That seems annoying. Fortunately, replacing the battery in a key fob for a BMW 328i is not too difficult. Here’s how to go about it:
- Start by pressing and holding the little button at the key fob’s base. You can do this to take the metal key off of your key fob.
- Find a small hole by feeling around the key fob’s edge. Use your metal key or a small flathead screwdriver to remove the key fob’s back plate off.
- Remove the old battery with care. You must orient your new battery in the same direction as your old one, so be sure to take note of where the negative and positive terminals are located.
- Put the key fob’s fresh battery in there. As you do this, try to avoid touching the terminals because doing so could shorten the key’s battery life.
- Replace the back panel last. The two parts should click together when they are joined properly. After that, you may test out your new key fob batteries by inserting the metal key.
Why not use the extra time to explore your options for auto insurance using the Jerry app while you’re changing the battery in your car remote? Simply download the app, respond to a few short questions, and you’ll see a list of affordable estimates from companies like Nationwide and Safeco.
In This Article...
Procedure
The metal blade key must be taken out of the fob. To open the key fob, use the metal key as a pry bar.
- Turn over the BMW remote. On the back of your BMW key, look. Under the back cover is where you’ll find the BMW key battery.
- Get rid of the battery cover.
- Delete the previous battery. To remove the battery, simply lift it out of the way.
- Replace the battery in the BMW key. Replace the old battery in the BMW key with the new one. Never force the battery into position. Use only light pressure when handling the battery.
- Put the remote away. The remote’s cover can be snapped back on.
Can you change the battery in your own BMW key?
Although the battery in this key is not intended to be changed, it can be done by cutting the casing apart and soldering a new battery. You’ll need a VL2020 battery to swap out this BMW key battery. The manufacturer does not advise performing this operation.
How much does a new BMW key battery cost?
I recently visited the business. The key fob wouldn’t work to lock or unlock my car when I tried. My BMW key fob’s battery has to be changed.
In less than two minutes, find out if your auto insurance is being overcharged.
Batteries for key fobs typically last three to four years. Your current BMW key fob might need to be replaced, depending on the model.
You should replace the battery in your smart key or Comfort Access BMW key fob by following these simple instructions:
- Get a CR2032 battery from a department or auto store. It will cost you around $2 to buy it.
- By depressing the tab on your key fob, you can take the valet key off.
- To pry open your battery cover, use the key or a flathead screwdriver.
- Replace the old battery with the new one after removing the old one.
- Restore the key to its housing and close your key fob.
You have a non-comfort access key fob if you are unable to open it because it has an indent in the side. You must take a long drive to recharge your key fob battery because it can only be done through the ignition of your automobile.
Once the battery has been successfully replaced or recharged, make sure to test it by locking and unlocking the doors several times. To find out how much you can save on your auto insurance before you leave again, take a moment to glance at the Jerry app.
The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
Why won’t my BMW key fob function now that the battery has been changed?
A dead battery is the most frequent cause of a key fob not functioning. Having said that, your keyfob might be having more serious issues. You might require a key fob replacement or perhaps auto door lock repair if your key fob stops operating after a battery change.
The BMW x3 key uses what type of battery?
The battery in your BMW key is a CR2032. the old BMW key fob batteries with care, then gently insert the new one after removing the key fob cover.
What occurs if the battery in your BMW key dies?
You won’t be able to use keyless entry or remote unlocking if your BMW has Comfort Access if the battery in your key fob has died. You can still enter and manually start your automobile, though.
Press and hold the key release button at the remote fob’s base while unlocking the door of your car, then slide out the internal key blade. This can be used in place of a standard key to unlock your car. You can locate a little hole on the bottom of the handle if the keyhole is hidden on your car door. Use the key blade to pry off the trim panel and expose the keyhole by inserting it into the hole.
Once you’re inside, put your remote key fob in the ignition slot or, if your car doesn’t have one, press it up against the steering column’s key markings. If your key fob dies, you will still be able to start your BMW using the start/stop button on the dashboard.
What kind of battery is required for a BMW key fob?
A CR2032 battery is necessary for BMW key fob battery replacement for drivers who have BMW Comfort Access. To replace the battery in your BMW key fob, follow these steps: Remove the metal valet key by pushing in the little tab on the side of your key fob.
What does a BMW key’s diamond button do?
Does anyone have any knowledge of what the key fob’s diamond button is meant to do?
The included manual is incredibly succinct. It refers to a “Headlight courtesy delay feature,” although it’s not entirely clear what this feature performs. “If the standby state is switched on and the high-beam headlights are enabled, the low-beam headlights remain on for an of time,” the text states. Even if “… for a period of time” is meant to be “… for a length of time,” that still doesn’t adequately describe what this feature is.
According to the description, it can only be used when the automobile has just been turned off and the high beams are on. However, when the car is locked, the button appears to have some effect. The inside lights occasionally come on. The headlights occasionally come on. It is quite unpredictable and challenging to duplicate.
What experiences do others have? Has anyone figured out what this button’s actual purpose is?
It is unfortunate that it cannot be set to perform things like open the windows or sunroof, switch on the heating, or other things!
Mine has two options (330e in Belgium): turn on the lights in the house or turn on the air conditioning. In the options for the car, I can select the default function.
It briefly illuminates the headlights in my automobile. Excellent for illuminating the path to your front entrance or finding your car at night in a big parking lot.
Check the “Home lights” setting under “Exterior Light Settings” on your iDrive to make sure it is not set to 0 seconds.
My headlights now turn on for 10 seconds when I hold the diamond button on the key because I set mine to that duration (G20 330i).
Do BMW keys automatically recharge?
While in the ignition, BMW keys are charged. Inductive charging will be used to recharge the key’s battery from positions 1 (KL R) and 2 (Run). Simply connect an automotive battery charger to your car’s battery pos/neg if you have a low battery and want to recharge the key without driving. Jump-start the engine bay terminals, then turn the ignition to position 1 and leave the car running over night. Your car’s battery won’t discharge while the key is being charged thanks to the charger.
The time it takes to drive 30 miles to recharge a dead battery To fully recharge the battery, allow 15 key pushes and 30 hours of driving in total.
Is a BMW key fob reprogrammable?
Take the BMW key fob you want to configure, hold down the unlock button, and then press and hold the BMW logo three times. The doors should lock and unlock once more. When this occurs, you are ready to go! You’ve set up your BMW key fob.
If I change the battery, do I need to reprogram my key fob?
After changing the battery, you typically do not need to reconfigure the key fob. However, you might need to reprogramme it by re-pairing it with your vehicle if you’ve replaced not only the batteries but also some of the internal cabling and electronics.
What if the smart key’s battery runs out?
Insert the new battery after removing the old one. Your Smart Key will be operational once you have put the key fob back together and replaced the metal key.