If you are jacking up the front wheel, the jack goes directly behind it; if you are jacking up the rear wheel, the jack goes directly in front of it. There ought to be a small mark along the rail. Start elevating the car after positioning the jack beneath the location. Lift the car high enough for a jack stand to fit beneath.
In This Article...
The Audi A4 2021 lacks a jack. Where is it?
- On a solid, flat surface, park the car as far away from oncoming traffic as you can.
- Turn on the parking brake.
- Turn on the hazard lights.
If there are any passengers in your car, ask them to get out and go somewhere safe.
Audi A4 Flat Tire Equipment
You should have a vehicle tool kit, tire mobility kit, and vehicle jack in your car, all of which may be found in the trunk’s luggage area underneath the cargo floor cover (trunk).
- Pull the strap holding the cargo floor cover up to reveal the front compartment (1).
- Pick up the cargo floor by the plastic handle to access the rear compartment (2).
- (2) Secure the plastic handle to the seal on the baggage compartment
- Pull the plastic lever of the cargo floor toward the back to completely remove it (2).
- If your car has a spare tire, turn the handle in the other direction to take it off.
- Before locking the lead on your trunk, unhook the cargo floor.
Depending on the vehicle’s accessories, the compressor, tire mobility kit, and tool kit may all be concealed under a different cover that is fastened with a hand wheel.
If your vehicle has a storage bag for the jack, the storage bag is fastened with tie-straps in the baggage area and needs to be fastened again after use.
Using The 2020 Audi A4 Tire Mobility Kit
The use of slime to inflate a flat tire is only a temporary solution. If feasible, replace the damaged tire right away. Never remove a nail or other sharp object that has punctured a tire from the tire. Temperatures as low as (-4F) or below can be used with the tire mobility kit (-20C).
Where is the jack in the 2017 Audi A4?
Always give the jack* a stable platform on the ground. (The vehicle’s tool kit has the jack.) Use a sizable, sturdy board or another type of support if necessary. To stop the jack from slipping on a hard, slippery surface (like tiles), use a rubber pad or something comparable.
Find the Fig. 315o indication on the door sill that is closest to the wheel that needs to be changed. The indication under the door sill is in front of the jacking point.
When the jack’s claw completely encircles the seam on your car, turn the knob to wind up the jack* underneath the jacking point on the door sill.
Place the jack* so that its base plate is flat on the ground and its claw (A) fits around the seam. The jacking point (A) must be supported vertically by the base plate (B).
Now attach the crank handle to the jack by fitting it into the knob’s aperture. To fix the crank handle in place, turn it either clockwise or counterclockwise.
Wind the crank handle to raise the car till the broken wheel is off the ground.
- Verify the jack’s stability. The jack runs the risk of slipping or sinking in if the ground beneath it is slick or mushy.
- To raise the car, only use the jack* that came with it. The risk of injury increases if you use a jack from another vehicle because your car can slide off the jack.
- Only use the jack* at the jacking points that are behind the door sill markings, and make sure it is properly aligned. If the jack* is not correctly engaged, there is a danger of damage since it may suddenly slip off.
- Never start the engine when the chance of an accident is high!
- If work is to be done below the vehicle, make sure it is securely supported on appropriate supports to reduce harm risk!
It is forbidden to raise the car on its sills. Only use the jack* at the jacking locations that are behind the door sill markings. In the absence of that, your car can be harmed.
Audi A4 Toolkit: Where Is It?
Some Audi A4s have an additional cover, maybe with a knob, that conceals the tools, compressor, and tire repair kit. The tool kit can be found behind the back seats of some Audi A4s, right behind the floor panel (Fig. 2A).
On an Audi A5, where do you mount the jack?
Put the vehicle in first gear (manual transmission) or position P on the selector lever (automatic gearbox).
Find the marking (recess) on the door sill that is nearest to the wheel that has to be replaced. Fig. 1. The marker on the door sill is in front of the jacking point.
Turn the jack up until the claw completely encircles the seam on your Audi A5 (Fig. 2 -A).
Place the jack in the proper position so that the claw of the jack (A) fits around the seam and the jack (Bmovable )’s base plate is flat on the ground. The jacking point (A) must be supported vertically by the base plate (B).
In order to attach the crank handle to the jack, place it inside the knob’s opening. To fix the crank handle in place, turn it either clockwise or counterclockwise.
Wind the crank handle to raise the Audi A5 till the problematic wheel is off the ground.
Only the jacking points indicated on the door sill in Fig. 2 may be used. Each wheel has its own jacking point. Apply the jack only where indicated. Caution!.
The Audi A5 may fall off the jack if there was an unstable surface underneath it. Always provide the jack a stable basis to stand on. Use a sizable, sturdy board or another type of support if necessary. To keep the jack from slipping on a hard, slippery surface (like tiles), use a rubber pad or something comparable.
- Reduce the danger of damage by keeping the jack’s base from slipping.
- Only position it and apply the jack at the proper jacking places. The Audi A5 could roll off the jack and cause injury if it is not placed firmly.
It is forbidden to raise the Audi A5 on its sills. The Audi A5 may sustain damage if the jack isn’t used at the jacking points that are behind the markings on the door sill.
How safe are jack stands?
Some maintenance and repair tasks can only be carried out from underneath a vehicle. Although your car might have a jack, it was never intended to be used for anything other than an emergency. This introduction about car jacks and jack stands is intended to help you understand the various options for lifting your automobile off the ground.
Safety Is Paramount
This account of my friend Ken is real. Ken, a mechanic by trade, was working on a personal car in the driveway one weekend when he encountered a terrifying situation. Ken was trapped between a concrete driveway and a few thousand pounds of automotive steel when the weak factory jack he was using to keep the car off the ground broke. Ken begged for assistance, but nobody responded. He claimed to have summoned strength he had never before possessed in order to lift a corner of the car off of himself and slip out from under it.
Ken’s back was seriously hurt, and it took him months to recover and go back to normal. He sustained injuries that prevented him from working on vehicles for a living. He experienced a life-changing incident.
But the mishap was entirely avoidable. To guarantee the security of anyone operating underneath a vehicle, careful lifting techniques are essential. When changing a clutch or even slipping beneath a car for a quick visual inspection, high-quality jacks, jack stands, or ramps can keep you safe. Our buyer’s guide for jacks and jack stands explains how to pick lifting equipment that is appropriate for your requirements.
Jack and Lifting Basics
Jack stands: In a do-it-yourself garage, jack stands can be the most neglected piece of safety equipment. Jack stands cannot raise automobiles. Instead, they offer a lifted vehicle a secure, stable support. Every time you lift a vehicle, use a set of jack stands to greatly reduce the risk of getting hurt by a falling vehicle. Simply raise the vehicle’s jack stand(s) and drop it onto the stand(s). When it’s time to take them off, use a jack to raise the car a little bit, then take the jack stands off and lower it. Wheel chocks should always be installed before working on an elevated vehicle.
Ramps: Because they offer substantial, sturdy points of contact that are unlikely to fail, ramps are a secure substitute for jacks and jack supports. Ramps, however, are not as adaptable as jacks and jack stands. For instance, a ramp is useless if you have to remove a wheel to replace brake pads. But ramps are perfect for muffler replacement jobs.
Floor jacks: A jack included in a car’s spare tire changing kit is not appropriate for usage in other circumstances. These jacks are normally made to be compact and lightweight, making them perfect for minor roadside emergencies only. A good floor jack is a necessary item for routine lifting tasks around the shop or garage. Pick a floor jack with a lifting pad that has a minimum diameter of two inches. This will provide the jack point of the car with a lot of surface area to rest on. A floor jack will roll into a stable position when the car raises because it is on wheels. Before starting your task, make sure to lower the car onto jack stands.
Bottle jacks: Bottle jacks are more portable than floor jacks and frequently have higher weight ratings than floor jacks of comparable price. Bottle jacks, however, could not be as stable as floor jacks because they often have a smaller footprint. To reduce the danger of movement, use bottle jacks only on a stable, level surface, such as a garage floor. Just as you would with a floor jack, use jack stands when using a bottle jack.
Equipment for specialty lifting: Specialized tools make it easier and safer for both amateurs and professionals to complete particular tasks. To remove a transmission from a car safely, a transmission jack slips smoothly under the transmission. With the least amount of risk to you or your car, you can raise an entire engine out of its bay using an engine hoist or engine crane. A specialised lift is a terrific way to complete the task fast and safely if you conduct a lot of heavy wrenching.
Popular Jacks and Lifting Equipment
The popular automobile jacks, ramps, jack stands, and other lifting tools offered by NAPA AUTO PARTS are shown in the charts below. We advise selecting a jack with a capacity rating that is nearly equal to the curb weight of the car it is lifting. A two ton jack, for instance, would be required for a 4,000 pound (two ton) SUV. With the jack, you won’t be able to lift the entire car at once, but it still provides a good amount of safety.
Do jack stands for 2 tons suffice?
Each type of automobile jack is rated to support a particular weight range, and the precise rating is listed on the jack itself in the form of a clearly visible sticker. It’s crucial to realize that you won’t be lifting your car or truck in its whole with a single jack, so you don’t need one that is rated for the vehicle’s total weight. A two-ton jack should be adequate for elevating a corner on the majority of sedans and small automobiles. In order to provide you with the necessary margin of safety, a pickup truck or SUV may need to be rated at double that weight (four tons).