When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car and let it run for 20 minutes to let the sensor reset. Under the steering wheel is typically where you’ll find the reset button for the tire pressure monitor. If you still can’t find it, look in the owner’s manual of your car.
In This Article...
Why do the tires on my Nissan mention maintenance?
The Maintenance Tire Light: What Does It Mean? When your Nissan’s tire maintenance light comes on, it’s time to rotate the tires as part of your normal maintenance program.
Nissan, where is the TPMS reset button?
There is a TPMS reset button, which you can press. The specific placement is specified in your owner’s manual, however it is typically found underneath the steering wheel. By turning your keys to the “on” position while keeping your engine off, you can operate this. Hold the button down until three flashes of the TPMS light appear.
Why are my tires fine but my TPMS light is on?
It’s likely that one or more of your tires have low air pressure if you see the tire pressure indicator turn on. However, even if your tires are in good condition, there are a number of things that could cause the sensors to go off, so you shouldn’t rely only on the data from the tire pressure monitoring system of your car.
We’ve talked about some additional aspects of automobile maintenance in this piece. Read these articles if you have some time:
On a Nissan Sentra, where is the TPMS button located?
Depending on the year of manufacturing, you can find the TPMS reset button under the left side of the dashboard or under the steering wheel. Please follow the detailed procedures below to perform a reset.
How To Reset the TPMS on a Nissan Sentra 2007-2019?
Follow these simple instructions to reset the tire pressure monitoring light if your Nissan Sentra was manufactured between 2007 and 2019:
- Make sure the car is stopped and the engine is off.
- Make that the tire pressure is set properly in each tire. Make careful to verify the tire pressure in the manual or on the door panel.
- It is advised that you drive the vehicle to calibrate the monitoring system at a speed between 16 and 25 mph when this is finished.
Congratulations if you find that this works. If not, you must undertake the following instructions at your own risk or with the help of an auto expert, who may charge a fee.
- Verify that the tire pressure is at the proper PSI.
- Finding the TPMS interface plug is the next step. This can be found in your car under the dashboard. The OBD II wire loom should be connected to the white female plug. You might need to cut the plug off if it is taped in place.
- You must insert a paper clip or wire into the interface once you have located the right plug.
- Make sure to not start your engine after turning on the ignition.
- You must tap the ground six times with the paper clip or any other metal you used.
- Your management light will begin to blink if the connections mentioned above are secure.
- You need to understand that the light is blinking slowly. You may need to check the plug’s connection and repeat the following steps if it is flashing rapidly.
- Once you are certain that the light is flashing slowly, you should resume driving the vehicle between the speeds of 16 and 25 mph. By doing so, the internal computer’s calibration and adjustment will begin.
- Only if your tires have low pressure will the light turn back on. Check the condition of your tires and reflate them according to the recommended specifications.
My TPMS light won’t turn off; why?
Try the following if your TPMS light is still on after you have inflated your tires to the recommended pressure: 10 minutes at a speed of 50 mph would be plenty. When you start the car again, the TPMS light ought to be off because this ought to reset the tire sensors.
How much does resetting a TPMS cost?
On most automobiles, the service kit ranges from $5 to $10 per wheel. To examine and reset the sensor system, you also need a special TPMS tool and more time. Depending on the type of car, pressure sensors can be replaced for between $50 and $250 each.