For this car, there is no onboard programming process. To program the keyless remote for this car, additional equipment must be attached to the vehicle.
Before going to the dealership, try a locksmith; their prices are typically 50% lower. Use the suggested locksmith locator on our website to find a preferred locksmith nearby:
The foot well area on the driver’s side is where the receiver module for setting the code is situated. close to the fuse box. Look for the tiny box with the “OFF” and “SET” switch on it.
Move it over to “SET” with a screwdriver; the ignition need not be turned on.
Then, press any button on your new remote, whether it says lock or unlock. Even if your old remote is functional, you must perform the identical action with it while the switch is set. While the switch is in the SET position, program each of your key fobs individually.
Take note of your vehicle identification number (VIN) and call or, better yet, visit your local dealer to inquire about any recalls that may have affected it. Mention that you would like to have a key fob installed, and the dealer may offer to do so without charge. Just stop by during the day and be friendly. Keep in mind that all employees at the dealer are salesmen because without sales, none of them would have a job.
It’s possible that this won’t work, but there’s no harm in giving it a shot. You’ll be astonished at what treating the service department well can do for you!
Was this Knowledgeable? Please spare a second to Like, Follow, and Share on the social networks listed below. People like you aid in getting the word out about us. It is extremely beneficial! We appreciate you coming and spreading the word to your loved ones.
In This Article...
For a 2011 Hyundai Santa Fe, how to program the key fob
Nonsense. On my 2011 Santa Fe Limited, I recently programmed a new remote start fob, and it performed well. See what occurs by following the steps listed below. 1. Open the door on the driver’s side. 2. Set the ignition of the car to the ON position (Do not start the vehicle) 3. Find the program/disarm button. It is on the electrical harness, right inside the lower dash, if you look attentively. It might be just under the fuse cover.) 4. The disarm/programming button must be pressed and held for 10 to 15 seconds before the alarm will beep three times. Release the programming/disarm button. 5. To activate the horn, push the Find/Panic button on the fob once. 6. Turn off the ignition of the car. YOU ARE DONE.
Step 3
When the car’s lights start to flash, press and hold the “Open” or “Unlock” button on the keyless entry FOB. Your Hyundai vehicle has now been reconfigured to the keyless entry FOB.
- Only Hyundai keyless entry FOBs that have already been programmed can be reprogrammed using these keyless entry FOB programming instructions.
- Toyota key
- Keyless entry FOB previously programmed for a Hyundai
- Not all Hyundai car models may be compatible with these setting recommendations. For assistance with programming a keyless entry FOB for a specific model, speak with your nearby Hyundai dealership or service center.
How is a key fob for a 2006 Hyundai Santa Fe programmed?
1. Turn the memory switch to the Off position and remove the plate covering the alarm system control located under the steering column. (The control module is the black box adjacent to the hood release that is located behind and below the fuse box. The vehicle in the image below has remote start; yours might not. You have found the box if it reads security system.)
2. Put the key in the ignition and switch it to the “On” position. Turn the memory switch to the Set position after waiting five seconds. Note: In some vehicles, the memory switch can be set without the key being inserted.
3. On the remote that is being programmed and on all additional remotes, press lock.
4. Switch off the ignition and flip the memory switch to the off position.
5. Replace the alarm plate, then test the remotes.
Want a professional to configure the remote for you since you’re having problems doing it yourself? Find a qualified key fob installer in your neighborhood by typing your city or zip code in the search box below.
How can my Hyundai remote be programmed?
- As soon as you get inside your Hyundai, check that all the doors are closed.
- Put your Hyundai’s ignition in the “ACC” (accessory) position using your key.
- Keep pressing the “open” or “unlock” button on the key fob until the light on your car starts to flash.
- Congratulations
Is the key to a 2007 Hyundai Santa Fe chipped?
We have your back! A transponder, a type of embedded microchip, is present in this key. Each transponder has a distinct code that serves as the key’s “fingerprint.”
Without the original, how do you program a keyless remote?
After locking every door, turn the ignition off. Set the accessory or “ACC” position on the ignition key. The door locks will cycle once once you turn the ignition key off once more. To program the key fob, press any button three times straight.
I need help pairing my Hyundai key.
It is recommended that you always keep your NFC (Near Field Communication) Key Card on hand as a backup key in case your smartphone experiences a power outage or other problem. The card resembles a hotel key card and may therefore be conveniently stored in a wallet or billfold. The NFC Key Card will also need to be associated and registered with the automobile in order to function as a backup digital key. If the card hasn’t already been associated with the car, please follow these steps:
- Start your car.
- Make sure the Hyundai Digital Key app is installed on your primary smartphone and that it is in the car.
- Pick Pair NFC Key Card through BLE from the side menu in the app.
- the wireless card changer with your card in it.
- There will be automated pairing.
Follow these steps to finish the registration procedure for models having a navigation screen:
What is the cost for programming a key fob at Hyundai?
It’s more likely that you will be allowed to utilize an aftermarket key fob if your automobile is at least ten years old, according to CR’s Ibbotson. Many of these less sophisticated fobs can be configured by the consumer, a local technician, or an automotive locksmith.
Ibbotson advises making sure to phone your neighborhood garage first to confirm that they can do the task, as key-fob programming equipment levels can vary from shop to shop. For instance, a Maryland-based repair shop called Murray’s Auto Clinics informed CR that they are unable to program key fobs for any vehicle with push-button start or keyless entry.
We took our vehicle to M.J. Sullivan Hyundai in New London, Connecticut, where we were charged $120 for programming (one hour of labor), which is what they would have charged us if we had purchased the key fob from them.
Hyundai sent us a laser-cut mechanical backup key for $72.47, bringing the total cost to $272.42 (the car waited at the shop for two days); if we had ordered the key fob through the store, the total would have been $428.92).
For some makes and models, you can purchase a cheap aftermarket fob and program it yourself if your home unexpectedly gains a third driver, such as a teenager.
We purchased a fob from BestKeys from Amazon for CR’s 2008 Chrysler Town & Country minivan. Although it lacks the Chrysler branding on the back, it resembles the two original fobs that came with the minivan when it was new. The uncut mechanical key and internal circuitry were both included in the $14.30 price. (However, we didn’t see the need to shell out the cash to have a locksmith cut that third key.)
Chrysler customers can program a third key fob themselves if they already have two functional ones, just like GM owners can. The owner’s manual contains clear and straightforward programming instructions.
Are chip keys available for Hyundai Santa Fes?
To start the vehicle, press the “start” button on your dead key fob as shown in the illustration.
With your key fob, press the “Start” button to start your Hyundai Santa Fe. The key fob’s chip is recognized by the car’s computer, which then approves the operation.
In this manner, you may still start your car even if the key fob battery dies.
How do I make my Hyundai smart key functional?
You must already have a MyHyundai account set up and the Digital Key app downloaded on your phone in order to use Hyundai Digital Key. If you’ve already completed these steps, make sure you have the Digital Key Smart Card that was provided when you bought your Hyundai vehicle on hand.
- Go to the Digital Key app’s primary menu.
- If your Hyundai isn’t already running, start it.
- Press the + button to begin pairing in the Digital Key app.
- Your Android device should be placed on the wireless charging pad.
- Await the phone to complete pairing.
Once you begin the pairing process, this procedure will finish on its own.
- (For Hyundai models lacking a navigation system) Choose the following choices on the instrument cluster display of your Hyundai car, in this order: Smartphone Key, Digital Key Choose, Save
- (Applicable to Hyundai cars with navigation) Choose the following choices on the navigation screen of your Hyundai vehicle in the following order: setup, vehicle, smartphone key, digital key, pick, and save
That’s all, then! The Digital Key app for smartphones is now functionally equivalent to a Smart Key fob.
Hyundai smart keys—can they be reprogrammed?
Hyundai vehicle keys can be reprogrammed with the most recent Snap-on software. Select Smart Key Code Saving from the System menu, then select it again on the following screen. Press Continue when the screen prompts you to carry out the action with the ignition key off.
Can a key fob be programmed without visiting the dealership?
Can a key fob be programmed without visiting the dealership? Yes, you can program the key fob’s locking and unlocking features without visiting the dealership. However, you might need to visit the dealership or a locksmith if you need to program the transponder in order to be able to start the car with the key.
How do you use a dead key fob to open a Hyundai?
This information caught my attention. I think it would also benefit our Palisades!
Fix 1: While tapping the brake, push the Start button using the rear or end of the dead key fob. Fix 2: Place the dead key fob, buttons facing up, in the Smart Key slot (located in the locations specified below), and depress the brake while pressing the Start button.
Slots for Smart Keys: There are three places where these slots can be found: 1. on the front of the center console; 2. behind a panel right below the infotainment control knob; or 3. on the left side of the glovebox when it is open.
Hyundai began using transponder keys in what year?
With the widespread use of autos, cars have developed into significant personal possessions. It is therefore crucial to protect my car from crimes like theft. The automobile key served as a crucial instrument in this situation because it was required to start and enter the vehicle. The key functioned as a security system password since it was engraved with a distinctive pattern.
However, these keys had a flaw: they were simple to copy. To solve this issue, technicians carved a distinctive design into the interior, not the surface, of each key. The immobilizer technology then emerged in 1994 and provided a more basic remedy. A key with immobilizer technology has the same appearance as a standard key, but the handle of the key has been implanted with an encrypted chip known as a “transponder.” The engine could start when the electronic control unit (ECU) of the car verified the data on this chip. In other words, even though you had the same key, you couldn’t actually drive the automobile. Automobile immobilizer technology continues to be a crucial security feature.