A CR2032 battery powers the majority of Hyundai key fobs. Once you have a new Hyundai key fob replacement battery in your possession, insert it into your key fob exactly where the old one was. Check to see if the battery is in contact with each connection.
In This Article...
In a Hyundai key fob, what kind of battery is used?
The battery in your Hyundai key fob is simple to change. A replacement CR 2032 3V battery is all that is required. They typically cost between $3 and $5 for a pack of 5. Wearing latex gloves is advised because you will be contacting a motherboard during this process, which could result in unintended harm.
- Remove the emergency key from the fob’s base.
- Between the release button and the key slot, insert the key.
- Turn the key until the fob pops open as if you were unlocking a door.
- Open the fob while facing the buttons downward (otherwise they will fall out).
- Remove the barrier and motherboard, then set aside the button-side of the fob.
- Remove the dead battery from its mount using the key.
- Place the + side of the new battery in its bracket.
- Replace the fob’s button-half, motherboard, and barrier.
- Set the release button peg in the appropriate hole.
- Reassemble the fob with a snap.
You’re done now! Press any button to put your Hyundai Smart Key to the test. If all was done correctly, a tiny red light should flash over the unlock button.
I can’t get my Hyundai key fob to open.
You must first depress the metal button or tab to release the actual key before you can open the key fob on a Hyundai. The fob will then pop open once you insert the key into the hole and move it around. Despite being somewhat high-tech, your key fob is robust.
How much does a new Hyundai key fob cost?
It’s more likely that you will be allowed to utilize an aftermarket key fob if your automobile is at least ten years old, according to CR’s Ibbotson. Many of these less sophisticated fobs can be configured by the consumer, a local technician, or an automotive locksmith.
Ibbotson advises making sure to phone your neighborhood garage first to confirm that they can do the task, as key-fob programming equipment levels can vary from shop to shop. For instance, a Maryland-based repair shop called Murray’s Auto Clinics informed CR that they are unable to program key fobs for any vehicle with push-button start or keyless entry.
We took our vehicle to M.J. Sullivan Hyundai in New London, Connecticut, where we were charged $120 for programming (one hour of labor), which is what they would have charged us if we had purchased the key fob from them.
Hyundai sent us a laser-cut mechanical backup key for $72.47, bringing the total cost to $272.42 (the car waited at the shop for two days); if we had ordered the key fob through the store, the total would have been $428.92).
For some makes and models, you can purchase a cheap aftermarket fob and program it yourself if your home unexpectedly gains a third driver, such as a teenager.
We purchased a fob from BestKeys from Amazon for CR’s 2008 Chrysler Town & Country minivan. Although it lacks the Chrysler branding on the back, it resembles the two original fobs that came with the minivan when it was new. The uncut mechanical key and internal circuitry were both included in the $14.30 price. (However, we didn’t see the need to shell out the cash to have a locksmith cut that third key.)
Chrysler customers can program a third key fob themselves if they already have two functional ones, just like GM owners can. The owner’s manual contains clear and straightforward programming instructions.
Why won’t my key fob operate now that the battery has been changed?
The most typical fix for a broken key fob is a battery replacement. However, replacing the batteries may not always be the best course of action. Therefore, your key fob might not operate even after a battery change for various reasons.
Handling the key fob circuit carefully is the first step in fixing the issue. Do not use your bare hands to contact the key fob circuit if you are not familiar with handling electronics. Call a professional right away to quickly diagnose and resolve the issue.
The following are additional causes for the key FOB’s malfunction:
Over time, a car remote’s button will inevitably wear out. When the button is depressed, the contacts notify the circuit board to carry out commands. The contacts may become separated from the buttons as they deteriorate. Pressing the buttons repeatedly is one of the greatest techniques to identify worn-out car buttons on car remotes.
Determine which of the following circumstances applies:
- Only certain button presses, or all button presses, function.
- One button operates while the other does not.
There is a problem with the automobile remote if the plastic that covers the key fob has also cracked. Open the key fob using basic tools, then inspect it for damaged contacts or crooked buttons. In the event that doesn’t work, get a new automobile key fob.
Your car remote might not function after changing the battery for another cause, which is the lock. Look for these indications to determine whether the lock or auto door has become faulty.
- Manual or key operation of the lock does not cause it to unlock or lock.
- Some door locks can be opened remotely, but not all.
- Without the doors opening, a signal has been transmitted, as indicated by the indicator light flashing.
- Door lock operates partially or not at all.
The automobile key may become damaged as a result of things like water, scratches, etc. The key fob may be damaged if it stops functioning right away after being trodden on, submerged in water, or opened. Other indicators to look out for include:
- Whether a backup key functions
- The buttons are stationary.
- The Key is clearly damaged.
A damaged key can be replaced with a new car key. The key fob can be reprogrammed with assistance from the Colorado Springs Locksmith specialists.
There is a good likelihood that the battery change reset a car remote. When certain buttons are pressed, the key fob can also be reset. Therefore, the failure of many key fobs is a good indication that the automobile key remote has been reset. There are two indicators to watch out for:
- No spare remotes operate.
- car remote completely quits functioning
After changing the battery, does the key fob need to be reprogrammed?
After changing the battery, you typically do not need to reconfigure the key fob. However, you might need to reprogramme it by re-pairing it with your vehicle if you’ve replaced not only the batteries but also some of the internal cabling and electronics.
How is a key programmed after a battery change?
Turn the key back to the “Off” position while holding down the lock button on the fob. At least three times, go through this process, finishing with the key in the “On” position.
This notifies the electronic control modules in your automobile that the signal is coming from your key in the ignition, and it then saves the information.
How is the Hyundai Smart Key pry opened?
To remove the metal key, push the metal button next to it. Open the Hyundai key fob by inserting this key into the little opening in the rear.
Hyundai vehicles can be operated without a key fob.
Once the engine is going, the automobile will still work without the key fob. Additionally, switching from park to drive is trouble-free even when the key is not available.
Key fobs: Do they have batteries?
The past ten years have seen a significant development in key fobs. Push start systems of today are an evolution of what was once only a convenient technique to remotely lock and unlock doors. Despite the fact that key fob technology is continually evolving, their power source has not changed. Batteries power key fobs and other auto remote controls. That implies that the battery inside them needs to be changed when it runs out of juice. Batteries Plus can assist if your key fob isn’t working as well as it once did. For answers to all of your questions about automobile remotes, including what kind of batteries they need, how long they last, and where to buy a replacement battery, continue reading.
Can you use the key to start a Hyundai?
Using your Android smartphone and the Hyundai Digital Key system, you may unlock and start your car. This article will walk you through the setup and usage of the Digital Key system if your Hyundai has it.
The following are the requirements for setting up a Hyundai Digital Key:
- a smartphone running Android. The Digital Key system is currently only compatible with Android phones. The phone needs to fulfill the following criteria:
- Android 7.0 or later operating system
- 4.0 or later for Bluetooth
- Near-Field Interaction (NFC)
NOTE: The utilization of Digital Key capabilities will be restricted if the device only supports NFC or BLE.
You have signed up for the Hyundai Digital Key service and have a MyHyundai account. The link between your phone and the Vehicle Identification Number of your automobile is formed through MyHyundai (VIN). Make sure your new Hyundai is listed in the car list if you are presently a MyHyundai member and it is equipped with a Digital Key.
Install the Hyundai Digital Key app on your phone after downloading it from Google Play.
with the aforementioned factors covered. The first step is to launch the Digital Key app and follow the on-screen instructions to enter the necessary data. The 4-digit PIN for your MyHyundai account will also be used by the Digital Key app.