When the LED light starts to blink, press and hold a button on the key fob. This will prove that it was coded.
- The original owner’s manual contains the immobilizer code. If you lose the code, the manufacturer can give it to you.
- Porsche remote
- Starter key
In This Article...
catoverlord
Therefore, I recently purchased a used 2015 Macan S that included a Key FOB. The vendor quoted me a price of about $650 plus tax. Here is a detailed explanation of how I managed to do it for $130. YMMV.
There are many of reasons not to attempt this: you might damage trims (I did), removing the trims would take a few hours, you might not feel comfortable sending your BCM module to a complete stranger on YouTube, the area under the dash is somewhat confined and gloomy, and so on.
- Cutlery puller
- T25 Torx bit
- removers for plastic trim
- Used Porsche Key purchased from eBay should operate with any 3 or 4 button remote.
- eBay’s blank blade
Steps:
Take the hood release off. The back of the assembly has a plastic tab. Release the plastic tab (goes towards the engine). Pull the hood release slowly this time, in the direction of the passenger door.
2. Raise the sill trim on the door. Several clips are holding it in place, thus the trim puller tools should be helpful. Pull out slowly, starting at the thin end (close to the driver’s seat).
3. Set away the entire trim piece when it has been removed.
4. The trim that covers the lower side of the steering column must now be removed.
5. On either side of the airbag, under the trim, are two more T25s. Remove those as well.
6. Use the puller tool to move the vent close to the screen. Be like me and don’t break a vent. Your life will be much easier with the puller.
7. The final T25 holding the panel can be found inside that cavity (the hole without a screw in the picture below). Remove it, of course.
8. Move about and detach the clips with your trim tool. You may wish to exercise caution.
9. You must remove the cables after the trim becomes loose. There is only one connector on the steering wheel’s right side (the yellow cable in the picture above)..
Barryng
In my opinion, it is crucial to have a third key FOB so that you can start the vehicle in the event that the one you regularly use is accidentally misplaced. I have been purchasing an extra (third) FOB for each of my cars since wallet keys that can start the vehicle are no longer provided. I keep this FOB well apart from the one in my pocket to reduce the likelihood that both will be accidentally lost at the same time. I regularly travel without my second FOB because it is in my girlfriend’s backpack and she isn’t always with me while I’m away from home.
The BMW dealer demanded $225 (on top of the $325 price of the new FOB) to program new FOBs for both of my BMW X3s. It turns out that a new BMW FOB can be readily programmed by starting the car while holding it next to the right position on the steering column for a FOB that is already programmed. The “needed” fees for computer programming imposed by the vendor are not necessary.
Now that I have my new Boxster, I must purchase a third FOB. I will undoubtedly need to pay $474 for this FOB through the parts department, which is to be expected. However, it would be good to avoid paying the dealer the additional $160 to $180 that he maintains is required to program it (plus a 150 mile round trip to the dealer just to do this).
Before I shell out even more money for the enormous bottle of Vaseline that will also be necessary if the dealer needs to do this, I want to make sure the new Porsche FOB must be programmed using the dealer’s computer.
Who is able to program a Porsche key fob?
Up to the most recent models, key fob programming can be done independently by someone having access to PIWIS III and a Porsche contract (we do it for clients). From 981/991 onward, this connectivity to the Porsche servers for key fob programming has been available.
Sadly, there aren’t too many independents using the more recent diagnostic tools.
I just spoke with a reputable and established neighborhood independent store. They could program a new key FOB using local software up until recently, however Porsche recently modified the process. It seems that a dealer is now the only one who can do it, and all the dealer really needs to do is connect the automobile to their computer. The vehicle’s computer then links to a Porsche server in Germany, and all security data, etc., required for activation and FOB verification are handled directly between the car and Germany. I was informed that the forms, which were previously filled out with all the security information verification, are no longer in use.
I also discovered that going to a well-known neighborhood shop with ties to a nearby dealership is far less expensive than doing so. A new FOB would cost $474.90, according to the parts guy at my selling dealer, and activation would add another $160 to $180. By using the neighborhood independent shop, which will also set up a meeting with a nearby dealership to activate it, I will save more than $200. They said the actual procedure only takes about 35 minutes.
Without the original, how can a key fob be programmed?
After locking every door, turn the ignition off. Set the accessory or “ACC” position on the ignition key. The door locks will cycle once once you turn the ignition key off once more. To program the key fob, press any button three times straight.
Can I set up a new key fob on my own?
Many automakers have started designing vehicles with locks that can be unlocked with little more than a key fob since the development of remote technology. The owner of a key fob can easily unlock a door by pressing a button, and many of them can also start their car by pressing a button as long as the fob is inside.
Unfortunately, the dealership may assert that they have property rights over the device and, as a result, only they can make a copy and program it, which comes with an outrageous charge, if a car owner loses their key fob or wishes to make an extra copy. However, while making a new key fob and programming it to function with your automobile may require expert guidance, a knowledgeable locksmith may help you with this task without forcing you to go back to the dealership for assistance.
But hold on, is it illegal to create a new key fob without the dealer’s consent?
Some dealers can even claim that if the task is not carried out by a licensed operator, making a new key fob is illegal. However, even if this might be the case with a leased or rented car, you are probably allowed to create as many copies as you want with the assistance of a professional.
Additionally, programming a key fob to work with your car is also not a difficult process. While you shouldn’t attempt to manufacture a copy yourself, a skilled locksmith can provide you with a new key fob quickly.
Can a key fob be programmed without visiting the dealership?
Can a key fob be programmed without visiting the dealership? Yes, you can program the key fob’s locking and unlocking features without visiting the dealership. However, you might need to visit the dealership or a locksmith if you need to program the transponder in order to be able to start the car with the key.
How much time does programming a Porsche key take?
Both Porsche and Audi keys have a microchip inside that needs to be programmed into the car for it to start. We need to have EVERY existing key, as well as the new key, so they can all be programmed simultaneously during the two-hour programming process.
Can a Porsche key be programmed by a locksmith?
A locksmith can handle every aspect of replacing your Porsche automobile key. They can frequently work more swiftly and obtain replacement parts more quickly. The most expensive option is probably to purchase a new Porsche key from the dealership.
How is the Porsche Macan key fob reset?
Locate it in the MFD settings, make the necessary changes, and then save the key with the new settings. Locate it in the MFD settings, make the necessary changes, and then save the new key settings.
Can key fobs be programmed via an app?
Programming EZ Key The EZ Key mobile app is used as the first application-based key programming tool to program nearly all vehicle models and key kinds, including transponders, remotes, and fobs.
Can key fobs from third parties be programmed?
Online purchases of aftermarket electronic car keys may include pre-programmed versions from the customer’s prior vehicle. Since the automobile it is designed to open is not close, it is almost impossible for a typical person to see it.
You cannot reprogram an aftermarket electronic car key once it has been programmed. Make sure the item you are buying hasn’t been used on someone person’s vehicle before. Transponder keys make it simpler to verify this since the key blade can be examined. It is almost certain that an aftermarket electronic car key has been programmed if it has been cut.
Why isn’t my Porsche key working?
It’s likely that your Porsche key fob requires a new battery if it has stopped functioning. For a replacement, drop by or give our Porsche parts department a call. The battery in your key fob will ultimately become worn out from constant use, which means the time will come to replace it.
How much does it cost to program a key fob?
What is the cost of programming a key fob? The typical person who programs key fobs is a locksmith. Typically, key fob programming costs between $85 and $400. Nowadays, most cars come standard with key fobs, often known as remote fobs.
What is the operation of Porsche keyless entry?
When you grab the door handle while holding your key in your hand, the system automatically verifies the encrypted access code on the key. The door will unlock once your code is verified, allowing you access to your car.
What should I do if my Porsche key is lost?
- Always start by requesting a quote. Give the automotive locksmith all the details, even if you believe they may not be important, and be as specific as possible while describing the issue.
- Additionally, the process can be sped up and made more reasonably priced if the locksmith has all the information. To avoid a lengthy waiting period, don’t forget to inform them your precise location. The pricing may also be impacted.
- As far as you are aware, let the locksmith or dealer know if the ignition has ever been changed. Different keys for the ignition and doors could be the result of a previous ignition replacement.
- Nowadays, the majority of Porsche models come with transponders or chips, so be careful to state the precise year, make, and model. You should also inquire with the locksmith about whether they have the necessary equipment in their truck to code the key. Not every locksmith has a device for programming keys, called a key coding machine.
- The VIN number should also be available because the locksmith could require it.
- Finally, keep in mind that if you lose your car keys, you do not necessarily need to tow the vehicle to the dealer. Try contacting AAA or a car locksmith who should be able to make you a new car key right away.