Could you please explain how to turn off the airbag light on my BMW X5? Every time I turn on my car, it has been coming on, and I have no idea how to turn it off. I’m hopeful that resetting the light will solve the problem.
In less than two minutes, find out if your auto insurance is being overcharged.
Unquestionably, resetting your airbag light is a solid first move. Observe these steps to reset the airbag light on your BMW X5:
- Upon starting your automobile, check to see if the airbag light is on.
- Then, after seven seconds, restart your vehicle.
- Two more times, repeat this procedure. Your airbag light ought to disappear.
It is advisable to have someone check over your car for you if the airbag light starts to illuminate once more. Given that sensors are frequently the subject of auto recalls, there may be an issue with the sensor or the airbag itself. The airbag will protect you and any passengers in the event of an accident.
The Jerry app makes sure you are prepared for the aftermath while airbag maintenance makes sure you are prepared for an accident.
The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
In This Article...
Procedure
- Under the dash, you may find the OBD-2 port. Scanners can be connected to OBD2 ports. A 20 pin OBD2 adaptor is required if your BMW was manufactured in 2001 or earlier.
- Start the engine. Avoid starting the car.
- Scanner will start up. On the scanner, choose your BMW chassis/model. We are using a Foxwell NT510 from the BMW scanner in this instance.
- Choose BMW – Body – Safety System control units. You may read Airbag Fault Codes by navigating to the Safety System/SRS control unit.
- Clear the airbag control unit’s codes. revisit the first menu. To access Clear Fault Codes, scroll below. On the following screen, click YES.
Step 2: Use an OBD2 scanner to read the issue codes
Working with your airbag system is essential, therefore always use an OBD2 scanner to read the fault codes to determine where to begin troubleshooting. Never resolve the issue brought on by the airbag light before clearing the trouble codes. Continue the diagnostic by reading the codes to learn what might be the issue’s cause.
Why is my BMW’s airbag light on?
What it appears to be: A passenger seated in a chair with a seatbelt fastened holding a circle in their lap. The “SRS” symbol is illuminated in the dash of some cars.
What it means is When a problem is identified by your BMW’s computers within the airbag control unit, the airbag system, or supplemental restraint system (SRS) light will illuminate. If the SRS warning light is on, the system has been turned off, and the airbags won’t inflate in the case of a collision.
What to do if it comes on: When a car starts up, this light will briefly illuminate in the dash before going off, signaling that everything is working as it should and making it safe to drive.
Check to see if anything is obstructing the seatbelt click switch or if anything is piled up behind the seat, which could harm the wires, if the SRS light remains illuminated after starting the car or while it is in motion. If nothing is discovered, visit a local independent BMW repair facility as soon as possible to have a professional inspect and identify the issue. This is not something to be taken lightly, and it is safer to get this issue looked at by a certified BMW mechanic than to jeopardize your safety and the safety of your passengers by driving while it is still active.
How to turn the light off: After you bring your BMW to your neighborhood BMW shop, your mechanic will examine the component and the wiring, run code checks, and perform any necessary repairs.
An illuminated SRS light may indicate a sensor issue, the need to reset your airbags (for instance, if you were recently in a collision and the sensors were activated but the airbags did not deploy), or an issue with the seatbelts. Checking car bulletins is a good idea because there may be other instances when your airbags need to be recalled.
How do I activate my airbag light?
The airbag light connects the seat belt system and the airbag system as part of the Supplement Restraint System (SRS) in automobiles. When you turn on your automobile, the airbag light comes on for around seven seconds before going out, signifying that the internal system check was successful and finished. When the airbag light either never turns on or stays on while blinking, an issue exists. The airbag light needs to be reset at this stage.
Examining seat belt components, fixing bad clock springs, and replacing faulty sensors are a few techniques for turning off an airbag light. New bulbs or a fully charged battery are other options. While most repairs can be done without a professional, others may.
The following 10 steps will reset your airbag light:
- Turn on and off your ignition.
- Test drive your car when it has been restarted.
- Check the airbag switch for the passenger.
- Check to see if the seat belts are in place and functioning properly.
- Check to see if the passenger seat sensor is off.
- Use a scanner with the ability to reset the SRS or airbag light.
- Fix the broken airbag sensors.
- Replace or repair a broken clock spring.
- Check to see if the airbag is working properly.
- seek for a specialist’s help.
Although not exhaustive, the list above includes tried-and-true methods for tackling the problem. Some of them might not apply to your vehicle because compatibility is always based on the year, make, and model. It is recommended that you have your service manual on hand when carrying out any of these fixes. Always follow the manufacturer’s recommendations, too. Let’s get started on resetting your airbag light right away.
What may make the airbag light continue to illuminate?
A problem with the seatbelts or airbags is indicated by the airbag light. Therefore, it’s usually not a good idea to drive when the airbag light is on. We advise having it towed to the dealership rather than driving it yourself if it remains illuminated in your car.
What is the cost of turning the airbag light back on?
Reset Airbag Light, at No. 1 Although it typically costs a few hundred dollars and takes several hours, depending on the type of automobile it might cost as much as $600.
Can the airbag module be reset?
After receiving your repaired module from us, you won’t need to take it to the dealership for additional programming because we reset all fault codes.
Except for modules that were harmed by a flood, fire, or another type of hardware damage, all airbag control modules can be reset and reprogrammed.
Accident-related hard and soft codes are stored in airbag control modules. The module that activates the airbag light will keep error codes even after minor incidents. To turn off the airbag light, we reset and erase all of these crash codes from the computer module.
How much does an airbag repair cost?
The cost of replacing an airbag can be significantly more than the airbag itself. They take a long time to replace, and the cost of replacing all the linked parts adds up quickly.
Expect to pay, on average, between $1,000 and $1,500 for each replacement airbag. Just the airbags themselves are included; other parts that require replacement are not. A replacement airbag module will cost an additional $600 and above.
Therefore, if your driver’s and passenger’s front airbags have deployed as a result of a frontal collision, you should budget about $3,000 to repair your airbag system. Getting your car roadworthy goes above and beyond bodywork! Is it cheaper to sell your car instead of paying these expenditures to fix it?
Of course, the overall cost of repair for replacing your airbags and/or your instrument panel may vary based on the year, make, and model of your car. As an illustration, the cost to repair the driver-side airbags on a Ford F150 ranges from $200 to $700. The cost of replacing the side passenger airbags in a Honda Civic ranges from $400 to $1,000. Depending on the manufacturer, cars like BMW, Nissan Altima, Toyota Camry, and others may be expensive or affordable.
How are the BMW dashboard lights reset?
Find the tiny odometer button in the instrument panel’s lower left corner. until the service message shows, press and hold. When the message says “Reset,” let go of the button and press and hold it once more.
By removing the battery, is it possible to restart the airbag light?
Without a scanner, most automobile models make it difficult to reset the airbag light. This is a safety warning since, when the airbag light appeared, you should always fix the problem. Fortunately, if you fix the issue, the airbag light will typically also turn off by itself in many automobile models.
However, in some older vehicles, the airbag light can be reset without a scanner by disconnecting the battery wires.
Make that there are no loose wires or rust in the connector plugs in the wiring system under the driver’s or passenger’s seat. Restart your car after spraying an electronic cleaner on the connecting plugs.
If you can’t detect any issues there, you should really invest in an OBD2 scanner or have a shop interpret the codes because otherwise you’ll have to guess what the issue is.
Which BMW models are having their airbags recalled?
According to Roadshow, 7,910 vehicles, or the 328is and 323i models from 1999, were affected by the faulty airbag issues in 2019. The 1999-2001 3 Series was one of the additional models. A total of 74,000 vehicles were impacted, of which 34,000 were 3 Series coupes from 1999 to 2000. Additionally, it’s possible that some of the 74,000 vehicles that had their airbags replaced during the previous recall still have these faulty ones.
In the early stages of the recall, Takata thought that replacing the outdated, lethal inflators would be the best course of action. On other car models, the problematic ones were replaced with new ones that had the same same chemical and design. Naturally, this didn’t work, and the explosive propellers were subsequently modified to protect airbags for a longer period of time.
Some automakers have suffered losses and chosen to purchase airbag inflators from other suppliers as a result of the flaws made by these manufacturers. Takata’s reputation suffered as a result, the company failed, and in 2018 Joysen Safety Systems acquired it.
What is the cost of repairing an airbag sensor?
Depending on the automobile model and labor charges, the cost to replace an airbag sensor ranges from $100 to $600. A sensor for an airbag costs between $50 and $300, as does the labor.
Both the airbag sensor and its replacement are delicate parts. Even for an expert, correctly diagnosing and installing the airbag sensor can take up to two hours.
The airbag sensor itself is typically not very expensive; you may anticipate paying between $50 and $300 for a brand-new one. Avoid taking the chance by always purchasing OEM original, genuine products and never aftermarket sensors.
You can save money by replacing the airbag sensor yourself if you are highly confident working on cars and meticulously following the repair manual.
If you have even the least qualms regarding the replacement, have a pro handle it.
Keep in mind that it is a crucial component, therefore installing it properly is important in case of an accident. Additionally, if you make a mistake, there is a chance that all of the airbags in the automobile would deploy, costing thousands of dollars to repair.