How To Turn Off Valet Mode On Audi A4

Audi / By

Press the VALET button to turn on the valet parking feature. The button’s LED will start to glow.

(Applies to cars with a lockable load hatch and lockable backrests:) Lock the load-through hatch, rear backrests linko and linko, and the baggage compartment to prevent entry from inside the car.

While keeping the emergency key on you, give the remote control key to the service workers.

The following buttons are inactive when the valet parking feature is on:

  • Activate the driver’s door.
  • key on the remote control has a button.
  • On the boot lid’s release catch

Every time you turn the ignition on with the valet parking function engaged, the message “Valet parking active” will show up in the instrument cluster display.

Please be aware that the luggage compartment can be accessed from inside the car even while the valet parking feature is engaged for vehicles with fixed backrests and vehicles without lockable backrests.

How does an Audi’s valet parking function?

Push the stalk on the left side of the steering column forward (toward the front of the vehicle) and up to switch the valet mode off (remote start on) (towards roof). Maintain for three seconds (parking lights will flash).

What does Audi A4’s valet button do?

1 Glove box: Valet parking function button. Regarding the Audi A4s: it has a valet parking feature. The luggage compartment is kept safe from unauthorized access thanks to the valet parking feature. You can engage the valet parking function to have your Audi A4 parked, such as by service employees.

How do I unlock my car’s valet mode?

Exiting Valet Mode

  • Turn the “ON/RUN” switch while inserting the key into the ignition of your car. Do not start the car.
  • Lock and Trunk (buttons I and III) should be simultaneously depressed and released.
  • Try remote starting your car after taking the ignition key out.

Where is the switch for the valet?

The VALET switch’s location will vary since the installer chooses the location. Rarely, the installer might choose not to install the VALET switch.

Typical valet switch locations:

  • beneath the driver-side dashboard (mounted in the under-dash covering trim panel or wire-tied to a harness)
  • mounted in the kick panel on the driver’s side.
  • mounted inside the plastic body of the steering column.
  • behind an access panel or door to a fuse block.
  • On the back of a pocket, low in the center console.
  • adjacent to the fuse block.
  • within the glove box.
  • Additionally a push-button, the LED itself (select model systems)
  • More recent systems will have an antenna installed on glass. This antenna contains the valet switch.

If you are unable to find your valet switch, contact your installer or dealer and ask them to do so.

On an Audi A5, how do you disable valet parking?

Press the VALET button in Fig. 1 to start the valet parking service. The button’s LED will start to glow.

To prohibit entry to the luggage compartment from inside the car, lock the load-through hatch and the rear backrest with the emergency key. This rule applies to vehicles with these features (Link and Link).

* Turn the driver’s door on.

Please be aware that even when the valet parking feature is engaged, luggage compartments in vehicles without lockable backrests can still be accessible from inside the car.

Audi valet alert: what is it?

When an app’s functionalities are grayed out, any of the following circumstances might be true:

  • You haven’t been approved as a Key User for your car. Your account and your car are not currently paired. You don’t currently have a trial or membership for Audi connect PRIME.

Features (including Vehicle Status Report, Lock Unlock, and Car Finder) available to owners of 2017+ Audi Q7, A4, allroad, 2018+ Audi A5 & Q5, and 2019+ Audi A6, A7, A8, Q8 vehicles with Audi connect* can only be utilized by a myAudi account identified as the Key User.

What if I’ve already paired and become a Key User but none of my features are active anymore?

If you are a Key User but some features are grayed off, one of the following situations may be true:

Thanks to convenient Audi connect features, you can lock and unlock your car with the myAudi smartphone, receive a status report about it, and even locate it in a parking lot. Vehicle Status Report *, Car Finder *, and Remote Lock/Unlock * will be a part of Audi connect CARE * by March 8, 2019, so you’ll still have access to them whether or not you decide to keep paying for Audi connect PRIME * after your trial or subscription period has ended. Your vehicle comes with Audi connect CARE, which also offers Emergency Call, Online Roadside Assistance, Stolen Vehicle Locator, and Audi Service Request.

You have the option to grant access for location services, accessing contacts in the vehicle, using the calendar in the vehicle, and push notifications while setting up the myAudi app. Once the app setup is complete, you can change any of these permissions by going to your phone’s settings menu, selecting the myAudi app, and selecting which information myAudi may access.

The main goal of the myAudi app is to keep you connected to your car. For more account management options, including access to your Audi Financial Services account, log onto the myAudi site. Please anticipate frequent changes to the myAudi app and myAudi portal as we are continually working to enhance your ownership experience.

This occurs as a result of the car sending the door status when it is switched off. After this status of the ignition being off is sent, it’s possible that the car is locked. Check for warning messages or refresh the app by pulling down from the top and choosing the “Retrieve data from vehicle now” option to get the most recent status.

With speed alerts, you can specify a maximum speed for Audi and get a notification if your car goes above that restriction. If push notifications are enabled in the device settings, this feature is accessible. Please be aware that the speed alert feature does not stop vehicles from going beyond the specified top speed.

You can designate a perimeter around the location of your Audi using geofence alerts, and you will be informed if the car enters or leaves the region. You’ll receive a notification when the vehicle enters or leaves the designated radius. If push notifications are enabled in the device settings, this feature is accessible. Please be aware that Geofence warnings do not stop vehicles from entering or leaving a specific area.

You may set a maximum speed for your Audi and a boundary with valet warnings. If the vehicle enters/exits the designated radius or goes beyond the predetermined limit, an alert will be delivered. If push notifications are enabled in the device settings, this feature is accessible. This makes the assumption that you are physically close to your car (for example, when going out to dinner) and uses the phone’s location services to pinpoint the border. Zoom out and place a pin in the vicinity of the vehicle to turn on the Valet alert to choose a new location. Please be aware that Valet notifications do not stop drivers from going over the designated top speed limit or from entering or leaving a certain area.

When the myAudi app is open and logged in while the phone is linked to the car’s Wi-Fi hotspot*, online radio is still accessible. The ability to set favorite stations within the app has been removed.

In the app, go to the Profile tab >> User management >> PIN to modify the four-digit remote services PIN that you use to remotely lock and unlock your car. You will have to enter your vehicle’s Key User credentials again if you reset your PIN.

Until you log into the MMI of the vehicle to connect your myAudi PIN, your eight-digit myAudi PIN will be shown on the Vehicle page of the app. After pairing, iOS users can still locate their PIN in the Vehicle Connections area of the app’s Profile tab. This feature will soon be available for Android.

The Audi valet key is missing.

For a very long time, robbers have been after valet keys. The owner’s handbook and valet key are frequently left in vehicles’ glove boxes, and criminals are aware of this. If a burglar takes an automobile using a valet key, that is even a different kind of crime.

The valet key for some Audi automobiles is located in the glove box, and thieves discovered this. To prevent thefts, Audi has advised drivers to remove the valet key from the glove box.

What does the button for valet override do?

The owner can momentarily disengage the alarm feature of the system using the valet button or switch. You can enter or exit valet mode by disarming the system with a functional transmitter, your unique manual override code, or by following the steps below.

When the car is in valet mode, what happens?

The valet switch makes it unnecessary for you to provide your transmitter to parking attendants or garage personnel by momentarily disabling all alarm functionalities. All alarm features are disregarded when the system is in valet mode, but the remote panic feature and remote door locks are still functional. The system must first be disarmed before the valet mode can be used. You can do this by using the key chain transmitter or by turning on your unique manual override code.

  • Turn the ignition key to the on position before getting inside the car.
  • Turn the valet switch to the off position or press and hold the valet pushbutton switch. The valet mode of the system will not be changed.
  • Make sure the ignition is turned to the on position, depress and release the pushbutton switch, or turn the valet switch to the on position to resume regular operation.

NOTE: Never forget to switch off valet mode. This will guarantee that the car is always kept safe.

How do I stop Dronemobile’s valet mode from working?

The alarm system and the remote starter will be turned off when the Compustar system is in valet mode. Only the remotes will still be able to lock and open the doors without a key.

How to determine whether my computer is in valet mode:

  • You will experience three vehicle parking light flashes, followed by ten more, when you try to remote start your car.
  • An error message stating that the car is in Valet mode will appear when you try to remote start it with the DroneMobile app.
  • Z’s will be seen on the LCD screen of your remote control, giving the impression that the car is in sleep mode.
  • The parking lights will typically flash once for lock and again for unlock when you use your remote to lock and unlock your car. However, the vehicle is in valet mode if the parking lights are not flashing (unless the installer did not hook up the parking lights upon installation).

Exiting Valet Mode

  • If you don’t have a Compustar remote, kindly complete these steps:
  • Start the car.
  • Within 10 seconds, depress and release the foot brake 10 times.
  • Valet Mode won’t be activated by this technique; it will only be deactivated. When the system exits valet mode, the parking lights on the car should flash twice.