- Locate the reservoir of the coolant and clean it.
- Check Level – Ascertain the level of the coolant.
- Determine the type of coolant to use and add the correct amount of fluid.
- Replace the cap on the coolant reservoir and tighten it.
In This Article...
Procedure
- Hood is open. The hood release on your BMW 3-Series can be found underneath the dashboard. When you hear the BMW hood pop open, pull the lever. The hood safety latch at the front of your 3-Series needs to be released next.
- The hood should be raised and locked open.
- the Coolant Reservoir’s location. The BMW’s coolant reservoir (tank) can then be found. Here, you may check the coolant level and top it out if necessary. The coolant expansion tank is found on the driver’s side of the engine in a 3-Series. Slowly remove the cover. Only after the engine has cooled should you open the cap.
- Remove cap to check the coolant level in a BMW 3-Series. Observe the low and high levels in the coolant reservoir tank. You must replenish coolant if the level falls below the minimal level, or your 3-Series risked overheating. The floating gadget is used by the BMW 3-series to gauge the coolant level.
- Add antifreeze and engine coolant. Use only the BMW-recommended coolant type.
How is BMW coolant blended?
Keep your cooling system operating at its peak performance by using BMW engine coolant (antifreeze). This 1-liter bottle works well for little top-offs of coolant that has been lost. For the best defense against boiling, freezing, corrosion, and lubrication, coolant is mixed with distilled water. For the optimum protection in street cars, mix distilled water with antifreeze 1:1. Reduce the amount of antifreeze in your coolant mixture if you want more cooling properties, but only in warm climates where freezing is not an issue. We advise monitoring the freezing point of the coolant mixture if you want to use antifreeze and water ratios other than 1:1.
Red Line Water Wetter can also be used with pre-ignition if high temperatures could lead to engine knocking.
- BMW # 82141467704, genuine German OEM antifreeze
- optimum cooling, freeze prevention, lubrication of the water pump, and corrosion resistance
Does my BMW require a special coolant?
In addition to controlling engine temperatures, the quality of your BMW coolant is essential for lubricating the water pump, guarding against corrosion and buildup, providing anti-freeze during the winter, and, in some models, assisting in cooling for engine and gearbox oil coolers. Not just any antifreeze will do; BMWs have special coolant needs (nitrite and phosphate free) to prevent build-up and corrosion of metal components. Along with BMW coolant, we also sell coolant additives like Red Line Water Wetter, which lower combustion chamber temperatures and elevate boiling points in order to prevent detonation and banging.
What sort of coolant is suitable for my BMW?
For BMW vehicles, the ZEREX G-48 coolant is perfect. The coolant, which is made for both diesel and gasoline engines, contains low-silicate, pH, anti-phosphate technology that guards against corrosion in all metals, including aluminum.
It is diluted at a 1:1 ratio to protect the modern engine’s components from freezing in the winter and boiling over in the summer. Additionally, the combination is prepared in 5:7 ratios for maximum protection. It also includes a high-quality defoamer system and contains less silicon than the vehicle’s mandated 250 parts per million.
Is the BMW coolant blended already?
BMW coolant is not pre-mixed when purchased. Simply purchase a gallon of coolant and a gallon of distilled water, then prepare the mixture as necessary. I would simply add a cup of distilled water if it only requires, say, a cup of coolant or water.
Why is the coolant in my BMW low?
You should take your automobile to the automotive service shop as soon as possible for an inspection and maintenance if your coolant is low because it could be an indication of a larger issue. Some of the causes of a possible coolant shortage in your car include the following:
- reservoir leak or overflow tank
- a radiator leak
- radiator hose leak
- water pump leak
- cracked or compromised radiator seal
- defective head gasket
Is water need to be added to BMW coolant?
To make the best coolant, they must be mixed. You can purchase antifreeze that is full strength and needs to be diluted with distilled water before being applied to the engine system, or you can purchase ready-made combinations of coolant that already have water added.
I have a BMW, can I use any blue coolant?
Now they can all work together. Ethylene Glycol serves as the “Active Ingredient” in “BMW” Coolant in addition to distilled water. Also concur with the distilled water
What is the price of BMW coolant?
A BMW 328i coolant change typically costs between $276 and $315. While materials are priced at $124, labor costs are projected to range from $151 to $191.
BMW coolant is what color?
To maintain your cooling system operating at its peak, we advise using only German OEM BMW engine antifreeze, part number 83192468442. (83 19 2 468 442). Because they don’t include nitrites, amines, phosphates, or borates, BMW exclusively suggests specific coolants. It is not permitted to use store-bought coolant from a nearby parts retailer.
2018 saw the introduction of this new green coolant, which has replaced the previous blue coolant. Green can be used on automobiles before 2018 and is backwards compatible with blue. BMW advises against using the older blue formula on vehicles created after January 2018.
The silicates in the green coolant provide further protection for the cooling system’s internals, although the coolant needs to be changed every two years.
For increased corrosion resistance, anti-freeze defense, and water pump lubrication in street cars, we advise combining distilled water in a 1:1 ratio with the mixture. Reduce the amount of antifreeze in your coolant mixture if you want more cooling properties, but only in warmer climates where freezing is impossible (see chart below). We advise monitoring the freezing point of the coolant mixture if you want to use antifreeze and water ratios other than 1:1.
Red Line Water Wetter can also be added if high temperatures could lead to engine banging or pre-ignition.
Original BMW HT12 antifreeze from Germany, part number 83192468442
Why is blue coolant used by BMW?
To maintain your cooling system operating at its peak, use only German OEM engine antifreeze, component number 82141467704. (82 14 1 467 704). Because they don’t include nitrites, amines, phosphates, or borates, BMW exclusively suggests specific coolants. BMW cooling systems typically do not work with off-the-shelf coolant from a neighborhood parts store, and mixing various coolant formulas is not advised (in a pinch you should use distilled water).
The well-known blue coolant, which has been in use since the 1990s, is only permitted for vehicles with model years up to 2018. Internally, it is referred to as the G48 formula and is exclusive to BMW/MINI vehicles. In comparison to other forms of coolant, the blue coolant formula is a hybrid that extends coolant service life and is less harmful to the environment. On vehicles manufactured in 2018 and later, BMW replaced it with a new formulation that contains silicate and offers superior immediate corrosion protection. BMW does not advise using the older blue formula for vehicles created after January 2018.
Can I simply add coolant on my own?
Add the proper coolant to the reservoir if the coolant level is low (not the radiator itself). Either diluted coolant alone or a 50/50 blend of concentrated coolant and purified water are acceptable. Replace the cap and tighten it until you hear a click when the coolant reaches the cold fill line. Shut the hood.
What happens if you fill your automobile with the incorrect coolant?
The performance of the car can be hampered if the wrong coolant is used or if several types are mixed together. Additionally, the radiator’s corrosion may worsen. It’s crucial to remember that color alone cannot accurately identify the type of coolant you should use. The radiator, water pump, radiator hoses, cylinder gasket, and other components can suffer corrosion and other issues as a result of using the incorrect coolant. Having a qualified auto mechanic handle your vehicle’s maintenance is the greatest method to guarantee that you obtain the right coolant.
Do I have to wait to drive after adding coolant?
After adding coolant, how long should I let the engine run? The most crucial thing, he continues, is “your own safety.” The engine, hood, and any leaking coolant can all cool down by waiting for at least 15 minutes.
Is it acceptable to combine fresh and old coolant?
There is no issue with combining different brands, and as long as they are of the same type when combining old and new, there is no issue.
Can I operate a vehicle with little coolant?
Electric cars, hybrid cars, diesel engines, and gasoline engines all inherently produce heat. Some of this heat is directed into the interior of your automobile when you turn on the heater for comfort. However, there are other ways to control the majority of the heat.
Your car relies on a liquid known as antifreeze, sometimes known as engine coolant, to guarantee that the engine maintains an ideal working temperature. Driving with insufficient coolant could cause your engine to overheat, which is usually bad for your engine, your car, and your trip!
Are antifreeze and coolant the same thing?
Antifreeze, commonly referred to as engine coolant, is combined with water to prevent the radiator from freezing in extremely cold weather and overheating in extremely hot weather. Knowing which coolant type is best for your automobile or truck is crucial because there are numerous varieties available.
The coolant warning light turned on for what reason?
The light should turn off after you start driving and the engine has heated up, even though the indicator is informing you that the fluid level is below the sensor. Check your coolant levels and the coolant sensor if your coolant light remains on even after a short period of driving.
What symptoms indicate low coolant?
After a while of driving, you get used to where your temperature gauge is when everything is in order. One of the most telling signs that anything is amiss with your cooling system is if it begins to lean toward red. If you see this while driving, stop, then lift the hood. By doing this, you’ll be able to start identifying the issue and help the engine cool.