In This Article...
The Key Programming Approach
- Lock the vehicle.
- After getting inside, lock all of the doors.
- Activate position I of the key. Only some of the instrument cluster lights will illuminate. Within five seconds, take the ignition key out.
- Hold the unlock button pushed on the keyfob remote control.
- Press the lock button three times while keeping the unlock button depressed. Pull back on each button. It has a programmable key.
- Repeat steps 4 and 5 for any additional keys you may have. Never put the extra keys back in the ignition.
- Check to verify if the remote is capable of opening and closing the doors.
- To complete, turn the key to the “ignition” position.
Adding a remote door lock/unlock function to your BMW key
Follow the steps below to enable or disable the remote function of a replacement BMW key:
- Close and lock all of the doors while using every remote in the vehicle.
- Using the new master key, turn the ignition to the “run” position.
- without opening any doors, remove the key
- On the new master key, hold down the UNLOCK button (the arrow button).
- Press the key LOCK button (the BMW logo) three times quickly while maintaining pressure on the unlock button. Press the buttons swiftly but slowly, pausing for only one second in between each BMW logo press.
- On the final button press, simultaneously release both buttons.
- To verify the initialization of the remote feature, doors will lock and unlock. To enable all keys on the remote door lock system, use the same button press programming method for each key within 30 seconds (up to 4 remote keys).
Follow the steps above with all of your keys except the one you want to remove if you have lost a key or would otherwise like to disable the remote function of one of your keys. This procedure will remove the outdated or lost door remote from the list of door remotes that are currently in use, rendering the lost key useless for remote vehicle unlocking.
Any remote key that isn’t programmed in the same session won’t be able to lock, unlock, or disarm (FZV & DWA) the car, but it will still work to start it (EWS).
How is a 2008 BMW key fob programmed?
How to Set Up a New BMW Key Fob Press the BMW logo three times while holding down the unlock button, and then let go. Within 30 seconds after the initial key programming, repeat step three if you still have more keys you’d like to program. To finish the procedure, start the engine.
How can I learn my BMW key again?
Turn the ignition of the automobile five times fast to position 1 and back. Remove the ignition key from the car. Press the BMW logo three times while holding down the unlock button, and then let go of the button. Within 30 seconds of the initial key programming, repeat step 3 if you want to program any additional keys.
What does the BMW key’s diamond button do?
Does anyone have any knowledge of what the key fob’s diamond button is meant to do?
The included manual is incredibly succinct. It refers to a “Headlight courtesy delay feature,” although it’s not entirely clear what this feature performs. “If the standby state is switched on and the high-beam headlights are enabled, the low-beam headlights remain on for an of time,” the text states. Even if “… for a period of time” is meant to be “… for a length of time,” that still doesn’t adequately describe what this feature is.
According to the description, it can only be used when the automobile has just been turned off and the high beams are on. However, when the car is locked, the button appears to have some effect. The inside lights occasionally come on. The headlights occasionally come on. It is quite unpredictable and challenging to duplicate.
What experiences do others have? Has anyone figured out what this button’s actual purpose is?
It is unfortunate that it cannot be set to perform things like open the windows or sunroof, switch on the heating, or other things!
Mine has two options (330e in Belgium): turn on the lights in the house or turn on the air conditioning. In the options for the car, I can select the default function.
It briefly illuminates the headlights in my automobile. Excellent for illuminating the path to your front entrance or finding your car at night in a big parking lot.
Check the “Home lights” setting under “Exterior Light Settings” on your iDrive to make sure it is not set to 0 seconds.
My headlights now turn on for 10 seconds when I hold the diamond button on the key because I set mine to that duration (G20 330i).
Why won’t my BMW key turn?
You’ll need a CR2032 battery if your key fob is functioning well but your BMW key fob battery has to be changed. Make sure you’re using the appropriate size of these tiny cells, sometimes referred to as “watch batteries.”
I need to connect my BMW key fob again.
While keeping the unlock button depressed, press the BMW logo three times on your BMW key fob. After pressing the BMW logo three times, release the unlock button. Once the ignition is turned on, your new key should be associated with your BMW.
How do I start my BMW remotely?
You can activate Remote Engine Start by pointing your BMW key fob at your car and pressing the lock button (the BMW Roundel) three times in a row.
How is a replacement key fob programmed?
- STEP 1: Start the engine. All doors should be closed, and you should be seated in the driver’s seat with the key fob and the ignition key.
- Press the lock button in step two.
- Turn off the ignition in step three.
- STEP 4: Repeat Step 3 with more key fobs.
- STEP 5-Start the procedure over.
Without the original, how can a key fob be programmed?
After locking every door, turn the ignition off. Set the accessory or “ACC” position on the ignition key. The door locks will cycle once once you turn the ignition key off once more. To program the key fob, press any button three times straight.
Can I set up a key fob on my own?
Yes, a replacement automobile key can be obtained without the original. Since people frequently misplace their car keys, replacing a misplaced car key is an easy operation. Nevertheless, depending on the key type, it could be pricey.
A key fob is a little electronic gadget that you can use to remotely lock and unlock your car. Other capabilities of the fob could include a remote engine starter, a trunk opening, or a proximity system that allows you to open your car without taking the fob out of your pocket.
Depending on how sophisticated the key technology is, replacing car keys can be expensive. An old metal key can be duplicated for less than $10 at a hardware store. On the other hand, the most recent smart keys must be ordered from a dealer and might cost between $200 and $500.
Your car key’s battery can be changed easily by opening it up, identifying the battery type, and going to the store. If you’re unsure of how to open the remote, it pays to consult your owner’s manual because you don’t want to force anything open and break it.
Today’s automobile keys are more secure and capable thanks to technology, but the gain isn’t free. The majority of modern keys feature complex electronic parts that must be configured before usage.
You may be able to buy an after-market key fob via a locksmith or online if your automobile is more than five years old. These sorts of fobs range in quality, but they are less expensive than other options.
You might be able to program a replacement yourself, depending on the make and type of your vehicle. The steps for programming a key fob yourself can differ: Owner’s manuals from certain automakers include instructions. In many circumstances, information can be available online. The catch is that in order to complete the process quickly or at all, you might need two functional key fobs.
It’s wise to acquire and program a backup remote before you require it. Additionally, a lot of used-car buyers (particularly auto dealers) will pay more for a vehicle with at least two functional key fobs or sets of keys.
A misplaced automobile key can indeed be replaced by a locksmith. If you have the option of receiving your replacement key from a locksmith or the dealership, the latter may be less expensive. Before making a choice, be sure to inquire about prices with your nearby vehicle dealership.
Can a key fob be programmed without visiting the dealership?
Can a key fob be programmed without visiting the dealership? Yes, you can program the key fob’s locking and unlocking features without visiting the dealership. However, you might need to visit the dealership or a locksmith if you need to program the transponder in order to be able to start the car with the key.
The cost of a BMW key fob
The price of a 2020 Toyota Sienna fob was comparable. Dealers, however, gave prices as low as $150 to replace a key fob for a 2017 Honda Accord. A number of BMW retailers claimed that the additional security features built into the 2020 X5 key fob justifies the roughly $500 they spend to replace and program one.
What is the price of a BMW display key?
We had the chance to experiment with BMW’s newest keyfob at the media debut of the 2016 BMW 7 Series. The touch-sensitive key, also known as the BMW Display Key, is an optional accessory for the new 7 Series and is just $250 in the United States. The key has four buttons on the front for lock, unlock, trunk release, and panic for that small price—which is less expensive than many other BMW keyfob replacements.
The key has a full color touchscreen in the middle that allows you to swipe through various features, such as door locking status, toggle lighting, fuel range, and climate control scheduling. Although the U.S. regulatory bodies have not yet approved it, the BMW Digital Key can be used to self-park your 7 Series in Europe.
According to BMW, the key’s battery lasts for around a week and can be wirelessly recharged in the armrest of the vehicle. Even if the touchscreen is broken, you can still open the car with the key.
It’s incredible what BMW has accomplished with something we always considered to be a simple tool, and we anticipate that keyfobs of the next generation will become much smarter.
Why won’t my BMW key fob function now that the battery has been changed?
A dead battery is the most frequent cause of a key fob not functioning. Having said that, your keyfob might be having more serious issues. You might require a key fob replacement or perhaps auto door lock repair if your key fob stops operating after a battery change.
How much does it cost to program a key fob?
The typical person who programs key fobs is a locksmith. Typically, key fob programming costs between $85 and $400. Nowadays, most cars come standard with key fobs, often known as remote fobs.
What does the play button for a diamond look like?
a prize given to networks with at least 10 million subscribers. It is comprised of silver-plated metal with a sizable triangle-shaped piece of colorless crystal put into the center. The award was presented during VidCon 2015, and 35 channels were eligible. There are 984 channels with 10 million or more subscribers as of June 28, 2022.