How To Reset Lamp Timer On Mitsubishi Projector

Mitsubishi / By

Most projectors require you to reset the lamp operating time counter to 0 after changing the light. If the counter is not reset, the projector may prematurely indicate that the replacement light is worn out or may even refuse to turn on. You can either follow the procedures below or consult your projector’s manual to learn how to reset the light counter.

Never swap out the lamp before resetting the counter. We advise that you order a new lamp right away even if your old one is still shining brightly and the projector is beginning to suggest that its life is about to expire. Install the new lamp as soon as it is delivered, and save the old one as a backup. It is recommended to avoid exceeding the bulb’s lifespan because doing so considerably increases the risk of explosions.

Procedures differ depending on the projector model as well as between projector manufacturers. Here are a few illustrations to get you started:

  • Viewsonic, 3M, Dukane, and Elmo
  • To access the menu, click the “MENU” button.
  • Use the “ARROW UP” and “ARROW DOWN” buttons to select “Go To Advanced Menu…” when “EASY MENU” appears, then hit the “ARROW RIGHT” button.
  • Press the ARROW RIGHT button after selecting “OPTION” from the menu in the left column using “ARROW UP” or “ARROW DOWN.”
  • Press and hold the “RESET” button or the “ARROW RIGHT” button after selecting LAMP TIME from the “OPTION” (or “ADVANCED”) menu using the “ARROW UP”/”ARROW DOWN” buttons.
  • A dialog box is displayed. Using the “ARROW UP” button, select “RESET”.
  • Proxima, Infocus, and ASK
  • Approach 1:
  • Turn on the projector.
  • Press and hold the volume up (“Vol+”) button for at least three seconds before pressing and holding the volume down (“Vol-“) button.
  • The warning light ought to go green.
  • Approach 2:
  • Choose “About” from the menu (resp. “Info”).
  • Reset the counter by selecting “Reset Lamp Timer” and confirming it.
  • srie P/H/XD/X from Acer
  • On the projector’s control panel or the remote control, press the “MENU button.
  • To select Advanced setup, press the “Arrow up” and “Arrow down” buttons.
  • To select “Reset lamp hours,” use the “Arrow up” and “Arrow down” buttons.
  • To reset the lamp counter to zero, press the > button and select “Yes.”
  • To return to the main menu, press the “MENU” button on the remote control or the control panel.
  • Press the “MENU” button on the remote control or the control panel to close the OSD menu. The projector will save the modified settings and the OSD menu will exit.
  • To display the lamp counter, press and hold Exit on the projector control panel for five seconds.
  • To reset the counter to zero, press the Auto button on the remote control or the control panel.
  • The OSD will vanish after around 5 seconds.
  • Call up the OSD menu once the starting logo has appeared.
  • SYSTEM SETUP: “Advanced” > “Lamp Settings” should be accessed.
  • Enter the “MODE” or “ENTER” key.
  • A popup titled “Lamp Settings” will appear. Press the “MODE”/”ENTER” button and select “Reset.”
  • You’ll get a notice asking if you want to restart the lamp counter.
  • Press the “MODE”/”ENTER” button after selecting the “Reset” option.
  • The count of lamps will be reset to 0.
  • PB6100/PB6110/PB6200/PB6210 from BenQ
  • To activate the light counter, press and hold the “Exit” button on the projector control panel for 5 seconds.
  • Press “MENU” to restart the counter when the OSD menu displays, or “Exit” to end it.
  • Press the “Exit” button to exit the menu or the “Button” to reset the lamp’s running time to zero.
  • “LAMP HOUR RESET OK” will be displayed. To exit the menu, click the “Exit” button.
  • Canon, Christie, Eiki, and Boxlight
  • Turn on the projector and select “MENU” from the menu. You’ll see the “ON-SCREEN MENU” emerge.
  • To move the red frame to the “SETTING” icon, use the “POINT LEFT/RIGHT” buttons.
  • Select “POINT DOWN.” When the “SET” button is pressed, the red frame will move to the “Lamp counter reset” option.
  • You’ll see the message “Lamp replace counter Reset?”
  • The “Yes” and “SET” buttons should receive the red arrow.
  • You’ll see a second dialogue box with a request to confirm your selection. To reset the lamp counter to 0 click the “Yes” button.
  • The lamp indicator “LAMP REPLACE” will stop lighting up after the counter has been reset.
  • When the projector settings are displayed, press “MENU” and select “RESET” from the menu.
  • Select “Setting LAMP HOURS,” then press “ENTER” to confirm the reset.
  • The menu can be accessed by turning on the projector and pressing the “MENU” button.
  • Choose “LAMP TIME” from the “OPTION” menu.
  • The “RESET” button should be pressed and held for around 3 seconds.
  • To confirm, select “RESET.”
  • To open the menu, click the “Menu” button.
  • To access the “Information” menu, use the “Right” or “Left” buttons.
  • Select “Lamp Hour Reset” with the “Up” or “Down” buttons.
  • Either “Enter” or “Right” should be pressed. You will notice the message “Please check user manual.”
  • Press the “Down,” “Up,” “Left,” and “Right” buttons on the remote control in that order. There will be information about how to reset the counter.
  • Turn the projector on.
  • Hold the “ARROW RIGHT” and “ARROW LEFT” buttons down on the remote control while simultaneously depressing the “POWER” button on the projector control panel.
  • The lamp indicator will blink twice after 3 seconds.
  • To finish the lamp reset, let go of the buttons.
  • The NEC srie NP/U/LT/VT
  • Select “RESET” from the “MENU” menu by pressing the
  • Select “CLEAR LAMP HOURS”; a dialogue box will display; then click “OK.”
  • The projector won’t turn on if the counter has accumulated more than 3,100 running hours.
  • Put the projector on standby if this happens. For roughly 10 seconds, hold down the “ON/STANDBY” and “CANCEL” buttons on the remote control. The “LAMP” sign will stop glowing once the bulb counter resets to zero.
  • Activate the “Menu” button. To navigate to and select the “Settings” menu, press the “left” and “right” arrows (respectively, “3” and “4”).
  • To access “Lamp Counter,” press the “Arrow up” and “Arrow down” buttons. Click “Select.”
  • The screen will show the lamp counter. To confirm, click “Reset” and then “Yes.”
  • The “ENTER/ARROW right” and “AUTO SYNC” buttons should be pressed and held. Press the “ON” button, then the “ARROW left” button while still holding them down.
  • You will see “0000h” on the screen to indicate that the counter has been successfully reset.
  • Sharp XR10X, XR20S, XR20X, and XR10S
  • The “MENU/HELP,” “ENTER,” and “ARROW down” buttons should be pressed and held. Press the “STANDBY/ON” button while you are holding them down.

On a Mitsubishi, where is the reset button located?

Resetting a Mitsubishi TV

  • Pushing on the front panel will make it open.
  • Push the “System Reset” button using a pointed instrument, like the tip of a paper clip or the sharpened end of a pencil.
  • Wait until the green LED light on the front panel display stops flashing, which should take around a minute.

How can my projector be reset?

the projector’s reset

  • On the remote control, press the Home button.
  • Press Enter after selecting the symbol on the Android TV Home screen’s upper right corner.
  • Press Enter after selecting Device Preferences.
  • Press Enter after selecting Reset. A confirmation window appears.
  • To restart the projector, choose Reset and hit Enter.

What does a projector’s lamp time mean?

Projector bulbs, like every other type of light bulb, have an anticipated lifespan known as lamp life. The number of hours before the bulb dims to half its original brightness is stated in hours.

The expected lamp life will vary depending on the projector and lamp technology, however most projectors give roughly 2000 hours.

Since the success rate of the lamp is based on a bell curve, most (but not all) lamps will achieve the desired number of bulb life hours. Some lamps will burn out more quickly than others, and this is within the rating’s allowable working range.

The lamp will have the best chance of lasting the entire rated lamp life for projectors used under typical operating settings (no more than three to five hours per day in a clean, relatively dust-free environment).

How do you check the lamp hours on a projector?

Lamp hours are listed under the “Information” menu item on modern projectors. If your projector is an older model, you can briefly see the lamp hours on the screen by pressing and holding the projector’s Power ON/OFF button for around 20 seconds.

Where is the Mitsubishi mini split’s reset button located?

You must click the AC’s reset button to restart the tiny split “reset switch (found on the bottom).

Remember to flip the breaker back on after checking to see whether it has tripped “leave it off for about a minute, then switch it back on.

Does a projector have a reset button?

Navigate to the Advanced Settings by pressing the menu button on the projector or the remote control. 2. Pick resetting everything to factory defaults. Note that the reset button could be located slightly differently on some models.

How is a projector lamp tested?

If your projector doesn’t have a lamp status feature or if the findings are unclear, you may frequently determine if the lamp is defective by carefully examining the problem. Regular projector use will likely cause you to notice a loss in the contrast or brightness of the image before the lamp fails. Watch the image after turning on the projector. The lamp is about to die if it is flickering or wobbling. If the projector turns on successfully but no image appears, the light has likely stopped working entirely.

How can I make my projector lamp last longer?

A projector lamp has an anticipated lifetime, much like any other light bulb. How frequently you use the projector and the brand have an impact on how many hours the projector lamp lasts. Most projectors have a bulb life of between 1500 and 2000 hours. Here are eight suggestions for extending the life of your DLP projector lamp.

Observe the dust. The ideal setting for your DLP projector is one that is largely free of dust. Make sure your projector is not placed next to any open windows so that it can be exposed to external dust and pollen.

Prevent abrupt ons and offs. Each time the DLP projector lamp is turned on, a power spike is produced that strains the connections inside the light. When you are ready to use your projector, turn it on; try to avoid turning it on and off frequently.

Verify the heat. A projector that is overheated puts stress on the light and runs the risk of blowing up. Make sure the projector has proper airflow, especially if it is permanently installed. Never let the mounting plates obstruct the fan vent.

Allow it to rest. Avoid continuously using the projector. Every 24 hours, turn it off and let it standing for at least an hour. A projector lamp life that is used four to five hours per day on average will last longer.

Await cooling The cooling fan of your projector prevents the projector bulb from overheating. Before shutting off the projector, let the fan complete its cycle and shut off. The projector lamp may break if the switch is turned off before the projector has cooled.

Keep it tidy. Your projector’s air filters are intended to maintain airflow around it and prevent overheating. Keep the dust and debris off of them. Every three months, or more frequently if there is a lot of dust, make sure to clean the air filters. The lamp life of the DLP projector will be extended by routine maintenance.

Go eco. Some projectors offer a “Eco mode” or “Bulb Economy Mode” that lowers the brightness of the projector lamp by 20% while increasing lamp life by 50%. Most likely, you won’t even notice the reduction. You will need to manually change the lamp mode because the majority of projectors are sold with the factory brightness setting at its highest level.

Install genuine lighting.

Although generic bulbs may appear to be a good deal, they have a substantially shorter lamp life. These fake lamps, despite being marketed as “compatible,” are prone to explosions. The lamp life of genuine OEM projector bulbs is significantly increased. Avoid imitation projector lighting.

How long should a light for a projector last?

Although some bulbs can last up to 5,000 hours, most projector lamps endure between 1,500 and 2,000 hours. The majority of projectors will require one to two bulb changes at this time.