These three things ought should be available right away, but if you’re not sure where any of them are, find them and move them to a designated location in your car or on your workbench. All fine, let’s go on.
1. Raise the hood of the car.
2. Remove the dust cover and power connector. On the back of the original headlamp is where the power hookup is located. It might be necessary to give the connector and dust cover a tiny twist to release them.
3. Removing the bulb from the housing. If there is a release clip, use it to press the bulb until it comes loose. Avoid grabbing the bulb by the glass.
4. Align the housing of the brand-new bulb with the vacant socket. Make sure the bulb is securely inserted by inserting it slowly.
5. Reinstall the lightbulb. Make sure the bulb is secured in by turning it.
6.) Replace the dust cover and power connector.
7.) Turn on the headlights to make sure they’re both working.
You’re all set. The following quick advice is intended to assist you the next time one of your headlights fails.
In This Article...
On a Kia, how do you replace the headlight?
Connect the bulb after removing the bulb cover. Remove the bulb by unsnapping the holding wire. Replace the cover after replacing the new bulb, connecting it, and snapping the retaining wire into place.
Depending on the type of bulb, changing automobile light bulbs is different. Here’s how to replace a headlight bulb in an automobile.
1) Exit the vehicle’s engine.
2. Lift up the hood.
3) Rotate the headlight bulb cover counterclockwise to remove it.
4) Unplug the connector for the headlight socket.
5) To release the headlight bulb retaining wire, push it up while first depressing the end.
6) Take away the bulb.
7) Align the retaining wire with the groove on the new bulb, then screw the new bulb in place.
8) Connect the socket-connector for the headlight bulb.
9) Rotate the bulb cover clockwise to reattach it.
Visit an authorized Kia dealer or service partner if the position lamp or daytime running lamp (LED) is not functioning. Because they can’t be replaced as a single unit, these bulbs will need to be changed by a professional.
How can a headlamp be changed by yourself?
For instructions on how to replace the headlight in your specific car and which headlight bulb to buy, consult your owner’s handbook.
Step 4. Unscrew the old headlight
Zullo warns that every car is unique. “He claims that while you can reach the bulb with some autos, you can’t with others. Sometimes you have to remove the inner fender to reach behind it because the battery or air filter housing is in the way.
However, changing the halogen bulb is all that is required if you can get the headlight open. This entails carefully unlocking the bulb after examining how it is secured. Zullo cautions that if the clips that are being used here are broken, the entire headlight would need to be replaced. “According to him, you must first examine how it is connected, softly disassemble it, and then carefully reassemble it without touching the bulb’s glass.
Step 5. Screw in the new headlight bulb
Without touching the bulb’s glass, carefully screw in the new bulb. If you do, the oil and grime on your hands could cause the bulb to burst once it heats up. Your car’s hood should be closed. Your headlights ought to work perfectly again after installing the new bulb, allowing you to enjoy driving your automobile day or night.
Most of the time, changing a headlight is simple and doesn’t need sending your car to the shop. See what other do-it-yourself auto maintenance tasks are available.
My headlamp will be changed by Autozone.
To be clear, buying a headlight or tail light for a vehicle at AutoZone is pretty simple if you have the part number for it or simply know the make, model, year, and occasionally even the trim of the car. When you visit a dealership or repair facility, labor is frequently added to the cost of the headlamp.
If your headlamp is easily accessible to the installer and is in most cases, Autozone will replace it.
Is it challenging to switch headlights?
Even if you have the most expensive wheels, if your headlights aren’t working, it won’t mean much (and as we know from numerous movies and cop shows, a burned-out light will lead to an unwelcome stop by a highway patrol car). Thankfully, changing a headlight bulb is a rather simple procedure.
Tools required:
- brand-new light bulb(s) Make sure you purchase the appropriate bulb type for your car (your local auto parts store should be able to match a bulb with your make and model)
- alcohol-based tissues and wipes (to clean and hold the new bulb)
- tool for Phillips screws
Instead of from the front of the automobile, you’ll access your headlight bulb via the engine compartment. Locate the headlight close to the front of the car by opening the hood. It will be housed in a bulb holder and connected to the bulb by a power connector, which typically has three wires.
Depending on your vehicle, the power cables are connected to a plug at the base of the headlamp and secured by a plastic catch, a metal clip, or a screw cap. Push down on the little lever at the top of the plastic catch as you take the plug out. Hold onto the metal clip as you draw it up and away if you’re dealing with one. When working with a screw cap, turn it counter-clockwise to unscrew it.
Holding onto the base of the old bulb, you should be able to remove the back of the headlight holder after the wires have been severed. In some circumstances, you might need to slightly spin the bulb to release it.
Use tissues or gloves to handle the replacement bulb; you don’t want your skin’s oils to get on it. Before you install it, you should give it a thorough cleaning with an alcohol wipe. When the bulb is prepared, insert it into the plug’s base. No rubber gasket will be seen if it has been placed properly. The headlight holder and power wires can be plugged back in when the bulb has been installed. Make sure to switch on your headlights to test the bulb.
Working with your headlights differs slightly from changing your rear tail lights, which include your brake lights. On some models, you may unscrew the housing that houses the bulb from the outside, while on other models, you have to do so from inside the trunk. To access the bulb after unscrewing the housing, you might need to work with tabs, screws, or tiny knobs on the tail light cover (make sure not to lose the screws if you need to remove them). The electrical wiring won’t need to be taken out, but be careful not to pull the housing out too much lest you rip the wires.
The bulb should be easy to remove by either pulling it out straight (as in most contemporary cars) or by pushing it in while simultaneously unscrewing. Replace the housing and reattach it when the replacement bulb has been installed (screws, tabs, knobs, etc.). Once more, be careful to test the bulb by turning the ignition on and using the brakes.
Step One
Choosing a method to access the headlight bulb is undoubtedly the trickiest aspect of the procedure. Even though it looks like you should be able to just pop the bulb out, you frequently need to remove other components in order to reach the bulb.
On the majority of automobiles, the engine compartment is where you access the headlight bulb. Locate the headlamp within a bulb holder by opening the hood. For information on the optimum access points and any components that need to be removed in order to reach the headlight bulb, consult your owner’s manual as well.
Step Two
Analyze the best way to remove the old bulb. On some cars, the bulb is positioned directed into the headlight assembly, while on others, the bulb is fixed in the headlight assembly by a wire arrangement. You can take out the bulb once you understand how it is held in the housing.
You’ll also be able to decide at this time whatever tools you’ll need to finish the project. Some headlight bulbs do require the use of a flathead or Phillips screwdriver, but the majority can be removed without them.
Remove any power wires that are attached to the back of the light bulb. The back of the headlamp may also have a dust cover that needs to be taken off. The bulb may alternatively be secured in place by a clip or clips.
Step Three
By grasping the bulb housing and drawing it out, you can remove the bulb. You might need to twist some bulbs in order to remove the cap. When doing this, be careful not to risk shattering the bulb by touching it roughly.
Step Four
Clean the replacement bulb with an alcohol wipe or by using rubbing alcohol and a lint-free cloth before replacing it.
Insert the new bulb by aligning it with the available socket while holding it by the housing. Avoid touching the bulb as your skin’s oil may leave a hot patch, which could cause it to burn out more quickly. To avoid this situation, you can think about wearing gloves.
The procedure you used to remove the old bulb should be repeated. If necessary, reinstall the dust cover and attach any wires or clips. Place the headlight housing in the frame once again. If you had to remove any extra components to get to the headlight bulb, replace them.
Step Five
To test the new headlight’s functionality, start your car and turn on the headlights. Spend some time as well examining the headlights’ direction. Your lights may not be focused on the road, where you need them to shine clearly, if they are not properly aligned. Consult your owner’s manual for instructions on how to fix them if they appear to be out of alignment.
Find out more about high-quality lighting items, where to buy your car part, or how to locate it.
This article’s information is provided for educational reasons only and shouldn’t be relied upon in place of consulting a qualified technician or mechanic. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here. We will not, under any circumstances, be held responsible for any loss or harm resulting from your reliance on any content.
How much does a Kia headlamp cost?
The headlights are your Kia’s primary source of illumination at night, allowing you to see where you’re going and, more significantly, assisting drivers in recognizing other vehicles that are approaching them.
It is more cost-effective to replace just the bulbs in most current automobiles rather than the entire headlight.
The front of the majority of Kias has four headlight bulbstwo for the low beams and two for the high beams/dip lightsas well as individual fuses and relays for each side.
If the headlight assembly needs to be taken off the car, replacing a headlight bulb can cost anywhere from $20 to $100 or more.
Like most things, bulbs eventually deteriorate, corrode, fail, or just reach the end of their useful lives. The bulb will need to be replaced with a new one when this occurs. Driving without working headlights is prohibited. Since you never know when you might find yourself in a scenario requiring reduced vision, it is important to have a Kia bulb replaced right away.