Get 2017 Hyundai Tucson headlights and exterior bulbs for your cars, trucks, and SUVs at AutoZone.
In This Article...
How are low beam headlights changed?
- Get some gloves to wear. One of the main reasons for early burn out is oil staining. Your light bulb could burn out very rapidly if there is even one fingerprint on the glass. Wearing latex or vinyl gloves while changing your bulb will help you avoid this.
- Choose the appropriate headlight bulb. You may find out what kind of bulb your car needs by consulting the owner’s manual. You can use it to help you replace the bulb for your particular car.
- Shut off your car. It is for your protection.
- Locate the headlamp holder by opening the hood. It’ll be close to the front of your vehicle.
- Remove the power cables. Three of them will typically need to be disconnected. These are frequently secured by a screw cap, metal clip, or plastic catch.
- Remove the old lightbulb. In many cars, the headlight holder’s back may be taken off to reveal the bulb. To remove the bulb from its socket, you might need to spin it.
- substitute a fresh bulb. Wear your gloves before touching the new bulb, don’t forget. Additionally, using an alcohol wipe to clean it prior to installation is a smart idea. Put the headlight holder back in its original location after inserting the bulb into the base. Reconnect the wires that you previously disconnected.
- Examine the bulb. In order to check that your new bulb is operating properly, turn on your headlights. Check your work again to make sure you used the right bulb if it doesn’t work. If everything appears to be in order, you can also have a wiring or fuse problem. Consult a local mechanic for assistance if you need assistance figuring out what is wrong.
Through OKCarz, motorists searching for used cars for sale in and near Tampa, Orlando, Lakeland, St. Petersburg, and Brandon may quickly locate what they’re seeking for. Drivers can pick from a wide selection of automobiles that we offer. No matter what kind of model you’re looking for, our staff will assist you and your passengers in locating a car that satisfies your needs and preferences on a daily basis.
How are broken low beam headlights fixed?
A fuse, headlamp relay, headlight switch, dimmer switch, or a wiring issue are the most likely culprits. A blown fuse is essentially the only cause that can be easily fixed. Find the headlight circuit’s primary fuse in your owner’s manual, then swap it out with a new fuse with the same amp rating.
What may make low beam headlights malfunction?
The blowing of a fuse If the bulbs themselves weren’t the issue, a blown fuse might have caused their failure. The issue might be resolved by changing the fuse. However, if the fuse blows out once more, the following problem could be to blame for your headlight failure.
What does the phrase “check headlamp low” mean?
Only the bulb in charge of that setting may need to be replaced if a headlight operates on low beam but not high beam or vice versa. Replace the beam selector switch if necessary. If both of your headlights go out simultaneously, look for a broken ground connector, wire, fuse, relay, or switch.
A 9003 bulb has high and low beams, right?
We carry the 9003 bulbs over to the opposite side of the argument. As was already established, the H4 and 9003 bulbs are nearly identical. The two do differ slightly from one another, especially so in the use scenario. As previously implied, the 9003 bulbs entered the picture to replace the H4, which had limitations. Although it has a more controlled output than the other bulb, the 9003 bulb is a double filament variety.
Bypassing these limitations, the 9003 eventually found its way into car headlamps. You can discover that the bulbs are currently being sold under one another’s names. For instance, a dealer would advise choosing the 9003 if you desire an H4 bulb.
To answer your question, the 9003 is primarily utilized in automobile lighting, where it excels by offering sufficient illumination. How do 9003 and 9006 compare? Many individuals might be confused by the two bulb types, probably because of the ‘900’ numbering. Given that the 9003 is a double filament bulb and the 9006 is a single filament low beam bulb, the two are highly dissimilar. The 9003 may be used as both a high beam and a dipped beam bulb thanks to its dual filament. The fact that the bulbs are headlight-bound is one thing they have in common.
Is it challenging to switch headlights?
Even if you have the most expensive wheels, if your headlights aren’t working, it won’t mean much. Thankfully, changing a headlight bulb is a rather simple procedure.
Tools required:
- brand-new light bulb(s) Make sure you purchase the appropriate bulb type for your car.
- alcohol-based tissues and wipes
- tool for Phillips screws
Instead of from the front of the automobile, you’ll access your headlight bulb via the engine compartment. Locate the headlight close to the front of the car by opening the hood. It will be housed in a bulb holder and connected to the bulb by a power connector, which typically has three wires.
Depending on your vehicle, the power cables are connected to a plug at the base of the headlamp and secured by a plastic catch, a metal clip, or a screw cap. Push down on the little lever at the top of the plastic catch as you take the plug out. Hold onto the metal clip as you draw it up and away if you’re dealing with one. When working with a screw cap, turn it counter-clockwise to unscrew it.
Holding onto the base of the old bulb, you should be able to remove the back of the headlight holder after the wires have been severed. In some circumstances, you might need to slightly spin the bulb to release it.
Use tissues or gloves to handle the replacement bulb; you don’t want your skin’s oils to get on it. Before you install it, you should give it a thorough cleaning with an alcohol wipe. When the bulb is prepared, insert it into the plug’s base. No rubber gasket will be seen if it has been placed properly. The headlight holder and power wires can be plugged back in when the bulb has been installed. Make sure to switch on your headlights to test the bulb.
Working with your headlights differs slightly from changing your rear tail lights, which include your brake lights. On some models, you may unscrew the housing that houses the bulb from the outside, while on other models, you have to do so from inside the trunk. To access the bulb after unscrewing the housing, you might need to work with tabs, screws, or tiny knobs on the tail light cover. The electrical wiring won’t need to be taken out, but be careful not to pull the housing out too much lest you rip the wires.
The bulb should be easy to remove by either pulling it out straight (as in most contemporary cars) or by pushing it in while simultaneously unscrewing. Replace the housing and reattach it when the replacement bulb has been installed. Once more, be careful to test the bulb by turning the ignition on and using the brakes.
How do I choose the right headlight bulb?
For information on bulb fittings, you can either get in touch with the company that makes your car or just check your owner’s manual, which should list all the fittings your car needs for each kind of light.
Why do my high beams function but not my low beams?
Modern automobiles, especially Volkswagen models, are amazingly intricate technical feats. Everything in your car’s electrical systems, including the headlights, is protected by at least one fuse. These ingenious tiny electrical components will only let through a specific amount of current. If there is too much power, the fuse will break the connection to safeguard the remaining parts of the electrical line and components. Sometimes fuses blow for no apparent cause, in which case you just need to replace it to fix the issue. Get a factory-trained professional to take a closer look if the fuse blows again.
One of the more frequent causes of low beam headlights not functioning when high beams do is a faulty headlight relay. Essentially an electrical switch, the low and high beams each have their own relay. Relays might fail, just like fuses. The relay is more prone to malfunction since the low beams are utilized far more frequently than the high lights. Similar to fuses, if everything first functions properly before the relay malfunctions once more, you likely have a more significant electrical issue on your hands.
O’Reilly does it change the headlight bulbs?
Simply stop by one of our stores and pick up a pair of headlight bulbs for a relatively simple fix. You can try changing them yourself, or we’ll be pleased to do it for you. Not every location offers all services.
Can I change the headlight bulb on my own?
Without touching the bulb’s glass, carefully screw in the new bulb. If you do, the oil and grime on your hands could cause the bulb to burst once it heats up. Your car’s hood should be closed. Your headlights ought to work perfectly again after installing the new bulb, allowing you to enjoy driving your automobile day or night.
Most of the time, changing a headlight is simple and doesn’t need sending your car to the shop. See what other do-it-yourself auto maintenance tasks are available.
Do Hyundai Santa Fe headlights contain LEDs?
The external design of the 2019 Hyundai Santa Fe can make you fall in love at first sight. There is no questioning the attention to detail in the design, which included numerous aspects into something as basic as the window glass. You’ll also fawn over chic additions like the shark fin roof antenna. To understand more about the external design elements and specifics of the 2019 Hyundai Santa Fe, continue reading below.
How much should a headlight bulb replacement cost?
The majority of fatal auto accidents, according to the National Highway Traffic Safety Administration (NHTSA), take place after dark. It’s crucial to have functioning headlights if you want to keep your family and yourself safe when driving.
Fortunately, repairing your headlights is among the least expensive car repairs you’ll need to make.
A mechanic’s headlight bulb replacement typically costs between $100 and $130. The cost of doing the work yourself will be significantly influenced by the brand, model, and kind of bulb used in your car.
Should I unplug the car’s battery before changing the headlights?
When replacing a blown headlight bulb, always unplug the battery. The electrical system of your car is connected to the headlight bulbs. While the alternator recharges the battery, they will draw power from it. You should always disconnect the battery when working on your car’s electrical system to be safe. The battery doesn’t have to be taken out. Instead, all you have to do is unplug the ground cable (the black cable) until the blown headlight bulb has been replaced.
Will AutoZone change the bulb in my headlight?
On the AutoZone website, I was able to find the replacement for my broken right headlight bulb. I was going to go there tomorrow to buy a new bulb, but I don’t think I can put it in myself, and I’m not sure if I should make an appointment with a mechanic. Does Autozone perform headlight bulb replacements for you?
In less than two minutes, find out if your auto insurance is being overcharged.
AutoZone can assist you in replacing a burned-out headlight bulb, but only if you bought the replacement bulb from their store and only if the procedure doesn’t involve disassembling the car.
While knowledgeable AutoZone staff members can assist you with a straightforward replacement, the store is not a substitute for a qualified mechanic. They won’t take apart or remove any of your car’s parts to service it.
Not all AutoZones will change your headlight for you, to add to that. You shouldn’t rely on your neighborhood AutoZone to assist you service your automobile because different locations may have different policies. Of course, you may always show up and inquire, but just to be on the safe side, you should probably schedule a repair appointment.
Jerry will automatically produce personalised quotations from more than 55+ top name-brand insurance carriers when you download the app and answer a few questions.
From the app, you can shop and compare prices, manage your policy, and even switch policies! Jerry handles everything, including getting in touch with your insurance, buying your new coverage, and dealing with the tedious paperwork.