The battery in your Hyundai key fob is simple to change. A replacement CR 2032 3V battery is all that is required. They typically cost between $3 and $5 for a pack of 5. Wearing latex gloves is advised because you will be contacting a motherboard during this process, which could result in unintended harm.
- Remove the emergency key from the fob’s base.
- Between the release button and the key slot, insert the key.
- Turn the key until the fob pops open as if you were unlocking a door.
- Open the fob while facing the buttons downward (otherwise they will fall out).
- Remove the barrier and motherboard, then set aside the button-side of the fob.
- Remove the dead battery from its mount using the key.
- Place the + side of the new battery in its bracket.
- Replace the fob’s button-half, motherboard, and barrier.
- Set the release button peg in the appropriate hole.
- Reassemble the fob with a snap.
You’re done now! Press any button to put your Hyundai Smart Key to the test. If all was done correctly, a tiny red light should flash over the unlock button.
In This Article...
What kind of battery does a key fob for a 2014 Hyundai Sonata use?
A CR2032 battery powers the majority of Hyundai key fobs. Once you have a new Hyundai key fob replacement battery in your possession, insert it into your key fob exactly where the old one was. Check to see if the battery is in contact with each connection.
How is a Hyundai key fob programmed?
- As soon as you get inside your Hyundai, check that all the doors are closed.
- Put your Hyundai’s ignition in the “ACC” (accessory) position using your key.
- Keep pressing the “open” or “unlock” button on the key fob until the light on your car starts to flash.
- Congratulations
How is my car key fob reset?
- Take hold of all of your car’s remote starters.
- Place your ignition key in and select Accessory (or press the start button once without pushing the brake pedal).
- Your remote car starter’s Lock button should be pressed.
- After turning it on for five seconds, turn the key back to the “off” position (or press the start button again).
- The on-off cycle should be repeated a total of four times.
- You’ll hear a sound (a “ding,” “ping,” or “buzz”) on cycle number four when you choose the Accessory position. Right now, programming mode is active.
- Lock the remote by holding down the button (s).
- Turn off the car in ten seconds.
- Shut the door, exit the vehicle, and then try the remote.
- If so, that’s excellent!
- It’s time to call the dealership if it doesn’t.
Why won’t my key fob function when I change the battery?
A dead battery is the most frequent cause of a key fob not functioning. Having said that, your keyfob might be having more serious issues. You might require a key fob replacement or perhaps auto door lock repair if your key fob stops operating after a battery change.
If I change the battery, do I need to reprogram my key fob?
After changing the battery, you typically do not need to reconfigure the key fob. However, you might need to reprogramme it by re-pairing it with your vehicle if you’ve replaced not only the batteries but also some of the internal cabling and electronics.
How much does a new Hyundai key fob cost?
It’s more likely that you will be allowed to utilize an aftermarket key fob if your automobile is at least ten years old, according to CR’s Ibbotson. Many of these less sophisticated fobs can be configured by the consumer, a local technician, or an automotive locksmith.
Ibbotson advises making sure to phone your neighborhood garage first to confirm that they can do the task, as key-fob programming equipment levels can vary from shop to shop. For instance, a Maryland-based repair shop called Murray’s Auto Clinics informed CR that they are unable to program key fobs for any vehicle with push-button start or keyless entry.
We took our vehicle to M.J. Sullivan Hyundai in New London, Connecticut, where we were charged $120 for programming (one hour of labor), which is what they would have charged us if we had purchased the key fob from them.
Hyundai sent us a laser-cut mechanical backup key for $72.47, bringing the total cost to $272.42 (the car waited at the shop for two days); if we had ordered the key fob through the store, the total would have been $428.92).
For some makes and models, you can purchase a cheap aftermarket fob and program it yourself if your home unexpectedly gains a third driver, such as a teenager.
We purchased a fob from BestKeys from Amazon for CR’s 2008 Chrysler Town & Country minivan. Although it lacks the Chrysler branding on the back, it resembles the two original fobs that came with the minivan when it was new. The uncut mechanical key and internal circuitry were both included in the $14.30 price. (However, we didn’t see the need to shell out the cash to have a locksmith cut that third key.)
Chrysler customers can program a third key fob themselves if they already have two functional ones, just like GM owners can. The owner’s manual contains clear and straightforward programming instructions.
What does the Hyundai key fob’s hold button do?
What does auto hold accomplish? It prevents your automobile from rolling away accidently when it is moving or stopped, thanks to the ABS/ESC hydraulic unit.
Where is the Hyundai Sonata’s smart key holder located?
This information caught my attention. I think it would also benefit our Palisades!
Fix 1: While tapping the brake, push the Start button using the rear or end of the dead key fob. Fix 2: Place the dead key fob, buttons facing up, in the Smart Key slot (located in the locations specified below), and depress the brake while pressing the Start button.
Slots for Smart Keys: There are three places where these slots can be found: 1. on the front of the center console; 2. behind a panel right below the infotainment control knob; or 3. on the left side of the glovebox when it is open.
What occurs when the battery in your key fob runs low?
The transmitter’s range decreases as the fob battery gets weaker. This implies that for the key fob to operate, you must be close to the vehicle. When a smart key fob is in your pocket or handbag for automobiles with push-button starts, the car might not always detect it if the battery is low.
Why doesn’t my automobile recognize my key fob?
Key fob battery failure The most frequent cause of a keyless entry system failing to send signals is a faulty battery in the key fob. Use the extra key fob to unlock the car and turn on the ignition if one is available. Use the key that is included in the spare fob if it is not available to unlock the door.
Key fobs: Do they have batteries?
The past ten years have seen a significant development in key fobs. Push start systems of today are an evolution of what was once only a convenient technique to remotely lock and unlock doors. Despite the fact that key fob technology is continually evolving, their power source has not changed. Batteries power key fobs and other auto remote controls. That implies that the battery inside them needs to be changed when it runs out of juice. Batteries Plus can assist if your key fob isn’t working as well as it once did. For answers to all of your questions about automobile remotes, including what kind of batteries they need, how long they last, and where to buy a replacement battery, continue reading.
Can a key fob be programmed without visiting the dealership?
Can a key fob be programmed without visiting the dealership? Yes, you can program the key fob’s locking and unlocking features without visiting the dealership. However, you might need to visit the dealership or a locksmith if you need to program the transponder in order to be able to start the car with the key.
How long do the batteries in key fobs last?
Keyless entry is a fantastic feature, but you can only benefit from it if you keep the technology up to date.
The little things in life can often mean the most, such as not having to search through your purse for your keys or using your key fob to raise and unlock the back doors so you can load groceries.
But what occurs if the fob breaks down? The key fobs for your car require maintenance just like the vehicle itself does.
When anything breaks down, Gary Freeman, owner of C & G Auto in Myrtle Beach, advised against replacing it right away.
“A replacement fob can be pricey; they can cost several hundred dollars, and once you have a replacement fob, they need to be programmed,” said Freeman.
He advises checking the battery as your first action. If you have to press the lock or unlock button on the remote numerous times before it locks or unlocks, it could be a sign that the battery is starting to lose power, according to Freeman.
According to his calculations, the keyless entry remote can be safely stored or hung up anywhere beyond the six to ten feet from which the automobile computer system can read the fob.
According to Freeman, the battery life for the majority of automotive key fobs is three to four years with regular use. Additionally, he claims that the battery life of your fob may be impacted by where you keep it. Freeman advises against hanging the fob near the car or leaving it in the car overnight.
“It (the key fob) does send a signal continuously, so it drains the battery in the key fob and its causing an excessive drainage on the battery of the automobile,” noted Freeman. “A computer is identifying that signal saying I’m ready to start.”
According to Freeman, if the key fob malfunctions, the automobile frequently won’t start because the computer system won’t acknowledge that the key fob is present in the vehicle.
“In most situations, the owners’ manual will clear that up for you, or practically any auto repair facility can replace that battery,” Freeman continued.