The access panel within your wheel housing must be removed by turning inward and outward. A penny can be used to assist in opening the access panel’s shutter. Remove the panel by turning the boh holding clips.
Before removing the bulb’s holding clip, remove the back plug. Carefully rotate the bulb to remove it.
Install the replacement bulb in the same manner that you did the original. Plug the back out. Reinstall the access panel.
In This Article...
How much does a BMW 328i headlight bulb cost?
Replacement Headlight Bulb Cost Estimate for a BMW 328i. Replacement headlight bulbs for a BMW 328i typically cost between $193 and $329. Between $57 and $72 is the expected cost of labor, while between $136 and $258 is the projected cost of parts.
How much does a BMW headlight replacement cost?
Your cost to repair a BMW headlight can easily range from $100 to $2000 depending on the model of your car, the type of kit, and the quality of the bulb.
What is the turnaround time for a BMW headlight replacement?
- Pick a spot with sufficient lighting in your garage or a tidy portion of your driveway to work on your car. Be calm and give yourself plenty of time (at least two hours) to change a headlight. It can be straightforward, but it also might turn out to be trickier than you anticipated.
- Any fasteners and retaining clips you’ve taken off should go in a container or jar. Otherwise, they’d be too simple to lose.
- Mark the location of the wiring removal with masking tape and a felt-tip pen to ensure that it is reinstalled accurately.
- Kneeling or working beneath the car can be made more comfortable by using an old throw rug, a rubber mat, or a sizable piece of clean cardboard to lie on.
- When connections are made, keep an eye out for a loud click.
We anticipate that your headlight replacement efforts will succeed if you follow these advice. We also hope that you don’t need to replace as many bulbs as this guy:
OpenWeb was used to import this content. At their website, you might be able to discover the same material in a different format or more details.
How is a headlight assembly changed?
- First, take out the outdated headlamp assembly.
- Disconnect the assembly in step two.
- To remove the headlamp retaining ring from the headlamp, turn it counterclockwise.
- Step 3: Cut off the electricity.
- 4. Remove the previous assembly.
- Replace the assembly in step five.
- Connect the new assembly in step six.
How can I tell whether the headlights on my BMW are HIDs?
The colors of the beam pattern typically vary depending on the choice. Go ahead, turn on your headlights, approach a garage door, and take a look. Look at the beam pattern; if it’s yellow, it probably has a halogen bulb as its typical power source.
When you turn on your headlights, if they flash briefly, they are likely HID if they continue to flash for a prolonged period of time (about seven to ten seconds at peak performance and usually in a white color). When you turn on your headlights, they usually have factory LED if they instantly come on with a nice, white light.
Can you easily replace your own headlight?
Even if you have the most expensive wheels, if your headlights aren’t working, it won’t mean much (and as we know from numerous movies and cop shows, a burned-out light will lead to an unwelcome stop by a highway patrol car). Thankfully, changing a headlight bulb is a rather simple procedure.
Tools required:
- brand-new light bulb(s) Make sure you purchase the appropriate bulb type for your car (your local auto parts store should be able to match a bulb with your make and model)
- alcohol-based tissues and wipes (to clean and hold the new bulb)
- tool for Phillips screws
Instead of from the front of the automobile, you’ll access your headlight bulb via the engine compartment. Locate the headlight close to the front of the car by opening the hood. It will be housed in a bulb holder and connected to the bulb by a power connector, which typically has three wires.
Depending on your vehicle, the power cables are connected to a plug at the base of the headlamp and secured by a plastic catch, a metal clip, or a screw cap. Push down on the little lever at the top of the plastic catch as you take the plug out. Hold onto the metal clip as you draw it up and away if you’re dealing with one. When working with a screw cap, turn it counter-clockwise to unscrew it.
Holding onto the base of the old bulb, you should be able to remove the back of the headlight holder after the wires have been severed. In some circumstances, you might need to slightly spin the bulb to release it.
Use tissues or gloves to handle the replacement bulb; you don’t want your skin’s oils to get on it. Before you install it, you should give it a thorough cleaning with an alcohol wipe. When the bulb is prepared, insert it into the plug’s base. No rubber gasket will be seen if it has been placed properly. The headlight holder and power wires can be plugged back in when the bulb has been installed. Make sure to switch on your headlights to test the bulb.
Working with your headlights differs slightly from changing your rear tail lights, which include your brake lights. On some models, you may unscrew the housing that houses the bulb from the outside, while on other models, you have to do so from inside the trunk. To access the bulb after unscrewing the housing, you might need to work with tabs, screws, or tiny knobs on the tail light cover (make sure not to lose the screws if you need to remove them). The electrical wiring won’t need to be taken out, but be careful not to pull the housing out too much lest you rip the wires.
The bulb should be easy to remove by either pulling it out straight (as in most contemporary cars) or by pushing it in while simultaneously unscrewing. Replace the housing and reattach it when the replacement bulb has been installed (screws, tabs, knobs, etc.). Once more, be careful to test the bulb by turning the ignition on and using the brakes.
How is a BMW low beam bulb removed?
Your vehicle needs to be jacked up first. Behind the front wheel, feel under the automobile. The jack point will be underneath the automobile, beneath the leading edge of the door. Underneath this point, slide the jack.
Use a 17mm socket to break the wheel bolts loose before lifting the car. The wheels and nuts can then be removed by lifting the car. There is a detachable panel in the fender well in front of the wheel. Press the panel’s two tabs downward to release it.
The headlight access cover is located behind the panel. Rotate the housing cover counterclockwise while holding it to take it off. By pressing down on the tab above the bulb’s plug with a flathead screwdriver, you can remove the bulb while the headlight harness is still attached.
Remove the bulb and harness from the housing of the headlight. After that, remove the bulb’s plug and discard the old one. Plug the fresh bulb into the headlight harness after removing it from its packing. As installing the bulb, avoid touching the glass because your hand’s oils could cause the bulb to crack when it heats up.
Reinstall the housing cover and the fender well cover after installing the new bulb in the headlight. Refit the wheel to the vehicle next. To tighten and torque the nuts to 140Nm, or 103 ft-lbs, use a 17mm wheel socket.
Authored by:
owner of a 1973 Porsche 914 and a 1998 Impreza 2.5RS with a flat-six engine swap. only when opposing perspectives are horizontal.
I have dampness in my BMW headlights; how do I solve it?
Condensation will evaporate when the automobile is being driven and the headlights are on. BMW views it as normal, but ymmv at your neighborhood dealer. Condensation will evaporate when the automobile is being driven and the headlights are on. BMW views it as normal, but ymmv at your neighborhood dealer.
My headlamp will be changed by Oreillys.
While you wait, at no additional cost to you, our parts specialists can swiftly and easily change wiper blades because they are experts at changing headlamp and taillight bulbs.
Can I change the headlight bulb on my own?
Without touching the bulb’s glass, carefully screw in the new bulb. If you do, the oil and grime on your hands could cause the bulb to burst once it heats up. Your car’s hood should be closed. Your headlights ought to work perfectly again after installing the new bulb, allowing you to enjoy driving your automobile day or night.
Most of the time, changing a headlight is simple and doesn’t need sending your car to the shop. See what other do-it-yourself auto maintenance tasks are available.
How much time is required to replace a headlight assembly?
It is important for you to be patient and give yourself plenty of time (two hours minimum) for changing a headlight rather than pushing yourself to break a new time record when replacing the headlight on your automobile, whether you are merely replacing the headlight bulb or full headlight housing. This is advised, especially if serving people in line isn’t your line of work.
Although replacing a headlight might appear straightforward, it might end up being trickier than you anticipated. Reinstall each component you took out throughout the process, and be sure to place any retention clips and fasteners you removed in a container. Additionally, to protect your car’s headlight lenses from recurrent oxidation, restore the headlight lenses using a headlight restoration kit following a successful lamp replacement.
Why do BMW headlights cost so much?
As a result of having powerful xenon headlights, BMW headlight replacement costs might be considerable. Most premium cars today use xenon or HID headlights, which have been around for more than 15 years. If you’re replacing the bulbs as well, an assembly without a bulb costs around $2,000 plus an additional $500 for the pair. Despite the fact that HID headlights can last almost as long as the car, they are more expensive. Also keep in mind that labor expenditures are not included in that.
How much does a brand-new headlight assembly cost?
How you complete the work will affect your labor costs. often refers to the installation’s overall cost. The typical cost could range from $75 to $400 if you replace the full headlight assembly yourself. If you take it to a car repair shop, the headlight assembly replacement cost will be between $250 and $1,000. Most aftermarket auto parts stores estimate that the cost to replace a single high-intensity discharge bulb can be $100 or more, while the price to replace a whole headlight assembly ranges from $250 to $700. Depending on the type of headlight bulb you select for your car, the cost to replace a headlight unit might range from $15 to $200.
Do I have to unplug the battery before changing the headlight bulb?
When replacing a blown headlight bulb, always unplug the battery. The electrical system of your car is connected to the headlight bulbs. While the alternator recharges the battery, they will draw power from it. You should always disconnect the battery when working on your car’s electrical system to be safe. The battery doesn’t have to be taken out. Instead, all you have to do is unplug the ground cable (the black cable) until the blown headlight bulb has been replaced.
Headlight bulb replacement at AutoZone?
On the AutoZone website, I was able to find the replacement for my broken right headlight bulb. I was going to go there tomorrow to buy a new bulb, but I don’t think I can put it in myself, and I’m not sure if I should make an appointment with a mechanic. Does Autozone perform headlight bulb replacements for you?
In less than two minutes, find out if your auto insurance is being overcharged.
AutoZone can assist you in replacing a burned-out headlight bulb, but only if you bought the replacement bulb from their store and only if the procedure doesn’t involve disassembling the car.
While knowledgeable AutoZone staff members can assist you with a straightforward replacement, the store is not a substitute for a qualified mechanic. They won’t take apart or remove any of your car’s parts to service it.
Not all AutoZones will change your headlight for you, to add to that. You shouldn’t rely on your neighborhood AutoZone to assist you service your automobile because different locations may have different policies. Of course, you may always show up and inquire, but just to be on the safe side, you should probably schedule a repair appointment.
Jerry will automatically produce personalised quotations from more than 55+ top name-brand insurance carriers when you download the app and answer a few questions.
From the app, you can shop and compare prices, manage your policy, and even switch policies! Jerry handles everything, including getting in touch with your insurance, buying your new coverage, and dealing with the tedious paperwork.