the foundation of
In This Article...
Is it possible to change a headlight on your own?
- Pick a spot with sufficient lighting in your garage or a tidy portion of your driveway to work on your car. Be calm and give yourself plenty of time (at least two hours) to change a headlight. It can be straightforward, but it also might turn out to be trickier than you anticipated.
- Any fasteners and retaining clips you’ve taken off should go in a container or jar. Otherwise, they’d be too simple to lose.
- Mark the location of the wiring removal with masking tape and a felt-tip pen to ensure that it is reinstalled accurately.
- Kneeling or working beneath the car can be made more comfortable by using an old throw rug, a rubber mat, or a sizable piece of clean cardboard to lie on.
- When connections are made, keep an eye out for a loud click.
We anticipate that your headlight replacement efforts will succeed if you follow these advice. We also hope that you don’t need to replace as many bulbs as this guy:
Will headlights be replaced by Autozone?
To be clear, buying a headlight or tail light for a vehicle at AutoZone is pretty simple if you have the part number for it or simply know the make, model, year, and occasionally even the trim of the car. When you visit a dealership or repair facility, labor is frequently added to the cost of the headlamp.
If your headlamp is easily accessible to the installer and is in most cases, Autozone will replace it.
Is it challenging to switch headlights?
Even if you have the most expensive wheels, if your headlights aren’t working, it won’t mean much (and as we know from numerous movies and cop shows, a burned-out light will lead to an unwelcome stop by a highway patrol car). Thankfully, changing a headlight bulb is a rather simple procedure.
Tools required:
- brand-new light bulb(s) Make sure you purchase the appropriate bulb type for your car (your local auto parts store should be able to match a bulb with your make and model)
- alcohol-based tissues and wipes (to clean and hold the new bulb)
- tool for Phillips screws
Instead of from the front of the automobile, you’ll access your headlight bulb via the engine compartment. Locate the headlight close to the front of the car by opening the hood. It will be housed in a bulb holder and connected to the bulb by a power connector, which typically has three wires.
Depending on your vehicle, the power cables are connected to a plug at the base of the headlamp and secured by a plastic catch, a metal clip, or a screw cap. Push down on the little lever at the top of the plastic catch as you take the plug out. Hold onto the metal clip as you draw it up and away if you’re dealing with one. When working with a screw cap, turn it counter-clockwise to unscrew it.
Holding onto the base of the old bulb, you should be able to remove the back of the headlight holder after the wires have been severed. In some circumstances, you might need to slightly spin the bulb to release it.
Use tissues or gloves to handle the replacement bulb; you don’t want your skin’s oils to get on it. Before you install it, you should give it a thorough cleaning with an alcohol wipe. When the bulb is prepared, insert it into the plug’s base. No rubber gasket will be seen if it has been placed properly. The headlight holder and power wires can be plugged back in when the bulb has been installed. Make sure to switch on your headlights to test the bulb.
Working with your headlights differs slightly from changing your rear tail lights, which include your brake lights. On some models, you may unscrew the housing that houses the bulb from the outside, while on other models, you have to do so from inside the trunk. To access the bulb after unscrewing the housing, you might need to work with tabs, screws, or tiny knobs on the tail light cover (make sure not to lose the screws if you need to remove them). The electrical wiring won’t need to be taken out, but be careful not to pull the housing out too much lest you rip the wires.
The bulb should be easy to remove by either pulling it out straight (as in most contemporary cars) or by pushing it in while simultaneously unscrewing. Replace the housing and reattach it when the replacement bulb has been installed (screws, tabs, knobs, etc.). Once more, be careful to test the bulb by turning the ignition on and using the brakes.
My headlamp will be changed by Oreillys.
While you wait, at no cost to you, our parts specialists can swiftly and easily change wiper blades because they are experts at changing headlamp and taillight bulbs.