can be reset and reprogrammed.
Accident-related hard and soft codes are stored in airbag control modules. The module that activates the airbag light will keep error codes even after minor incidents. To turn off the airbag light, we reset and erase all of these crash codes from the computer module.
Is a reset of the airbag light necessary?
The airbag warning light could come on as a result of a sensor malfunction or accidental travel. It will be necessary to reset the system and examine the sensors. The purpose of the airbag clock spring is to preserve continuity between the vehicle’s electrical wiring and the driver-side airbag.
How can I check the code on my airbag light?
Diagnostic Codes for Airbags The airbag codes consist of two digits. To read the codes, count the flashes the light makes, then count them again after the pause. For instance, two flashes, a pause, and four flashes indicate a code 24 issue with your airbag system.
What is the cost of turning off an airbag light?
Reset Airbag Light, at No. 1 Although it typically costs a few hundred dollars and takes several hours, depending on the type of automobile it might cost as much as $600.
By removing the battery, is it possible to restart the airbag light?
Without a scanner, most automobile models make it difficult to reset the airbag light. This is a safety warning since, when the airbag light appeared, you should always fix the problem. Fortunately, if you fix the issue, the airbag light will typically also turn off by itself in many automobile models.
However, in some older vehicles, the airbag light can be reset without a scanner by disconnecting the battery wires.
Make that there are no loose wires or rust in the connector plugs in the wiring system under the driver’s or passenger’s seat. Restart your car after spraying an electronic cleaner on the connecting plugs.
If you can’t detect any issues there, you should really invest in an OBD2 scanner or have a shop interpret the codes because otherwise you’ll have to guess what the issue is.
Why is the flashing passenger airbag light on?
A light on your instrument cluster turning on, or worse, continuing to blink, is one of the most annoying things that may happen. Please allow me to explain what you can do to disable the airbag light if you are having this issue personally.
It’s crucial to first understand why your car’s airbag light initially illuminated. There are several causes. It can indicate that your battery backup is dead, that your airbag clock spring is broken, or that the SRS airbag control module is malfunctioning. It might potentially indicate a problem with your impact sensors or seat belts. Whatever the cause of the airbag light may be, the major concern you should have is that unless the problem is resolved, your airbags won’t deploy in subsequent collisions. This implies that every time you get in your car to drive, you put yourself at risk for harm or perhaps death.
How long does the airbag module reset take?
You can send your airbag control module if your car was in an accident. Within 24 hours, it will be shipped back to you after being reset to its factory settings. When you receive your original module back after having it reset, it will be plug-and-play. Rarely, the module may need calibration or programming when it is put back in the car if there are hardware problems or if it needs to be programmed as new. Your money is fully guaranteed with our service. Save money by placing your order right away!
What may make the airbag light continue to illuminate?
A problem with the seatbelts or airbags is indicated by the airbag light. Therefore, it’s usually not a good idea to drive when the airbag light is on. We advise having it towed to the dealership rather than driving it yourself if it remains illuminated in your car.
Where is the switch for the passenger airbag?
If the vehicle has a switch called the Passenger Airbag Cut Off Switch, it can be used to deactivate the passenger airbag (PACOS).
When the passenger door is open, you may access the switch for the passenger airbag on the passenger side of the instrument panel.
ALL FRONT-FACING PASSENGERS (CHILDREN AND ADULTS) CAN SIT SAFELY ON THE PASSENGER SEAT WHEN THE AIRBAG IS ACTIVATED.
Rear-facing child seats are safe for use on the passenger seat when the airbag is switched to OFF.
Can an OBD scanner turn off the airbag light?
Two categories of codes exist:
- Unhard Codes
- Precise Codes
Yes, most scanners allow you to delete soft codes after a problem has been fixed. These codes represent a malfunction with an element or component of the SRS system, such as
- vehicle airbag codes
- codes for seatbelts
- coded impact sensors
No, scanners are unable to remove these codes. These codes, which are also known as crash data, are kept following a car accident. These codes are also hardware error codes.
Is the airbag fuse removable?
The airbag cannot be turned off by removing a fuse; even if it had one, which it does not, doing so would not turn it off. Cutting or twisting the wires or changing the impedence won’t make it work either; after all, the equipment is fail-safe.
Will the airbag light turn on if a fuse blows?
Only if the blown fuse is directly connected to the airbag system may it cause the airbag light to turn on and off. Although this is the primary reason for this light, other problems can cause an airbag light to suddenly come on.
The airbag system can malfunction, you can interfere with the seat belt sensor, there is a broken clock spring, there is damaged cabling under the seat, the computer system receives incorrect data, or the sensor was damaged in an accident, which can cause the light to turn on and off.
Driving with the airbag light on is it forbidden?
In some vehicles, it is even possible to turn off the passenger airbags, which will make your dashboard’s airbag light come on.
You should only deactivate the passenger airbag when absolutely necessary because, as was previously said, airbags are an essential safety element.
If your airbag light ever illuminates for no apparent reason, you should try to resolve the situation.
What is the price of replacing an airbag sensor?
Depending on the automobile model and labor charges, the cost to replace an airbag sensor ranges from $100 to $600. A sensor for an airbag costs between $50 and $300, as does the labor.
Both the airbag sensor and its replacement are delicate parts. Even for an expert, correctly diagnosing and installing the airbag sensor can take up to two hours.
The airbag sensor itself is typically not very expensive; you may anticipate paying between $50 and $300 for a brand-new one. Avoid taking the chance by always purchasing OEM original, genuine products and never aftermarket sensors.
You can save money by replacing the airbag sensor yourself if you are highly confident working on cars and meticulously following the repair manual.
If you have even the least qualms regarding the replacement, have a pro handle it.
Keep in mind that it is a crucial component, therefore installing it properly is important in case of an accident. Additionally, if you make a mistake, there is a chance that all of the airbags in the automobile would deploy, costing thousands of dollars to repair.
How much does servicing an airbag run?
The cost of replacing an airbag can be significantly more than the airbag itself. They take a long time to replace, and the cost of replacing all the linked parts adds up quickly.
Expect to pay, on average, between $1,000 and $1,500 for each replacement airbag. Just the airbags themselves are included; other parts that require replacement are not. A replacement airbag module will cost an additional $600 and above.
Therefore, if your driver’s and passenger’s front airbags have deployed as a result of a frontal collision, you should budget about $3,000 to repair your airbag system. Getting your car roadworthy goes above and beyond bodywork! Is it cheaper to sell your car instead of paying these expenditures to fix it?
Of course, the overall cost of repair for replacing your airbags and/or your instrument panel may vary based on the year, make, and model of your car. As an illustration, the cost to repair the driver-side airbags on a Ford F150 ranges from $200 to $700. The cost of replacing the side passenger airbags in a Honda Civic ranges from $400 to $1,000. Depending on the manufacturer, cars like BMW, Nissan Altima, Toyota Camry, and others may be expensive or affordable.