- Find the jack kit, the jack handle, and the lug nut wrench.
- Pre-Jack List: Actions to take prior to lifting a car.
- Position Jack: Put the jack handle together and place the jack beneath the jack points.
- Vehicle Lift: Lift the car securely using the jack.
In This Article...
How do you use the jack on an Audi a4?
If you are jacking up the front wheel, the jack goes directly behind it; if you are jacking up the rear wheel, the jack goes directly in front of it. There ought to be a small mark along the rail. Start elevating the car after positioning the jack beneath the location. Raise the vehicle enough to be able to fit a jack stand underneath it.
How should the jack on an Audi A3 be used?
You can raise one side, then set down your jack stand; after that, raise the other side and set down your second jack stand. The jack stands can be mounted on the A-arm on the front. The jack stands can be placed directly next to the jack itself on the back of the ball attached on the frame.
On an Audi A5, how do you operate the jack?
Put the vehicle in first gear (manual transmission) or position P on the selector lever (automatic gearbox).
Find the marking (recess) on the door sill that is nearest to the wheel that has to be replaced. Fig. 1. The marker on the door sill is in front of the jacking point.
Turn the jack up until the claw completely encircles the seam on your Audi A5 (Fig. 2 -A).
Place the jack in the proper position so that the claw of the jack (A) fits around the seam and the jack (Bmovable )’s base plate is flat on the ground. The jacking point (A) must be supported vertically by the base plate (B).
In order to attach the crank handle to the jack, place it inside the knob’s opening. To fix the crank handle in place, turn it either clockwise or counterclockwise.
Wind the crank handle to raise the Audi A5 till the problematic wheel is off the ground.
Only the jacking points indicated on the door sill in Fig. 2 may be used. Each wheel has its own jacking point. Apply the jack only where indicated. Caution!.
The Audi A5 may fall off the jack if there was an unstable surface underneath it. Always provide the jack a stable basis to stand on. Use a sizable, sturdy board or another type of support if necessary. To keep the jack from slipping on a hard, slippery surface (like tiles), use a rubber pad or something comparable.
- Reduce the danger of damage by keeping the jack’s base from slipping.
- Only position it and apply the jack at the proper jacking places. The Audi A5 could roll off the jack and cause injury if it is not placed firmly.
It is forbidden to raise the Audi A5 on its sills. The Audi A5 may sustain damage if the jack isn’t used at the jacking points that are behind the markings on the door sill.
When changing tires, should the automobile be in neutral?
If an issue were to arise with one of your car’s current tyres, you might find yourself needing to change a tire.
If you follow the correct technique while changing a tire, even if you’ve never done it before, you should be fine. You can learn more about what to do in our changing a tyre tutorial here.
Here, we’ll concentrate on common errors that a novice tire changer could make and explain why you should steer clear of them.
DON’T change a tyre at the side of the road
The greatest places to change tires are places that are far away from the road. You’d be better off calling a breakdown service if you discover that a tire suddenly requires replacing while travelling on the road and you can’t safely stop your car somewhere away from the road.
It is challenging to do a tire replacement right alongside the road because you need a decent bit of space to do so securely and properly. Not to mention that you would be unnecessarily endangering yourself and other road users. Another major no-no is changing tires on the hard shoulder of a highway.
DON’T change a tyre on loose or uneven ground
If you’re going to change a tire on your car, you should do it where the ground is level and smooth.
Attempting a tyre change on somewhere that is gravelly or on a grassy surface is a bad idea because it’s more uncomfortable to work on and there’s a risk that things like the jack could slip while in use.
DON’T have any passengers in the car
Imagine that you had to change a car tire on short notice and that you were able to locate a location that would be adequate for the task. Before you start changing the tire, make sure all of your passengers, including any animals, have exited the car. Make sure they travel somewhere safe that is not near a vehicle or a busy road.
A person moving around inside the vehicle while changing a tire adds extra weight that could be obstructive and will just make the task more difficult than it needs to be.
DON’T do any checks or work under your vehicle while it’s raised on a jack
To prepare your automobile for a tire replacement properly, you’ll need a car jack. However, using this tool to perform lengthy work below your car is not recommended.
Therefore, resist the urge to even glance below your car while changing a tire, even if there is something else about the automobile you want to inspect.
You need the proper tools to perform any type of maintenance on your automobile that involves spending time underneath it, or you can get it serviced. Working underneath your car is not secure enough with only a car jack.
DON’T use the jack anywhere you’re not supposed to
A car jack should only be used on particular parts of an automobile. When replacing a tire, you should position the jack at the suggested lifting point near the removed wheel.
If you don’t install the jack correctly, you risk damaging your car’s undercarriage and risk having an accident since the jack may not support the car securely. To determine the proper lifting points, see the owner’s manual for your car.
If you don’t have the owner’s manual handy for whatever reason, you can look for information online or get support from your automobile manufacturer’s customer care.
DON’T leave the car in neutral
It’s crucial to remember to leave the vehicle in the proper gear when changing a tire on a manual transmission vehicle. Naturally, you should turn off the engine before beginning the tire change. However, you should leave the gearstick in either first or reverse.
The handbrake only works on two wheels, often the rear wheels, which is why you want to do this. With the engine turned off, shifting into first or reverse causes the front wheels, which are typically the driven wheels, to lock.
If your vehicle has an automatic transmission, you may leave it in the “Park” or “P” position.