One CR2032 battery is also needed for this Audi key fob.
In This Article...
The battery in my Audi A4 key has to be changed.
You’ll require the following to replace the battery:
- Flip the metal key open.
- Using a little screwdriver, press the key’s back cover.
- At the keyfob’s end, lift the back cover.
- The battery is within the back cover, which you should remove.
- The positive side of the battery should be noted as you remove the battery.
What occurs if the battery on an Audi key dies?
Early Audi vehicles lack a Start/Stop button in favor of using a slot in the dashboard. To start or stop the car, one must push the actual fob. The car will already detect the key fob when inserted, even if the battery is dead.
An Audi key fob’s battery can be found where?
Replace Audi Remote Battery Using a little screwdriver, press the key’s back cover. At the fob’s end, lift the back cover. The battery should be inside if the back cover is removed. Remember the orientation before removing the battery.
Why isn’t my Audi key working?
Audi models from 2000 to 2014, including the Q5, R8, A6, A8, Q7, A4, A3, TT, Allroad, A5 and A7, are covered by this TSB.
Although central locking by remote control no longer functions either continuously or intermittently, the locks can still be opened by hand. Because the battery has been disconnected or the remote control’s battery has been changed, the remote control key and vehicle may not be in sync. The remote control key may have been momentarily turned off if other senders (such as mobile phones, TV stations, wireless headphones, etc.) use the same frequency band. This is because it is impossible to clearly indicate the remote control key. This is required to stop other unconnected senders from accidentally unlocking the car.
To synchronize each remote control key with the car, do the following:
- Use the key to mechanically start the car.
- Depress the remote control key’s unlock button.
- Turn the ignition switch to the ON position after inserting the key.
- Reset the key to OFF and take it out of the lock.
- Press the remote control key’s locking or unlocking button.
- 2002 model year or later: Use the VAS scan tool to program the remote control key(s) to the Central Comfort System control module (address word 46) if the synchronization procedure did not work. Implement test plan J393-central control module for comfort system while adjusting the remote control key (channel 21). Sometimes after the “The test strategy of erasing all memory places first yields better outcomes.
- On the remote control key, press a button.
- With the key, lock or unlock the car once mechanically.
- The entire operation cannot go on for more than 30 seconds.
- Up until and including model year 2009: Use the VAS scan tool to program the remote control key(s) to the Central Comfort System control module (address word 46) if the synchronization procedure failed. adopting the remote control key and testing plan J393central control module for comfort system (s). occasionally after “The test strategy of erasing all memory places first yields better outcomes. Adapt the remote control key(s) to the BCM2 (vehicle electrical system control unit), address word 09, using the VAS scan tool, starting with model year 2010 if the synchronization procedure did not work. Adapt the remote control key as per test plan J519-Vehicle Electrical System Control Module (s).
Should a key fob be reprogrammed following a battery change?
A remote key fob needs to be associated with your vehicle particularly in order to be secure.
This stops people who drive the same make and model of automobile as you from using their remote to access your car. You’ll need to reprogram the fob if changing the batteries has erased this connection or if it was somehow disrupted in order for it to once again recognize your automobile.
Standard programming sequence
Your key fob can typically be reconfigured by following this typical procedure:
Instead of starting and then returning to the locked position, turn the key into the run position. Repeat this multiple times.
You’ll typically hear a chime or other sound when you’ve cycled the key enough times. At that point, you can push the lock or unlock button on your key fob to hear another chime.