You must restart the tire pressure monitoring system after adjusting the tire pressure or rotation (TPMS). The Mitsubishi Outlander’s TPMs can be reset in the following ways: 2014 2015 2016 2017 2018 2019 2020
In This Article...
Verify that the car is totally stopped
Put the gearshift lever in the N position (M/T) or the P position (A/T) while using the hand brake.
- The tire placard’s suggested tire pressure should be adjusted.
- Without starting the engine, turn the ignition to the ON position.
Press the Engine Start/Stop button twice without touching the brake pedal if your car has one.
- Until the SETTING MENU is visible on the cluster display, repeatedly press the button.
- In order to access the menu, hold down the button.
- the TIRE RESET location
- To perform the TPMS reset, press and hold the button.
Press the button until a buzzer sounds and the slow-flashing tyre pressure warning light appears.
Drive your vehicle until the warning light turns off after starting the engine.
How can I turn off the tire pressure warning light?
Don’t start the car; just turn the key to “on.” Till the tire pressure light blinks three times, press and hold the TPMS reset button. Press the button again to start the vehicle. Within twenty minutes, the light ought to turn off.
The TPMS reset button is where?
Tire pressure monitoring system is referred to as TPMS. The TPMS reset button is often located below the steering wheel. Your car’s TPMS needs to be electronically reset after you replace the tires in order to erase the error message. Hold the TPMS reset button down until the tire pressure light blinks three times, then let go of the button to complete the process. Your car should be started, and the sensor will refresh after 20 minutes.
Without a reset button, how do you reset a TPMS?
The system must be put in relearn mode in order to reset the light. Make sure the tire pressures are all set evenly and according to the specifications first. To prevent the battery from going out, you might need to first connect a battery charger on low. All accessories must be turned off. After turning the key to the “On” position for 20 minutes with the engine off, drive the car at a speed of at least 16 mph for at least 7 minutes. The light will turn off once the relearn operation is complete. If the light does not turn off, the system needs to be fixed. Tire pressure sensors may need to be replaced because they can start to malfunction after 5 or 6 years of use.
Why is my tire pressure light not resettable?
There is a three pound or so tire pressure tolerance on some cars, such the Toyota Prius. If the reset button is ineffective, try pumping up each tire to its recommended PSI plus three before deflating them all to almost zero. Re-inflate each tire to the recommended pressure indicated on the sidewall after that. Keep in mind that the spare tire may also have a sensor attached. To reset the sensors, travel a short distance at 15 mph.
Why are my tires in good condition but my tire pressure sign is on?
It’s likely that one or more of your tires have low air pressure if you see the tire pressure indicator turn on. However, even if your tires are in good condition, there are a number of things that could cause the sensors to go off, so you shouldn’t rely only on the data from the tire pressure monitoring system of your car.
We’ve talked about some additional aspects of automobile maintenance in this piece. Read these articles if you have some time:
Why does the tire pressure light remain on even after I have filled the tires?
If you’ve inflated your tires, but the air pressure warning light continues to flash, your tire pressure monitoring system is malfunctioning or you have a gradual leak. A bright TPMS warning light indicates a problem with a tire pressure sensor, assuming there isn’t a leak in your tire. One of them might be damaged, the lithium-ion battery might be dead, or the TPMS itself might have an internal problem. You’ll need to get your Tire Pressure Monitoring System repaired in any of these scenarios.
Quick Tip: Recheck the tire to ensure it is inflated to the correct air pressure if the TPMS warning light illuminates again after you have inflated it. Low tire pressure indicates an air leak, which requires repair or tire replacement.
Where are TPMS installed?
In the US, direct TPMS usage is more prevalent. The sensors are either housed in the tire pressure valve, which also serves as an antenna, or they are band-clamped to the wheel rim. These gadgets deliver the data to an on-board computer.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
How to reset your TPMS after tire service can be found in your vehicle’s manual or by asking your neighborhood Midas mechanic.
- Visual inspections of the brakes, battery, air filter, fluids, belts, and hoses are all included in the Midas Touch Courtesy Check.
When the tire pressure light is on, can I drive?
You should be able to find our store or an air pump if the light just came on and you need to get there. However, it is unsafe to keep driving while the light is on. This is why: When you drive your car with low tire pressure, you accelerate the premature and severe tire wear.
How long before the tire pressure light appears?
After a few kilometers of driving, the light may turn off if the tires are adequately inflated. After around 10 miles, if the light still remains on, it may be necessary to reset the TPMS as instructed in the owner’s handbook of the car.