How To Reset Brake Light On 2009 BMW 328I?

BMW / By
  • Start the ignition, but do not drive. Press the START button if your BMW has one without depressing the brake pedal.
  • Ensure that the time is displayed in the instrument cluster’s center.
  • The ODO reset button should be pressed and held for roughly five seconds. The dash will first display a yellow triangle. Hold the ODO reset button down until the subsequent symbol appears.
  • When the symbol for the front or rear brakes appears, repeatedly press the ODO reset button. Depending on the sensor you want to reset after replacing.
  • When the preferred brakes’ symbol appears on the screen, press and hold the ODO reset button until the word “RESET” appears beneath the symbol.
  • Release the button immediately when the word “reset” appears beneath the brake symbol, then press the button once again. Holding the ODO reset button down will make the brake light go out.
  • The kilometers should become ——-, signifying that the reset was successful. Although these intervals may vary between models, the next time you should have your BMW brakes changed is at 25000 miles for the front brakes and 31000 miles for the rear brakes.

Why is my BMW 328i’s brake light on?

The brake warning light is a major matter. When you see it turn on, ensure sure your emergency brake is not engaged, then halt your vehicle as soon as you can. Your brakes could not operate at all if you have insufficient brake fluid.

On a BMW, how do you turn off the brake light?

Can the brake light on a BMW 1 Series be reset? Last week, I had my brakes tested, and new brake pads were put. However, my car’s light is still on.

In less than two minutes, find out if your auto insurance is being overcharged.

Absolutely! Since your brakes have already been inspected, you should feel comfortable turning the brake light back on. The majority of maintenance lights require manual resetting when the task is finished. You must take the following actions to reset the brake light on your BMW 1 Series:

  • Press the odometer reset button on your dash after turning the ignition to the ON position.
  • Keep pressing the button. A yellow triangle with an exclamation point inside will be seen on your display. The service menu will then appear.
  • To discover the brake light setting, use the turn signal stalk.
  • To reset the light, press and hold the BC button on your turn signal stalk.

Examine your insurance alternatives with Jerry to make sure you’re prepared financially in case of an accident. The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.

How can my BMW 3 Series be reset?

The mechanic will reset the computer in your BMW after the service is complete so it can record your mileage and let you know when the car will need maintenance again in the future. However, the techniques listed below can help you if you maintain your own car but are unclear of how to reset the computer system.

  • With the engine off, turn the key to the ON position.
  • For TEN seconds, press and HOLD the ODOMETER button. It can be found at the Instrument Cluster’s extreme bottom LEFT corner.
  • The dash screen will display FGSTNR along with a number. Your chassis number is this.
  • The LAST FOUR numerals are added. Ex: 3+4+5+6= 18 Your UNLOCK CODE is going to be 18.
  • Press and hold the ODOMETER button one more until the FGSTNR clearing area appears.
  • Press the odometer button until the upper Menu area (entering code menu) reaches 19 after the bottom area has cleared; When you do, the text will appear at the bottom: Press the odometer button to enter your unlock code after turning the lock on. This is seen in the bottom portion.
  • The screen will appear as in the image above after a little period, at which point the menu will once again appear at the top. To access the number 21 menu, press the odometer button.
  • On the screen’s bottom, it will say: RESET? To complete the reset, press the odometer button.

Your BMW’s computer has been restarted! The existing settings must now be added again, or new ones must be added.

**NOTE: Slowly repeat the procedures if you are unable to reset the BMW computer on your first attempt. If you’re still having trouble, ask the dealership for help or refer to your car’s owner’s manual.

What does the BMW’s yellow brake light signify?

I continually receiving a triangle on my dash with an exclamation point and a yellow brake light. It randomly starts up and then shuts off. They topped out the brake fluid after I took it to the dealership to have it checked. but it’s now turning back on. Anyone with knowledge of the issue? thanks.

So, since the dealer filled it off, have you checked the brake fluid level again? You may have a brake system leak if your braking system required enough fluid to trigger the low brake fluid light. How does the pedal feel? When you apply consistent pressure, does it sag at all? When you overnight park, are there any moist areas close to the inside of the wheels?

I didn’t check the amount of the brake fluid. How can I go about doing that? Normally, the pedal feels. Lighting turns on and off. I therefore assume it is the sensor.

There is a sizable black plastic cover on the driver’s side beneath the hood, just where the gas strut—which keeps the hood up—attaches to the body. Both a front and a back clip are present. The brake fluid reservoir can be seen there if you lift it off.

Although I too prefer my eyeballs to any fluid level sensors (crankcase sump?! ), a YELLOW brake indication, according to the table in the non-iDrive handbook, indicates that the brakes are engaged “Drive-off assistant is not working. After the brake is disengaged, the car won’t be kept in position.” A red sign would be low fluid.

What does the BMW’s red brake light mean?

The amber/yellow brake warning lamp and the red brake warning lamp have different functions. When there is a hydraulic issue, such as low brake fluid or a loss of hydraulic pressure in one of the brake circuits, the red (RBWL) lamp will illuminate. If the parking brake is applied or shorted to the ground, it also glows.

If the brake fluid level is low, it lights. Low fluid level is frequently a sign that the brake pads need to be replaced since they are worn out. Brake fluid accumulates in the space behind the caliper’s piston when the brake pads deteriorate. Before adding fluid to the reservoir, it is crucial to inspect the system for leaks.

What should you do if your brake light doesn’t go off?

One of the most crucial parts of a car is its brake lights (or taillights). They make use of a switch that activates the bulbs when the brake pedal is depressed. Brake lights flash when you are ready to slow down or stop, alerting any vehicles behind you. However, when they become stuck, these lights lose their function as a safety feature and may endanger both you and other people.

Circuit failures, issues with the brake assembly, and low brake fluid levels are some of the most typical causes of brake lights that remain on. While some problems are easy to diagnose and resolve, other problems are brought on by untidy auto parts.

Here are some typical solutions for brake lights that won’t go off:

  • Check for damage on the brake light switch.
  • Putting out blown fuses
  • replacement of the brake light switch
  • Keep the brake pedal bumper in working order.
  • Change any burned-out bulbs.
  • Remove the vehicle battery.
  • Keep the brake pedal clean.
  • Make sure the brake pedal effectively activates the switch.
  • Ensure that your brake sockets are spotless.
  • Don’t reduce your BCM.
  • have enough brake fluid
  • Turn off the parking brake.

The most popular solutions to brake light sticking are listed in this article. If necessary, it also explains how to replace your bumper and brake light switch. Stay tuned to discover more about how to maintain the appropriate operation of your car’s safety features, which is what this article seeks to provide for vehicle owners.

How can the service light be turned off on a BMW?

  • Start the electrical systems of the car, but do not start the engine.
  • Till the service notice shows, press and hold the tiny odometer button in the instrument panel’s lower left corner.
  • When the message says “Reset,” let go of the button and press and hold it once more.

How can I turn off the dashboard brake light?

RISK: Despite changing the brake pads and associated wear sensors, the dashboard braking system warning light continues to flicker. Steps to take:

  • To check that the brake pads and discs are in contact, repeatedly press the brake pedal.
  • Turn off the dashboard for a brief period of time.
  • Check to check if the light is still on after turning on the dashboard once again. Ask for help and guidance if the brake warning light is still on.

Only for entertainment and informational reasons, the information in this article should not be used as a substitute for consulting a qualified technician or mechanic for expert guidance. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.

How come my emergency brake light won’t turn on?

A number of dashboard warning lights may suddenly begin to illuminate. Everyone is aware of the functions of the battery and oil lights, but many other lights call for consulting the owner’s manual. To assist make things a little clearer, we’ll look at several lights and what they represent in the upcoming months.

The parking brake warning light is displayed here. It can be either red or orange, depending on the brand of the car. It flashes to indicate that the parking brake or emergency brake is applied and needs to be disengaged before moving on with a drive.

It indicates that you need to add brake fluid if it stays lit after the parking brake is released or if it flashes intermittently while you’re driving. You must get the braking system checked if you check the fluid, add as necessary, and the light doesn’t go out.

In fact, you should get a brake inspection regardless of whether there is a leak in your brake system. Why? As your brake shoes or pads deteriorate, more fluid is needed to press them against the rotors or drums to stop the car. This dashboard light can be gently alerting you that brake servicing and repairs are about due.

The parking brake needs maintenance if there is an illuminated wrench under the light. The car can be operated safely, but it needs to see a mechanic.

Is your parking brake in need of repair? Go to any of the nine Auto Select auto and truck repair shops in Appleton, Green Bay, Stevens Point, and Weston.

BMW brake sensor replacement necessary?

The “brake” light on your dashboard or iDrive system is controlled by your BMW brake pad sensor, which also informs you of the remaining life of your brake pads. The sensor is mounted to the brake pad; as soon as the brake pads are completely worn down, the sensor’s tip breaks, tripping the wire and turning on the dashboard light. The brake pad sensor error codes are as follows when using an OBD scanner:

5, 5, 6, 5, 14, 5, 15, and 6F12

Every time you change your brake pads, you should also replace the brake pad sensor. The sensor does not need to be changed every time, but failing to do so could lead to erroneous readings of the amount of life left in your pads and a persistent notification on your dash/iDrive system. The only way to get rid of the light once it appears on the dash is to either swap out the sensor or bypass it, which will stop it from reading the pad life.