The satisfaction of repairing a car on your own is something. You might be able to perform a variety of things that you would typically allow a professional to handle if you learn some fundamental information about your car and put it to use. Changing a tire on your Hyundai Elantra is one of those duties. Simple basic tools that you keep in your trunk all the time are all you need to change an Elantra tire. Anywhere you are, you will be able to change a tire on your Hyundai Elantra if you carefully and correctly follow the instructions.
Prepare the vehicle and the tire-changing equipment. Place your automobile in a level spot away from traffic, engage the emergency brake, and drive away. Make sure the ignition is off as well so that the engine is off. Get the tools close to the tire and look for them in your trunk.
Use the lug nut wrench to spin the lug nuts counterclockwise on the tire you’re changing, but do not remove them.
Place the jack underneath your automobile, close to the tire, between the wheel wells. Look beneath the vehicle close to the wheel well of the tire you’re replacing to locate the spot where the jack should be placed. It may be a smooth surface on the frame iron, a dimple, a notch, or a pinch in the steel. Then, use the jack to raise the vehicle just a little bit. Make sure the car is securely seated on the jack. Lift it up at least three inches off the ground so the flat tire is visible.
After loosening each lug nut in Step 3, take off the tire. Keep the nuts in a secure location because you’ll need them soon.
With the spare tire mounted, attach the lug nuts to the studs and tighten them with your hands.
Once the automobile is securely on the ground, slowly lower the jack. Using the lug wrench, tighten each lug nut.
In This Article...
How is a tire changed?
- Locate a Secure Overpass to Pull Over.
- Inspect the materials.
- Take off the lug nuts.
- Your car should be raised off the ground.
- Remove the Tire and the Lug Nuts.
- Fix the spare tire to the vehicle.
- Switch out the lug nuts.
- As you squat down, start tightening.
Is there a spare tire on a Hyundai Elantra?
Unfortunately, unlike its cousin, the Hyundai Kona, the 2021 Elantra lacks a spare tire. In the last five years or so, automakers have been more focused on increasing fuel efficiency, which has caused them to discontinue providing spare tires for automobiles.
How is a front tire changed?
- Get the automobile ready. Put the handbrake on and get everyone out of the car.
- Set the wheel chocks in place. The car is kept from rolling while being jacked up by chocks.
- Wheel nuts should be loosen.
- Car jacked up.
- Get rid of the flat tire.
- Install the spare tire.
- Tighten the bolts after lowering the automobile.
- Car is fully lowered
How difficult is it to replace a tire?
Actually, changing a tire requires quite a bit of physical effort. The lug nuts must be removed, the jack must be turned, and then the tire must be raised by bending over. People frequently attempt to complete all of this in a rush to get moving, but it is a mistake.
Does changing a tire require the car to be in neutral?
It’s crucial to remember to leave the vehicle in the proper gear when changing a tire on a manual transmission vehicle. Naturally, you should turn off the engine before beginning the tire change. However, you should leave the gearstick in either first or reverse.
The handbrake only works on two wheels, often the rear wheels, which is why you want to do this. With the engine turned off, shifting into first or reverse causes the front wheels, which are typically the driven wheels, to lock.
If your vehicle has an automatic transmission, you may leave it in the “Park” or “P” position.
How much time does it require to change a tire on your own?
Have you experienced a tire puncture while traveling? Perhaps you’ve seen warning signals of low tire wear and are concerned about your safety while driving. Or perhaps you haven’t replaced your tires in a while and decide it’s time to do so.
The first question that comes to mind, regardless of the situation, is “How can I replace a tire, and how long does it take to change a tire?”
The circumstances will determine how long it takes to change a tire:
- A professional tire change takes 5 to 15 minutes.
- 45 minutes to 5 hours are needed to change a tire at an auto repair shop.
- Less than an hour to change a tire with the aid of roadside assistance.
- An independent tire change takes 15 to 30 minutes.
Typically, it takes 15 minutes to replace a tire. However, it may change according on the circumstance, the type of car, and the worker.
We’ll let you know how long changing a tire on your own, at a tire shop, and with roadside assistance will take.
Can I replace a tire using only a jack?
Yes, changing a tire probably only requires one jack stand, but it’s not ideal to repeatedly flex the frame in that way, especially on a unibody car. The home mechanic can change tires and safely raise a vehicle from either the side or the end by using two jack stands.
To change a tire, do you need a jack?
One of the primary responsibilities of car ownership is being prepared. Always keep emergency supplies in your car just in case. A car jack is the best tool for changing a flat tire since it makes it simple to pull the tire up and away. But according to It Still Runs, there are some things you’ll need to complete the task if a jack is not available:
Gloves, a torch, blankets, towels, and rags, as well as a tire ramp, are additional useful items. Additionally helpful are lubrication (light machine oil), a tire pressure gauge, and roadside safety supplies like flares and reflectors.
Why won’t my front tire blow off?
Why Does a Wheel Get Stuck? It usually just comes down to corrosion buildup from the wheel being in place for a long time. A coating of glue-like corrosion can form between the wheel and the hub’s mounting surface, which can firmly fasten the wheel to the hub.
How much time can you spend using a spare tire?
You can drive to the closest repair facility with the spare tire in order to have the flat tire evaluated and either repaired or replaced. With a donut-shaped spare tire, you should not travel faster than 50 mph or farther than 50 miles. Long-distance driving with a spare tire could potentially harm the transmission and other components of the car.
Should lug nuts be loosened before jacking up the car?
- security first. Maintain a safe distance from oncoming traffic, put your car in park, engage the parking brake, and turn on your warning lights. It is preferable to ask for roadside help if you are unsure that you can avoid danger.
- Consult the owner’s manual. It should have directions for changing tires, including where the jacking point is.
- Bring out your spares and tools. Typically, they are kept in a compartment in the trunk. The jack should provide usage instructions as well.
- Make sure the jack is set up correctly. Ensure it is positioned correctly in the vehicle’s jacking point and is facing the right direction.
- Before jacking, loosen lug nuts by roughly a quarter turn.
- The car should be jacked up high enough so that the tire is off the ground.
- The lug nuts should be taken off and placed so they won’t roll away.
- Pull the flat tire off and place it behind the jack underneath your car, or if it’s too broad, try another position under the car. This is crucial in the event that the car slips off the jack.
- Make sure the valve stem is facing you as you install the spare.
- Hand-tighten the lug nuts while reinstalling them.
- Once the tire is in touch with the ground and partially loaded, lower the jack.
- To ensure that the wheel is properly installed, tighten the lug nuts in a star pattern rather than a circle pattern. This ensures that the wheel is not out of alignment and won’t pop back into place while you are driving, perhaps loosening other bolts and causing wobbling or even worse—the nuts breaking and the wheel coming off.
- The car should now be lowered all the way. You’re prepared to make a cautious trip to the nearest tire shop to get your regular tire changed or repaired.
Spares should only be driven for brief distances and at low speeds. Your spare tire’s speed rating can be lower than that of your primary tires. Have a tire specialist inspect your spare at the shop so that it is in working order for the next time you need it.
What kind of tool are lug nuts removed with?
While lug nuts can be loosened and tightened with a lug wrench, removing several tires quickly and efficiently with a 1/2-in. cordless impact wrench. An outstanding option is the Milwaukee 2767 18-Volt 1/2-in. Impact Wrench.
It has a friction ring that prevents sockets from slipping off the anvil while allowing for quick socket changes, and it is well-balanced and only 8-1/2 inches long. With its 1,400 foot pounds of bolt-busting power, this tool can remove lug nuts that are severely corroded or overtightened in a flash.
Be aware that torque limiting sticks are required if you’re using an impact wrench. Check out the Neiko 02453A 1/2-in. eight piece set. Drive with the torque limiter set, particularly if you’re changing the tires on many vehicles.
Six-point sockets with deep, thin walls are coated to protect finished lug nuts and wheels. For easy identification, the extensions and sockets are color labeled. You can throw this set, along with your impact wrench, into the back of your car before a road trip because it is housed in a handy blow-molded storage container.
How do you turn a bolt out of the way?
One important fastener detail that many DIYers either overlook or are too frightened to inquire about is this one.
As seen in the illustration below, the majority of common screws, bolts, and nuts are unscrewed by rotating them counterclockwise.
Righty tighty, lefty loosey is a saying that all junior mechanics are taught, and trying to commit it to memory is a good approach to remember this.
But keep in mind that there are exceptions to every rule. Some fasteners have left-handed threads, for instance, requiring that the object being secured be turned in the opposite direction. The rule is flipped in situations like this, so always take a moment to double-check if you run into a particularly stubborn nut or screw to avoid damaging the fastener or bursting a blood vessel!
Where can I use a jack to lift my car?
In order to safely lift the car, most automobiles have strengthened metal ribs that serve as the jacking points. There are typically four jacking points on each car. They are situated beneath the car’s rocker panels, close to the front wheels, and close to the back wheels.